Royalcraft FARO-01 User manual


 




The intended use of this product is for domestic use only.
Important, please retain for future reference.
Read carefully.
 .a-mir.co.uk
 
A Mir Co., Ltd. 1 / 12

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 2 / 12
www.a-mir.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Do not stand or climb onto this product.
This product is intended for domestic useonly.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Remove all packaging and banding and place the components
carefully on suitable surfaces to prevent damaging or scratching
them.
Check the pack and make sure you have all of the parts listed.
Check all screws and bolts are tightened and inspect regularly.
This product is suitable for all year outdoor use, but we
recommend that a furniture cover be used to add additional
protection to your product when not in use.
PLEASE NOTE - All cushions should be stored indoors after use.
The cushions are not waterproof.
During severe weather conditions and in the winter months we
recommend moving your furniture inside into a cool, dry place.
Before storage, ensure that the product is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipe with a clean, dry cloth.
Cushions should be cleaned following the care instruction on the
label.
Don’ts
Do not use scourers, abrasives, washing powders, chemical cleaners
or any other substances containing abrasives since these substances
can damage the product, including the glasspanel.
Never tilt the chair during use.
Do not place very hot or very cold items on the glass surface
unless adequately thick table-mats are used to prevent such
items from coming into contact with the glass.
Do not use the glass as a chopping surface. Do not strike glass
with hard or pointed items.
Do not strike the glass with hard or pointed items.
Do not use power tools to construct this product.
Do not use this product if parts are missing, damaged or worn.
Do not sit or lean on the table.
Do not stand or climb onto the product and do not use it as a ladder,
as this could lead to it unbalancing and overturning.
Never drag furniture when moving it,always lift it.
Number of people required for assembly
Two people
Time to assemble
45 minutes
Tools required
Tips:
Do NOT fully tighten bolts before
all components are connected.
Only fully tighten once you are
satisfied with the alignment of all
components.
Do not overtighten bolts.
(Rubber Hammer may be required, not provided)
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 3 / 12
www.a-mir.co.uk
This Set is composed of 4 pieces.
Please find the member parts.
Member Part
Part No. Diagram Name Qty.
MP1 Coffee Table 1 PC
MP2 Arm Chair 2 PCS
MP3 Bench 1 PC
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 4 / 12
www.a-mir.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
A
Coffee Table Leg
2 PCS A1
Coffee Table Leg
2 PCS
C
Coffee Table Top
1 PC D
Coffee Table Connecting
Ring
1 PC
ML
Middle Leg
1 PC LS
Left Leg/Armrest
3 PCS
RS
Right Leg/Armrest
3 PCS S
Seat Panel
4 PCS
mm
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
0
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 5 / 12
www.a-mir.co.uk
B
Backrest
4 PCS CF
Front Bar
4 PCS
CR
Rear Bar
4 PCS L
Bolt
32
PCS
M
Spanner
1 PC
Step by step assembly instructions
MP1 – Coffee Table
Step One
Attach Coffee Table Legs (A) and (A1) to the Connecting Ring (D).
ADA1
A1 A
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 6 / 12
www.a-mir.co.uk
Step Two
Attach the above partly-assembled parts to the Coffee Table Top (C).
Place the Coffee Table in the upright position.
Your Coffee Table is now ready for use.
MP2 – Arm Chair
Step One
Attach Front Bar (CF) to the Left Leg/Armrest (LS)
and Right Leg/Armrest (RS).
C
LS
RS CF
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 7 / 12
www.a-mir.co.uk
Step Two
Attach Rear Bar (CR) to the Left Leg/Armrest (LS) and Right Leg/Armrest (RS).
Step Three
Attach the Seat Panel (S) to the above partly-assembled components.
S
LS
CR RS
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 8 / 12
www.a-mir.co.uk
Step Four
Attach the Backrest (B) to the Left Leg/Armrest (LS) and Right Leg/Armrest (RS).
Step Five
Make all components are aligned properly, loosely attach Bolts (L) to the joints, tighten the Bolts (L) by
Spanner (M). Do not over-tighten. There are 8 Bolts for each Chair.
Place the Arm Chair in upright position.
Your Arm Chair is now ready for use.
RS
LS B
L
M
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 9 / 12
www.a-mir.co.uk
MP3 – Bench
Step One
Attach Front Bar (CF) to the Left Leg/Armrest (LS) and Middle Leg (ML).
Step Two
Attach Rear Bar (CR) to the Left Leg/Armrest (LS) and Middle Leg (ML).
LS
CR ML
LS
ML CF
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 10 / 12
www.a-mir.co.uk
Step Three
Attach Front Bar (CF) to the Right Leg/Armrest (RS) and Middle Leg (ML).
Step Four
Attach Rear Bar (CR) to the Right Leg/Armrest (RS) and Middle Leg (ML).
LS
CF
ML
RS
RS
ML
CR
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 11 / 12
www.a-mir.co.uk
Step Five
Attach the Seat Panel (S) to the above partly-assembled components.
Step Six
Attach the Backrests (B) to the Left Leg/Armrest (LS), Middle Leg (ML) and Right Leg/Armrest (RS).
S
S
RS ML LS
B
RS
LS
ML
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 12 / 12
www.a-mir.co.uk
Step Seven
Make all components are aligned properly, loosely attach Bolts (L) to the joints, tighten the Bolts (L) by
Spanner (M). Do not over-tighten. There are 8 Bolts for each Chair.
Place the Bench in upright position.
Your Bench is now ready for use.
Never tilt the product during use.
Ensure the product is always placed firmly
on the ground.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
L
M
L
M
Faro 4pcs Conversation Set
- Slatted Wood Grain Effect
Assembly Instructions