Do not assemble the loading ramp until now, in
order to prevent it from jamming on the ground
when lowering the hoisting platform –
risk of injury!
Make sure that there are no persons or their body
parts beneath or between the movable parts of
the hoist while lowering the hoisting platform.
Risk of injury! Now release the tie-down straps
and the front wheel clamp, if applicable, while an
assistant safely holds the vehicle, and roll it off
the platform in backward direction.
5. Sa ety in ormation:
• The hoisting platform may only be placed on an
even, horizontal and capable surface.
The vehicle weight must be added to the dead
weight of the hoist of approx. 135 kg!
• The hoisting platform has been tested for a
maximum load of a vehicle weight of 400 kg.
It may only be used for hoisting motorcycles
within the admissible and approved load values.
Never charge the hoisting platform with more
than the stated maximum bearing capacity
of 400 kg.
• The hoisting platform must be secured against
sliding by attaching it to the ground with the
retaining screws.
• Make sure that your working area is
sufficiently lit.
• Before putting the hoisting platform into
operation, make sure that the working area is
clean. Keep all levers and pedals dry and free
from dirt and oily resp. greasy residues.
• Before placing the vehicle on the working
platform and removing it, the latter must always
be completely lowered and cleaned from oil and
grease residues, in order to avoid oiling of the
vehicle wheels. Risk of falling!
• There should be no persons on the hoisting
platform while lifting resp. lowering it as well as
when it is pumped up. Make sure that there are
no persons or their body parts beneath or
between the movable parts of the hoist while
lifting the hoisting platform.
• When lifted, the hoisting platform must be
mechanically secured in one of the two
available positions by means of the fastening
bolt, in order to relieve the hydraulics and avoid
unintentional lowering.
• In the case of longer interruptions of work, the
working platform must always be completely
lowered.
• While working on the vehicle, the loading ramp
must be removed and not re-attached, until the
platform is completely lowered – risk of injury!
• Do not place any load on the hoisting platform,
if maintenance works are carried out under-
neath the working platform. The working plat
form must be mechanically secured against un
intentional lowering by means of the fastening
bolt.
• The hoisting platform may not be moved while
bearing load.
• The hoisting platform may not be used by any
person not sufficiently experienced with
operating it.
• The hoisting platform should be positioned, so
that it cannot be operated by any unauthorised
person and it should not be accessible for
children.
• Please make sure that the notification stickers
on the hoist remain legible, even after longer
and regular use of the platform.
• Since this hoisting platform is a universally
applicable product without a specific vehicle
classification, it is important to make sure that
the hoist can be used/applied with your vehicle
without any problems and in an appropriate way,
before the first use. Thereby pay attention to
the information on your vehicle operating in
structions and the vehicle manufacturer’s speci-
fications. This is necessary, since an inappro
priate use of the product will affect the driving
safety and/or the condition of the vehicle.
6. Maintenance and care
• The chromed push bar of the hydraulic cylinder
must be kept clean and protected from
mechanical exposure. Dirt or damaging could
lead to leakage of the hydraulic jack.
• Never clean the hoisting platform with a high-
pressure cleaner. The high pressure could wash
the grease from the bearings.
• Use an acid-free motor vehicle cleaner for
cleaning the hoisting platform.
• All movable parts must be greased with bearing
grease and all screws must be retightened
every three months. The shaft bearings can be
additionally oiled through existing boreholes.
• Check the hoisting platform for signs of
corrosion or other damages at regular intervals.
• Position the hoisting platform in a dry and
well-aired location, in order to protect it from
corrosion.
• The hydraulics and mechanics of the hoisting
platform may only be dismantled and repaired
