Equipment must be correctly mounted so that the main terminal of AnyTouch will not be touched inadvertently.
Otherwise, an accident or electric shock may occur.
Tighten the fixtures of the AnyTouch with a torque in the specified range. Excessive tightening may distort the
panel surface. Loose tightening may cause AnyTouch to come off, malfunction or be short-circuited.
Check periodically that terminal screws on the power supply terminal block and fixtures are firmly tightened.
Loosened screws may result in fire or malfunction.
Tighten terminal screws on the power supply terminal block equally to a torque of 0.5 N m. Improper tightening of
screws may result in fire, malfunction, or trouble.
AnyTouch has a glass screen. Do not drop or give physical shock to the unit. Otherwise, the screen may be
damaged.
Connect the cables correctly to the terminals of AnyTouch in accordance with the specified voltage and wattage.
Over-voltage, over-wattage or incorrect cable connection could cause fire, malfunction or damage to the unit.
Be sure to establish a ground of AnyTouch. Ground FG terminal which must be used for the unit. Otherwise,
electric shock or a fire may occur.
Prevent any conductive particles from entering into AnyTouch. Failure to do so may lead to fire, damage or
malfunction.
Do not attempt to repair, disassemble or modify AnyTouch at your site. RS Automation Co., Ltd. is not responsible
for any damages resulting from repair, overhaul or modification of AnyTouch that was performed by an
unauthorized person.
Do not use a sharp-pointed tool when pressing a touch switch. Doing so may damage the screen.
Only experts are authorized to set up the unit, connect the cables or perform maintenance and inspection.
The combustible materials such as lithium or organic solvent contained in the battery may generate heat, explode,
or catch fire, resulting in personal injury or fire. Read related manuals carefully and handle the lithium battery
correctly as instructed.
Do not press two or more points on the screen at the same time. If there is a switch between the two pressed
points, it may be activated.
Take safety precautions during such operations as setting change during running, forced output, start, and stop.
Any misoperation may cause unexpected machine motions, resulting in machine accident or damage.
In facilities where a failure of AnyTouch could lead to accident threatening human life or other serious damage, be
sure that the facilities are equipped with adequate safeguards.
At the time of disposal, AnyTouch must be treated as industrial waste.
Before touching AnyTouch, discharge static electricity from your body by touching grounded metal. Excessive
static electricity may cause malfunction or trouble.
A LED lamp illuminates (red) during access to the CF card. Do not insert or remove the CF card or turn the power
off on illuminating the LED lamp. Doing so may destroy data on the CF card. Before mounting or removing the CF
card or turn the power off, be sure to check that the light of the LED lamp is turned out.
UL/c-UL Approval
The V715XD+ is UL/cUL-approved. (File No. : E185413(UL60950-1), File No. : E303690(UL1604))
These products conform to the following four standards.
・UL60950-1 Information Technology Equipment - Safety - Part 1: General Requirements
・UL1604 Standard for Electrical Equipment for Use in Class I, Division 2 Hazardous Locations
・CSA-C22.2 No. 60950-1Information Technology Equipment - Safety - Part 1
・CSA-C22.2 No. 213-M1987 Non-Incendive Electrical Equipment for Use in Class I, Division 2 Hazaedous Locations
UL1604/CSA-C22.2 No. 213 Compliance and Handling Cautions
○Power, input and output wiring must be in accordance with Class I, Division 2 wiring methods - Article 501 - 10(B) of
the National Electrical Code, NFPA 70.
○WARNING: Explosion Hazard: Substitution of components may impair compliance to Class I, Division 2.
○WARNING: Explosion Hazard: Do not disconnect while circuit is alive unless area is known to be non-hazardous.
○WARNING: Explosion Hazard: When in hazardous locations, turn off power before replacing or wiring modules.
CE Marking
The V715XD+ complies with EMC directive:
EN55011 Class A, EN61000-6-2
NK Standard
V715XD+ is the product which is certified as NK Standard by NIPPON KAIJI KYOKAI.
Type Test No. : 06A014
