Royal garden BWKSEC207 User manual

Assembly Instructions
Blonde Wicker Sectional Set - Chaise Lounge
Questions, problems, or missing parts?
Before returning to the store, call Customer Service.
1-866-988-3300
8 a.m. - 5 p.m., PST Monday - Friday
Model No. BWKSEC207
Retain this manual for future use.
1

BWKSEC207
Contents
Safety Instructions
Parts List
Assembly
Securing The Sectional
3
4
5
10
Cleaning & Maintenance
Warranty
11
12
IMPORTANT: RETAIN FOR FUTURE REFERENCE, AND READ CAREFULLY.
2

WARNING
Please keep children out of the assembly
area before assembly.
WARNING
Never use this product as support. Do not shake,
lean, or climb on the product at any time.
WARNING
Do not place heavy objects on the chaise lounge.
WARNING
When not in use, secure the product in a cool
and covered location.
WARNING
Do not locate the product near any heat source.
WARNING
Warning: Weight limit for the chaise lounge is
250lbs (113.4Kg).
Safety Instructions
BWKSEC207
3

Parts List
A
Left Arm - 1
C
Back - 1
E
Seat Cushion - 1
F
Back Cushion - 1
G
Flat Washer + Bolt (M6x20MM) - 5+1
H
Flat Washer + Bolt (M6x45MM) - 2+1
I
Flat Washer + Bolt (M6x50MM) - 10+1
J
Allen Wrench - 1
B
Seat - 1
D
Leg - 5
BWKSEC207
C
A
D
B
F
E
4

Assembly
STEP 1
Requires: B, C, G, H, J
Place seat (B) on a flat protected surface while holding it on its side as shown.
Attach back (C) to seat (B) with flat washer and short bolt (G), flat washers and long bolts (H)
using Allen Wrench (J). Do not tighten completely.
BWKSEC207
H
B
C
G
5

Assembly
STEP 2
Requires: A, B, C, G, J
Rotate assembled unit to the position as shown.
Attach left arm (A) to seat (B) and back (C) with flat washers and short bolts (G)
using Allen Wrench (J). Do not tighten completely.
BWKSEC207
G
C
A
B
6

Assembly
STEP 3
Requires: A, C, G, J
Rotate assembled unit to the standing position.
Connect left arm (A) to back (C) with flat washer and short bolt (G), using Allen Wrench (J).
Do not tighten completely.
BWKSEC207
G
CA
7

Assembly
STEP 4
Requires: A, B, C, D, I, J
Rotate assembled unit upside down.
Connect legs (D) to left arm (A), seat (B) and back (C) with flat washers and long bolts (I) using
Allen Wrench (J). Do not tighten completely.
Completely tighten all bolts with Allen Wrench (J) from steps 1 through 4.
BWKSEC207
C
D
A
B
II
8

Assembly
STEP 5
Requires: E, F
Rotate assembled unit to the standing position.
Place seat cushion (E) on chaise lounge.
Place back cushion (F) on chaise lounge.
Assembly is complete.
BWKSEC207
9

BWKSEC207
STEP 1
Securing the Sectional
10
X2

Cleaning & Maintenance
• For best results, clean the fabric with a damp cloth and dry thoroughly. This will help
prevent mildew by removing dirt particles that may accumulate.
• Do not clean with abrasive materials, bleach, or solvents.
• Store the seating set in a dry, sheltered place when not in use.
weather such as rain, hail, sleet, snow, or wind.
BWKSEC207
11

Warranty
Outdoor Furniture
IMPORTANT
If you have any problems with this product (missing or damaged parts, assembly issues, etc.),
PLEASE DO NOT RETURN TO THE RETAILER/STORE
from where you purchased the product.
Please call our Toll-Free Customer Service Hotline at:
1-866-988-3300
Between 8:30 AM and 5:00 PM Pacific Standard Time, Monday through Friday
To expedite any future warranty claims, please retain the instruction sheet, warranty card and
receipt for future use.
Care and Maintenance
Frame: Wipe clean with a mild soap and water solution, rinse with clean water, and dry throughly.
Cushion: Spot clean with a soft, damp cloth.
Do not stand or climb on chaise lounge.
In order to prolong the life of your chaise lounge, please store in dry sheltered place when not in
use or during inclement weather.
**We recommend that you save the Allen Wrench and periodically tighten all bolts.
BWKSEC207
12

Warranty
Outdoor Furniture
1-YEAR LIMITED WARRANTY PROGRAM
Contact Customer Service at 1-866-988-3300
For a period of one (1) year after date of purchase, the Manufacturer will either repair or replace defective
components in accordance with this Limited Warranty. This warranty is between the Manufacturer and the
original purchaser and is valid only when accompanied by the original purchaser’s sales receipt showing
original date of purchase and location of purchase. Replacements under this warranty revert back to the
date of original purchase for future warranty.
warranty applies in normal residential use only and is not intended for commercial use. The Manufacturer
can make substitutions as required of materials, components, and sub-components of comparable value
and utility. This warranty is limited to product repair or replacement (to be determined solely by the
Manufacturer). Warranty return is limited to only the single affected component.
This limited warranty covers only manufacturing defects and does not cover normal wear and tear, damage
chemical damage from suntan oil or other chemicals, exposure to extreme heat or cold, abrasion or
excessive weight. This product is intended to be used in standard installations only. This warranty is void
if the product is not used for its intended purpose. The Manufacturer disclaims liability for any aspect of
installation and any inconvenience caused by a defective part of a component.
Certain items are not covered by this warranty. These include, but are not limited to the following:
1. Components subjected to abuse, including abuse intended to simulate failure.
2. Damages caused by retailer, shipper or installation crew (such as scratches, dents, tears, chips, etc.).
3. Any part which merely exhibits normal wear yet functions essentially as new, including chips, scratches or
stretching of materials and stitching.
4. Tears, punctures, scratches or any damage caused by improper installation or use.
temperatures is not covered. General frame rusting is not covered.
6. Fading and/or discoloration of fabrics/cushions/straps/wicker resulting from exposure to the elements,
7. Umbrella bases are not covered under any circumstances.
To make a claim, call the toll-free number below. Please have available a copy of the original sales receipt
along with a brief description of the problem. Please also provide your email address and daytime telephone
or cell phone number. All items may be charged actual freight costs plus $15 for handling. Repairs or
replacement will be made at the Manufacturer’s option. Sales and use taxes, plus shipping and handling
charges are the responsibility of the consumer.
THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER NEITHER MAKES
THOSE OF RETAILING DEALERS. THIS EXCLUSIVE REMEDY IS LIMITED TO RECEIPT OF A CREDIT IN
CONNECTION WITH THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR COMPONENT DEEMED
TO BE DEFECTIVE UNDER THE TERMS AND CONDITIONS AS STATED IN THIS WARRANTY. NEITHER
ARISING OUT OF ANY BREACH OF THIS WARRANTY OR NEGLIGENCE EVEN IF IT HAS BEEN ADVISED
ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES OTHER THAN THE WARRANTY DESCRIBED
OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DISCLAIMED.
BWKSEC207
13

Assembly Instructions
Blonde Wicker Sectional Set - Loveseat
Questions, problems, or missing parts?
Before returning to the store, call Customer Service.
1-866-988-3300
8 a.m. - 5 p.m., PST Monday - Friday
Model No. BWKSEC207
Retain this manual for future use.
1

BWKSEC207
Contents
Safety Instructions
Parts List
Assembly
Securing The Sectional
3
4
5
10
11
Cleaning & Maintenance
Warranty 12
IMPORTANT: RETAIN FOR FUTURE REFERENCE, AND READ CAREFULLY.
2

WARNING
Please keep children out of the assembly
area before assembly.
WARNING
Never use this product as support. Do not shake,
lean, or climb on the product at any time.
WARNING
Do not place heavy objects on the loveseat.
WARNING
When not in use, secure the product in a cool
and covered location.
WARNING
Do not locate the product near any heat source.
WARNING
Warning: Weight limit for the loveseat is
500lbs (226.8Kg).
Safety Instructions
BWKSEC207
3

Parts List
A
Right Arm - 1
C
Back - 1
E
Seat Cushion - 1
F
Back Cushion - 2
G
Flat Washer + Bolt (M6x20MM) - 5+1
H
Flat Washer + Bolt (M6x45MM) - 3+1
I
Flat Washer + Bolt (M6x50MM) - 8+1
J
Allen Wrench - 1
B
Seat - 1
D
Leg - 4
BWKSEC207
C
A
DB
F
E
4

Assembly
STEP 1
Requires: B, C, G, H, J
Place back (C) on a flat protected surface.
Connect seat (B) to back (C) with flat washer and short bolt (G), flat washers and long bolts (H)
using Allen Wrench (J). Do not tighten completely.
BWKSEC207
H
B
C
G
5

Assembly
STEP 2
Requires: A, B, C, G, J
Connect right arm (A) to seat (B) and back (C) with flat washers and short bolts (G) using Allen
Wrench (J). Do not tighten completely.
BWKSEC207
G
B
C
A
6

Assembly
STEP 3
Requires: A, C, G, J
Rotate assembled unit to the standing position.
Connect back (C) to right arm (A) with flat washer and short bolt (G), using Allen Wrench (J).
Do not tighten completely.
BWKSEC207
A
G
C
7