Royalcraft Cannes KD Carver User manual

Cannes KD Carver Chair incl.
cushion
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 1 / 6

www.ro
y
alcraft.co.uk
Product size:
W59*D61*H90.5 cm
This product is for Domestic use only!
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY

Cannes KD Carver Chair incl.
cushion
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 2 / 6

www.ro
y
alcraft.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Do not stand or climb onto this product.
This product is intended for domestic use only.
Ensure the product is always placed on level ground.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Unwrap all packaging materials and place the components on
suitable surface to prevent scratching your product.
Check the pack and make sure you have all parts listed. In the
event of problems or missing parts, please contact the seller.
Check all screws and bolts are tightened and inspect regularly.
We recommend the use of furniture covers to protect your product
when not in use.
This product is suitable for all year outdoor use, but we
recommend that a furniture cover be used to add additional
protection to your product when not in use.
PLEASE NOTE - All cushions should be stored indoors after use.
The cushions are not waterproof.
During severe weather conditions and in the winter months we
recommend moving your furniture inside into a cool, dry place.
Before storage, ensure that the product is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipe with a clean, dry cloth.
Don’ts
Never tilt the chair during use.
Do not stand or climb onto the product.
Do not use power tools to construct this product.
Do not sit or lean onto the rims of this product.
Do not use this product if parts are missing, damaged or worn.
Never use scourers, abrasives or chemical cleaner.
Do not use this product as a ladder as this could lead to the product
becoming unbalanced and overturning.
Never drag furniture when moving it, always lift it.
Number of people required for assembly
One person
Time to assemble
20 minutes
Tools required
Tips:
It is best not to fully tighten the nuts and
bolts until they are all correctly located.
Only carefully tighten them when you are
satisfied with the alignment of all
components.
Be careful not to overtighten.

Cannes KD Carver Chair incl.
cushion
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 3 / 6

www.ro
y
alcraft.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty Part No. Diagram Qty
A
Backrest
2 PCS B
Front Leg
2 PCS
C
Left Armrest/Leg
2 PCS D
Right Armrest/Leg
2 PCS
E
Seat Panel
2 PCS F
Cushion
2 PCS
F1 
Spanner
1 PC F2
Bolt Head Cap
12 PCS
F3
Washer
12 PCS F63
M6*20mm Bolt
12 PCS
Please note the diagram is for reference only, it may not fully represent the
actual appearance of the parts.
The quantity marked is for 2 PCS Chairs.

Cannes KD Carver Chair incl.
cushion
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 4 / 6

www.ro
y
alcraft.co.uk
Step by step assembly instructions
Step One
Align Backrest (A) with Right Armrest/Leg (D).
Carefully insert the tubular mating part of
Right Armrest/Leg (D) into the end of
the tube on Backrest (A).
Connect the Backrest (A) and Right Armrest/Leg (D)
using Washers (F3) and Bolts (F63).
Make sure all bolts are in place and turn freely.
At this stage, don’t tighten the bolts.
Step Two
Repeat above steps for Left Armrest/Leg (C) as shown.
Step Three
Place the sub assembly from above onto
Front Leg (B) as shown.

Cannes KD Carver Chair incl.
cushion
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 5 / 6

www.ro
y
alcraft.co.uk
Step Four
Turn the partly-assembled chair upside down.
Locate assembly holes, connect all parts
using Washers (F3) and Bolts (F63).
Make sure all bolts are in place and turn freely.
At this stage, don’t tighten the bolts.
Step Five
Turn the partly-assembled chair to the upright
position. Push Seat Panel (E) into place as shown.
Step Six
Turn over the partly-assembled chair.
Fix the Seat Panel (E) in place using
Washers (F3) and Bolts (F63).
Once you are satisfied with the alignment
of all components, carefully tighten all bolts
using Spanner (F1).
Do not over-tighten.
Cover each Bolt Head with Bolt Head Cap (F2).

Cannes KD Carver Chair incl.
cushion
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 6 / 6

www.ro
y
alcraft.co.uk
Step Seven
Level the chair with pre-fitted adjustable foot.
Step Eight
Place the Seat Cushion (F) onto the Seat Panel (E).
Your chair is now ready for use.
Never tilt the Chair during use.
Ensure the product is always placed firmly
on the ground.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Adjustable Foot 