Royalcraft Rio Black Glass Table User manual

Product size:
W96.5*O96.5*H70cm
a 
 a  
  
  
 a 
 
The intended use of this product is for domestic use only.
Important, please retain for future reference.
Read carefully .
 
   
   1 / 5

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 2 / 5
www.ro
y
alcraft.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure tofollow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Do not stand or climb onto this product.
This product is intended for domestic use only.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Removing all packaging and banding and place the components
carefully on suitable surfaces to prevent damaging or scratching
them.
Check the pack and make sure you have all of the parts listed.
Check all screws and bolts are tightened and inspect regularly.
This product is suitable for all year outdoor use.
However to prolong its life we recommend that during severely
bad weather and during the winter months, it is stored in a cool,
dry place.
Before storage, ensure that the product is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipewitha clean, dry cloth.
Don’ts
Do not use scourers, abrasives, washing powders, chemical
cleaners or any other substances containing abrasives sincethe
substances can damage the product, including the glass panel.
Do not place very hot or very cold items on the glass surface
unless adequately thick table-mats are used to prevent such
items from coming into contactwith the glass.
Do not use the glass as a chopping surface. Do not strike glass
with hard or pointed items.
Do not strike the glass with hard or pointed items.
Do not use power tools to construct this product.
Do not use this product if parts are missing, damaged or worn.
Do not sit or lean on this product.
Do not stand or climb onto the product and do not use it as a
ladder, as this could lead to it unbalancing and overturning.
Never drag furniture when moving it, always lift it.
Number of people required for assembly
Two people
Time to assemble
30 Minutes
Tools required
Tips:
Do NOT fully tighten bolts before
all components are connected.
Only fullytighten once you are
satisfied with the alignment of all
components.
Do not over-tighten the bolts.
Rio 96.5cm Black Glass Table
Assembly instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 3 / 5
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
A
Table Top
1 PC B
Table Leg
4 PCS
C
Upper Connecting
Ring
1 PC D
Bottom Connecting
Ring
1 PC
E
Bolt Head Cap
8 PCS F
M6*50mm Bolt
8 PCS
G
Washer
8 PCS H
Nut
8 PCS
I
Nut Cap
8 PCS J Parasol Hole Cap
(Pre-Assembled)
1 PC
K
Allen Key
1 PC L
Spanner
1 PC
Rio 96.5cm Black Glass Table
Assembly instructions
www.royalcraft.co.uk

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 4 / 5
www.ro
y
alcraft.co.uk
Step by step assembly instructions
Note: Tighten only enough to hold parts in place. Do not tighten completely during assembly.
Some adjustments may be necessary to ensure all parts are aligned properly.
Only tighten the bolts when all bolts and washers are in place.
Step One
With the help of another person, place
Table Top (A) upside down on a flat,
non-abrasive surface to avoid scratching
the table surface or rim.
Locate the assembly position on
the bottom side of the Table Top (A).
It is a plastic socket.
Attach the Table Legs (B)
onto the assembly position.
Step Two
Place the Upper Connecting Ring(C)
onto the Table Legs (B), using
Bolt Head Caps (E), Bolts (F),
Flat Washers (G), Nuts (H) and
Nut Caps (I).
Once you are satisfied with the alignment
of the components, carefully tighten
all bolts using Allen Key (K) and
Spanner (L). Do not over-tighten.
Cover each bolt with Bolt Head Cap (E).
I
H
G
F
E
A
B
C
C
A
A
BB
B
B
Rio 96.5cm Black Glass Table
Assembly instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 5 / 5
www.ro
y
alcraft.co.uk
Step Three
Place the Bottom Connecting Ring (D)
onto the Table Legs (B), using
Bolt Head Caps (E), Bolts (F),
Flat Washers (G), Nuts (H) and
Nut Caps (I).
Once you are satisfied with the alignment
of the components, carefully tighten
all bolts using Allen Key (K) and
Spanner (L). Do not over-tighten.
Cover each bolt with Bolt Head Cap (E).
Step Four
With the help of another person,
carefully turn over the table and
place it in the upright position.
Make sure there is no wobbling
when the table is placed on
the flat ground.
Your table is now ready for use.
Note: When using a parasol with this table always use a suitable base weight.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
I
H
G
F
E
D
B
Rio 96.5cm Black Glass Table
Assembly instructions