Royal HT3SL Quick start guide

379 Campus Drive
Somerset, NJ 08875
HT3SLIM0902HF
ROYAL®
HT3SL crosscut shredder
HT3SL crosscut shredder
OPERATIONAL
MANUAL
STANDARD WARRANTY
OLIVETTI OFFICE USA, Inc. d/b/a ROYAL CONSUMER
BUSINESS PRODUCTS ("Royal"), 379 Campus Drive
Somerset, NJ 08875. WARRANTS that your NEW Royal
product is free of defects of workmanship and materials.
If there is a defect or malfunction of this product, Royal will repair it free of charge as follows:
PARTS: New or comparable rebuilt parts in exchange for defective parts for ONE YEAR from
date of customer purchase.
LABOR: Royal provides labor warranty for 1year from date of end-user purchase. Product must
be sent postage prepaid and insured to Royal. At completion of the repair, the consumer will be
responsible for return shipping charges from Royal, and for any parts or services no longer
covered under warranty. This warranty does not apply to persons who purchased this product
second hand or used.
circumstances beyond the control of Royal, including but not limited to, fire, or other casualty,
accident, neglect, abuse, abnormal use or battery leakage damage.
THERE ARE NO OTHER EXPRESSED WARRANTIES EXCEPTAS STATED HEREIN.
AFTER THE PERIOD OF EXPRESSED WARRANTY SET FORTH HEREIN, THERE ARE
NO EXPRESSED OR IMPLIED WARRANTIESAND THOSE EXCLUDED INCLUDETHOSE
OF MERCHANTABILITYAND FITNESS FOR PARTICULAR PURPOSE. Royal shall NOT
be held liable for
CONSEQUENTIAL DAMAGES resulting from any failure, defect or malfunction of this product.
Some States do not allow limitations on how long an implied warranty lasts and some States do
not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations may not apply to you.
WARRANTY PROCEDURES
Royal has taken great care to insure the product you have purchased will provide years of trouble-
free service. Should the product require service within the first 30 days after purchase, Royal
strongly recommends you return the product to the place of purchase for replacement. Please
note this 30-day replacement period may be subject to the limitations of the return policy that
has been established by your retailer, may not be available at your retailer, or may be for a
different period of time as established by your retailer. Your retailer may allow exchanges past
this 30-day period. Should this be the case, Royal strongly recommends you return the product
to the place of purchase for replacement.
TO OBTAIN SERVICE UNDER THE TERMS OFTHIS WARRANTY:
In the event you are unable to obtain a replacement product from your retailer,
please do the following:
1. Send a copy of your original sales receipt showing original purchase date along with your
mailing address and a note describing the nature of the problem to:
Royal Consumer Warranty Processing
PO Box 161
Jaminson, PA 18929-0161
DO NOT RETURN THE PRODUCT TO THIS ADDRESS!
2. You will receive a return authorization number within 7-10 business days from the date your
return request is received if it is determined that there is a basis for a replacement product.
The return authorization form you receive will list the return procedures, applicable charges,
if any, and the correct shipping address for the returned product.
PRODUCT SUPPORT HOTLINE:
For questions on use of this product call 800-272-6229 Monday through Friday between the
hours of 8:30AM and 5:00PM EST. You can also email Royal at [email protected]. Allow two
to three weeks for email response.
ROYAL®
ROYAL
®
Royal Consumer Information Products, Inc.

12
HT3SL Paper Shredder / Pencil Sharpener / Letter Opener
Setup:
1. Place the Pencil Shavings Retention Cup provided with your shredder, inside the
metal ring attached to the inside of the wire mesh basket.
2. Place the shredder head securely on top of the wastebasket. Make sure that the
shredder head sits flush on top of the wastebasket or else the shredder sharpener
and opener will not work.
3. Plug the power cord into any standard 115 voltAC outlet.
4. Place the Power Slide Switch in the AUTO position.
Operating the shredder:
The model HT3SL Power Slide Switch is located on the top of the shredder. The main
switch has three (3) settings:
1. When AUTO is selected, the shredding process is started automatically by inserting
the folded paper into the feed opening. The shredder will stop automatically when
the paper has completed its travel through the feed opening.
2. OFF is used to terminate theAC power to the shredder. This mode is recommended
when the shredder is not being used for a prolong period of time. When the switch
is in the OFF position, the Shredder, Sharpener and Opener will not work.
3. REV is used to assist in the removal of a paper jam, which reverses the shredding
process prior to a completed cycle, thus clearing the cutters.
Shredder capacity:
The HT3SL will shred up to three (3) folded sheets of 20 lb. bond paper and will accept
paper widths up to 5". When shredding small material like envelopes or receipts,
insert them through the middle of the feed opening.
Cautions:
1. Keep all loose articles of clothing, ties, jewelry, hair or other small items away from
the feed opening to prevent injury.
2. Keep in the OFF position when the shredder is not in use for prolong periods of
time.
3. Remove all paper clips and staples from paper before shredding. The HT3SL will
cut staples however it is not recommended.
4. Do not place hands or fingers into the shredder throat as serious injury could result.
5. Continuous shredding of computer paper should not exceed 2 minutes. If continuous
use is required at the maximum sheet capacity (3 folded sheets), it is recommend
that shredding time should be 2 minute on and 4 minute off to allow for proper
cooling of the motor.
6. Always turn off or unplug the shredder prior to moving, cleaning or emptying the
wastebasket.
7. Empty wastebasket frequently.
Paper jams and motor overload situations:
The HT3SL is equipped with a motor overload protection device. The normal short
duty cycle for continuous shredding at maximum capacity is 2 minutes on and 4 minutes
off. The power may terminate automatically in case of the following abnormal situations:
1. Operating the shredder at the maximum 3 folded sheet capacity continuously for
a prolonged period of time, eg. more than 2 minutes without stopping.
2. Exceeding the shredding capacity, eg. inserting more than three (3) sheets of 20
lbs. paper at one pass, or if the paper is not fed squarely into the feed opening.
HT3SL Paper Shredder / Pencil Sharpener / Letter Opener
Both abnormal operations may result in the activation of the thermal motor overload
protection which terminates the power to the shredder. A major paper jam could cause
the thermal motor overload protection to terminate AC power to the motor. Never
allow the shredder to remain in a jammed condition with the AC power turned on. If
this occurs you should:
In case of a major paper:
1. Set the power switch to the OFF position or unplug the power cord from the AC
outlet and wait at least 15 minutes for the thermal overload protection to reset.
2. Grasp the excess paper from the top and pull it out as you place the power switch
in the REV position. Be careful not to place your fingers near the feed opening or
else serious harm could result.
3. Set the power switch back to the AUTO position.
4. You are now ready to resume normal shredding.
Pencil Sharpener
1. To prevent motor damage, remove the pencil from the pencil opening when point
is sharpened.
2. Refrain from inserting hard materials such as pens, chalk, crayons or coloring pencils
which will damage or clog the cutting blades. Maximum pencil diameter should not
exceed 7.4mm. Standard #2 type pencil recommended
To use the Sharpener:
1. With the switch in theAUTO position, insert the pencil into the pencil opening. The
sharpening starts immediately.
2. Pull out pencil at the end of the sharpening cycle.
3. Be sure to empty the pencil shavings retention cup frequently.
To use the Letter Opener:
1. Be sure that the letter inside the envelope is not against the leading edge of the
envelope will be inserted into the opener.
2. With the switch in theAUTO position, place the leading edge of the envelope into
the opening of the Letter Opener. The cutters will start and feed the envelope through
automatically.
Specifications:
Shred Type: Cross-Cut
Shred Width: 5/328" X 1"
Shredding Capacity: 3 Folded Sheets
Feed Opening: 5"
Dimension: 10"(H) x 9(W) x 7(D)"
Weight: 7 lbs.
Input: 115 volt AC, 2.5 amp.
WARRANTY, REGISTRATION & TECHNICALSUPPORT
PLEASE FILL OUT AND RETURN THE WARRANTY CARD INCLUDED WITH YOUR
NEW ROYAL PRODUCT OR FILL OUT THE WARRANTY REGISTRATION FORM ON
THE ROYAL WEB PAGE AT WWW.ROYAL.COM. IT ENTITLES YOU TO PRODUCT
WARRANTYAND TECHNICAL SUPPORT UNDER THE TERMS AND CONDITIONS
DESCRIBED HEREIN.
BE SURE TO KEEPACOPY OFYOUR SALES RECEIPT!