RSI Systems Furniture EZcube User manual

EZcube Installation Guide
RSI Systems Furniture

RSI Systems Furniture
2

3
RSI Systems Furniture
EZcube Installation Guide
4-5
6-8
9-11
12-13
14
15
16
17
Panels
Connection Posts
Top Cap / End Trim
Worksurface Brackets
Support Leg
Shelf
Power Blocks
Duplexes

STEP 3: Grab your X3 Panel Screw (M6x30mm), stick it
through Connector-B and start screwing it into Connec-
tor-A that is mounted inside the connecting panel.
STEP 4: Before fully tightening the bracket make sure the top
and sides of the panels are all lined up.
STEP 2: Determine which side of the panel has Connector-A
and Connector-B
STEP 1: Lift up and remove the fabric tile from one side of
the panel.
Connector-B
(Non-Threaded Connector
Connector-A
(Threaded Connector)
4RSI Systems Furniture
X3 Panel-to-Panel Connection

X1 Panel-to-Panel Connection
5
RSI Systems Furniture
STEP 1: Determine the direction of the interlocking
brackets on each side of the panel.
STEP 2: Lift up the panel you are connecting and lower in on to the interlocking brackets of the panel you are con-
necting to.
STEP 3: While you are connecting you should hear the spring loaded locking bracket snap into place. To ensure a solid connec-
tion lift up slightly on the panel to ensure a solid locked connection

STEP 1: Fit the X31 Post centering pieces into the X3
Panel Rail.
STEP 3: Make sure the top cap line on the X31 Post
lines up with the top of the side rail then nish tight-
ening the post screw.
RSI Systems Furniture
Connector-B
(Non-Threaded Connector
X3 Panel to X31 Post Connection
STEP 2: Feed your X31 Post Screw (M6x20mm) through the
Connector-B bracket and into the post.
NOTE: If you have Connector-A mounted inside the pan-
el you will need to swap them out with the extra Connec-
tor-B brackets that are included in your hardware pack.
6

STEP 3: Lift up slightly on the panel to ensure the panel and post are locked together.
STEP 2: Lift up the panel you are connecting and lower
in on to the interlocking brackets of the X31 Post you are
connecting to.
7
RSI Systems Furniture
X1 Panel to X31 Post Connection
STEP 1: Determine the direction of the interlocking
brackets on each side of the panel.

RSI Systems Furniture
STEP 3: Make sure the bottom top cap line on the
X3 Post lines up with the top of the side rail then n-
ish tightening the screw.
STEP 2: Feed your X3 Ponel Screw (M6x30mm) through the
Connector-B bracket and into the post.
NOTE: If you have Connector-B mounted inside the panel
you will need to swap them out with the extra Connector-A
brackets that are included in your hardware pack.
STEP 1: Fit the X3 Post centering pieces
into the X3 Panel Rail.
X3 Panel to X3 Post Connection
8

9
RSI Systems Furniture
STEP 2: Push the end trim against the panel starting
from the top.
Note: You should hear it start to click into place as
you center it all the way down the panel.
STEP 1: Line up the top of the end trim
with the top of the side rail.
STEP 3: Hold end trim against the panel
rmly then slowly screw end trim into place
using the self tapping screws provided.
Note: Do not over tighten screws.
STEP 4: To connect the corner transition, rst place the
fabric tile on the panel then insert the corner transition
into the top cap and press the top cap down onto the
panel.
Note: For top cap installation instructions see page-xx
X3 End Trim

RSI Systems Furniture
STEP 1: Snap the top cap down at an an-
gle to get it started.
STEP 3: Make sure that the top cap is
completely seated against the top of
panel.
STEP 2: Slowly move down the panel and
snap it into place as you move down to
the end.
X3 Top Cap
10

STEP 2: Unscrew the X1 connecting brackets and
slide up and off the panel
STEP 3: Put the side top cap back on the panel then grab the end trim and
Insert L-Shaped end rst then snap into place
STEP 1: Remove the X1 Panel Side Top Cap
11
RSI Systems Furniture
X1 End Trim

RSI Systems Furniture
STEP 1: Angle the work surface bracket and insert the top tooth into
the Side Rail
STEP 2: Make sure the bracket is completely seated on the side rail
NOTE: The top of the brackets should be installed around 28.5” so
they match up with the support legs.
X3 Support Brackets
12

STEP 4: Slide the loose backplate down the side rail slot with the cantilever attached. Tighten the
screws once you have reached the correct location.
STEP 3: Measure the height on the X3 work surface brack-
ets so you know what height to install the brackets at.
STEP 2: Get the X1 Bracket Screws and screw in the
backplate slightly (do not tighten yet)
STEP 1: Remove X1 Panel Side Top Cap
X1 Support Brackets
13
RSI Systems Furniture

RSI Systems Furniture
Front Edge
Support Leg
STEP 1: Position the leg so it is ush with the front corner edge
of the surface.
STEP 2: Attach one screw to the bottom side of the surface. This
will provide additional support while you attach the surface to
the corner bracket that will be positioned behind the leg.
STEP 3: Slide the leg over and attach the corner bracket to the worksurface. STEP 4: Slide the leg back to its original loca-
tion and attach the remaining screws.
14

15
RSI Systems Furniture
STEP 1: Install the shelf ends to the bottom shelf pan with the screws provided.
STEP 2: Angle the shelf and insert the top tooth into the side
rail.
STEP 3: Make sure the shelf is completely seated on the side
rail
X3 Shelf

Power Block
STEP 1: Lift the cable channel door open to access the
power mounting brackets
STEP 3: Position the power block so it slides onto the existing mounting brackets mounted inside the cable
channel.
STEP 4: Keep sliding until you hear the power block snap into place on the panel.
STEP 2: Remove the duplex covers on the panel sides re-
ceiving duplex receptacles.
RSI Systems Furniture
16

X3 Shelf
STEP 1: Insert the duplexes into the mounted power block
STEP 2: Once inserted, slide the duplexes toward the outer edge until you hear them snap into place
17
RSI Systems Furniture