Royalcraft Pod Chair User manual

Pod Chair
Assembly Instructions
Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd.  1 / 6

www.a-mir.co.uk
Product size:
100*120*H195 cm
WARNING:
DO NOT USE THIS POD CHAIR AS A SWING!
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY

Pod Chair
Assembly Instructions
Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd.  2 / 6

www.a-mir.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Do not stand or climb onto this product.
This product is intended for domestic use only.
Ensure the product is always placed on level ground.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Unwrap all packaging materials and place the components on
suitable surface to prevent scratching your product.
Check the pack and make sure you have all parts listed.
Check all screws and bolts are tightened and inspect regularly.
This product is suitable for all year outdoor use, but we
recommend that a furniture cover be used to add additional
protection to your product when not in use.
PLEASE NOTE - All cushions should be stored indoors after use.
The cushions are not waterproof.
During severe weather conditions and in the winter months we
recommend moving your furniture inside into a cool, dry place.
Before storage, ensure that the product is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipe with a clean, dry cloth.
Don’ts
Never tilt the chair during use.
Do not stand or climb onto the product.
Do not use power tools to construct this product.
Do not sit or lean onto the rims of this product.
Do not use this product if parts are missing, damaged or worn.
Never use scourers, abrasives or chemical cleaner.
Do not use this product as a ladder as this could lead to the product
becoming unbalanced and overturning.
Never drag furniture when moving it, always lift it.
DO NOT SWAY THIS
PRODUCT VIOLENTLY.
DO NOT USE THIS POD
CHAIR AS A SWING!
Number of people required for assembly
Two People
Time to assemble
20 minutes
Tools required

Pod Chair
Assembly Instructions
Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd.  3 / 6

www.a-mir.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No.
Diagram Qty Part No. Diagram Qty
A
Hanging Pole w/
Safety Belt
1 PC B
Base
1 PC
C
Seating Part
1 PC D
Seatpad
1 PC
E
Backrest
Cushion
1 PC F
Hanging Pin
1 PC
G
Chain
1 PC H
Washer
4
PCS

Pod Chair
Assembly Instructions
Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd.  4 / 6

www.a-mir.co.uk
I
Bolt Head Cap
2 PCS J
M8*60mm Bolt
2
PCS
K
Nut
2 PCS L
Nut Cap
2
PCS
M
Spanner
1 PC
Step by step assembly instructions

Pod Chair
Assembly Instructions
Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd.  5 / 6

www.a-mir.co.uk
Step One
Attach Hanging Pin (F) to Hanging Pole (A).
Insert Hanging Pole (A) into Base (B) and
align the location holes.
Ensuring the Washers (H) are in place as indicated,
insert Bolts (J) into the location holes and
attach Nuts (K).
When both nuts rotate freely on the Bolts,
tighten the nus with Spanner (M) and
add Bolt Head Caps (I) and Nut Caps (L).
Step Two
Attach Chain (G) to the Hanging Pin (F) using the nut and
bolt assembly, which is pre-fitted to Chain (G).

Pod Chair
Assembly Instructions
Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd.  6 / 6

www.a-mir.co.uk
Step Three
Attach Seating Part (C) to the Chain (G) with the carabiner.
Ensure the carabiner is fully closed and secure before use.
Fasten the safety belt to the Seating Part (C).
Step Four
Place Seatpad (D) and Backrest Cushion (E) onto
the Seating Part (C).
The Pod Chair is now ready to use.
Never tilt the Chair during use.
Ensure the product is always placed firmly
on the ground.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE