Rosewill RC-302 User manual

1 ports Parallel PCI Adapter RC302
User Manual

1 ports Parallel PCI Adapter RC302 User Manual
3
Overview
This PCI card is a single 1284 parallel port controller with PCI bus interface and supports the existing centronics printer
interface as well as PS2, EPP & ECP modes and uses an all-in-one solution from NetMos Technology, which provides
superior performance and unmatched data transfer rates. The most advanced feature is it uses of a single interrupt,
which is set automatically by the host system and share among all on-board I/O ports.
Features
yChipset: NetMos Nm 9715
yData Transfer Rate: 1.5Mbytes/s(parallel port)
yBus: PCI 32bit, 33MHz.
yLow power: Single 5V operation
yHigh speed transfer, single parallel port
yMulti-mode compatible controller (SPP, PS2, EPP &ECP)
y16Byte FIFO (parallel)
ySoftware programmable mode selects
ySupports Window98, Window95, Window2000 & Window NT 4.0
Installing the PCI I/O controller card into your computer
Turn off your computer and all external devices connect it.
Disconnect your computer from the power sources.
Open the computer case. Refer to your computer user manual for more details.
Find an available PCI slot and remove the slot bracket. Save the bracket screw for later use.
Align the PCI I/O controller horizontally with respect to the PCI slot and insert it into the slot firmly and evenly. Take care
not to force it into the slot. Once you have properly positioned the PCI I/O controller card into the slot, fasten it to the
computer case with the bracket screw you have saved.
Close the computer case. Make sure to reconnect all the external devices power cords to your computer.

1 ports Parallel PCI Adapter RC302 User Manual
4
Driver Installation
Windows 95/98/2000
Once the PCI I/O card is installed and the computer is restarted, Windows will detect the board and attempt to install
driver for it.
1. Start Windows 95/98/2000/XP
2. The“Update Device driver Wizard” will
appear, informing you that it has found a
“PCI I/O Card”. Click the “Next” button.
3. Click “Other Location” for Windows 95
or “Specify a location” for Windows 98
to install the driver.
4. Insert the driver CD in CD-ROM drive(D)
and click on the “Browse” button.

1 ports Parallel PCI Adapter RC302 User Manual
5
5. at the “Browse” option, select
“CD-ROM(D)
FOLDER “PCI_I/O\NM97X5\WIN9X”
“OK”button
6. The “Update Device Driver Wizard” will
appear, informing you that it has found
the “NetMos PCI I/O Card” driver. Click
the “Next” button.
.
7. Follow the instructions to finish up the
drive installation.
.
8. Once Windows 9x has restarted, you
can now connect your external devices
to the PCI I/O card install the driver for
the external devices, please refer to the
external device user manual.
.
Windows NT 4.0
Using the existing hard disk controller in your system, you need to install the ATA/100 driver into Windows NT first.
Without ATA/100 driver support, hard drive attached to the ATA/100 IDE controller card can not boot up Windows NT.
Installing drivers with existing Windows NT 4.0:
Make sure Windows NT 4.0 is properly installed into your system first.
Step 1: Start Windows NT 4.0.
Step 2: Insert Driver CD into the CD-ROM drive.
Step 3: Select “Run” option in Windows NT.
Step 4: At the “Run” option, click on the “Browse” button.
Step 5: At the Browse for Folder window:
1. Select “CD-ROM Drive (D)”
2. Select NetMosMultiIODrivers.exe

1 ports Parallel PCI Adapter RC302 User Manual
6
3. Click on the Open button
Step 6: Finally, click the “OK” button
Step 7: Follow the instruction to finish the driver installation. Your system will automatically restart in order to complete
the driver installation.
Installing DOS Driver
Copy “D:\PCI_IO\NM97X5\DOS\NMDOSIN.EXE ” to your hard disk and run it.
Thank you for purchasing a quality Rosewill Product.
Please register your product at : www.rosewill.com/ for complete warranty information and future support for your product.