RTA Techni Mobili RTA-00397B User manual

Imported By
Thank you for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Do not discard this manual or any of the packaging material until the unit
has been completely assembled.
MODEL RTA-00397B
ASSEMBLY INSTRUCTIONS

MAIN PARTS LIST
A
x1 B
x1 C
x1
D
x1
E
x1 F
x1 G
x1
H
x2
Left Leg Keyboard tray
Main Glass Top
Center tube
Left keyboard slider
Top tubes
Right Leg
Size: 43.25”W x 22.5”D
(W1100xD570mm)
Size: 23.5”W x 12”D
(W600xD300mm)
Right keyboard slider
Size: 2”Ø x 37.5”L
(Ø50*955mm)
Size: 0.75”Ø x 41.75”L
(Ø19*1065mm)
HARDWARE LIST:
1
x2 2
x2 3
x2 4 x8
5
x4 7
x2 8
x4
6
x4
80mm 25mm
Connector for tube Ⓖ.End cap for legs
Ø6 Studs for legs
9mm 12mm
9
x4 10 x1
11
x1 12
x1 Hex Key
Cap nuts Allen Key 5mm
P.2
RTA-00397B
P.2
Allen Key 4mm
(To use with screws #3)

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
P.3
RTA-00397B
P.3
❶Do a quick inventory to
make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged and
defective parts can be
replaced at no cost to you.
Please refer to the CONTACT
card included with the product.
❸The replacement parts service
is limited to the continental United
States. If you reside in Hawaii,
Puerto Rico, U.S. Dependencies
or other countries, please contact
the supplier from where the unit
was purchased.
❹If during assembly you find
an issue or need clarification,
please contact our Customer
Service for assistance. Please
refer to the CONTACT card
included with the product.
❺On each step read the
instructions and analyze the
illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten or
force the screws as they
might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you understand
which hardware will be used
on each step. Using the wrong
size of screw, bolt or pin might
strip the threads or cause
damage to the part in which it
is being used.
❼To avoid misalignments,
always leave the screws
loose and tighten them until
all pieces are positioned
correctly.
❾Sometimes the laminate might cover partially or
entirely the hole on a panel. If there is no visible hole for
the screw, pass and press the tip of your finger over the
area where the hole should be located to feel the
indentation, and once found, carefully pierce the laminate
to reveal the hole underneath.
❿If the hole seems too small for the screw, first make
sure you are using the correct size of screw and that it’s
been installed in the correct hole. If the hole still appears to
be too small, carefully pierce the laminate to reveal the
hole’s actual size. √

P.4
RTA-00397B
P.4
ASSEMBLY STEPS
Inert the studs ⑧into the bottom of the legs Ⓐand Ⓑ.
Assemble the center tube Ⓖto the leg Ⓐusing screw ③and washer ⑦, with connector
①in between the leg and the tube as shown.
STEP 2
Hardware/Tools:
❶
1
Pc
❸
80 mm
1
Pc
❼
1
Pc
❿
5 mm
STEP 1
Hardware/Tools:
❽
4
Pcs
ⒶⒷ
Ⓐ
Ⓖ
①

P.5
RTA-00397B
P.5
Assemble the top tubes Ⓗto the leg Ⓐusing screws ④.
First place the connector ①in between the leg Ⓑand the center tube Ⓖ. Then assemble
the leg Ⓑto the tube Ⓖusing screw ③and washer ⑦. Finally, assemble the leg to the
tubes Ⓗusing screws ④as shown.
STEP 3
Hardware/Tools:
❹
25mm
2
Pcs
❿
5mm
Ⓗ
Ⓗ
Ⓐ
STEP 4
Hardware/Tools:
❶
1
Pc
❸
80 mm
1
Pc
❹
25 mm
2
Pcs
❼
1
Pc
❿
5 mm
⓫
4 mm
Ⓖ
①
Ⓗ
Ⓗ
③
④
④
Ⓑ
Ⓑ
Ⓖ
FIRST!
⑦
(Internal view)

P.6
RTA-00397B
P.6
Insert the end caps ②into the center of the legs Ⓐand Ⓑ.STEP 5
Hardware/Tools:
❷
2
Pcs
Ⓐ
Ⓑ
Assemble the keyboard sliders Ⓔ(Left side) and Ⓕ(right side) to the top tubes Ⓗusing
screws ④(inserted from above) and cap nuts ⑨(attached from below) as shown.
STEP 6
Hardware/Tools:
❹
25 mm
4
Pcs
❾
4
Pcs
⓫
4 mm
⓬
Ⓔ
Ⓕ
(Left)
(Right)
Ⓗ
Ⓗ
Screw from above,
Nut from below.

P.7
RTA-00397B
P.7
Place the keyboard tray Ⓒover the tabs of the sliders Ⓔand Ⓕand assemble it using
screws ⑥from underneath as shown.
STEP 8
Hardware/Tools:
❺
9mm
4
Pcs
⓫
4mm
Ⓒ
Ⓔ
Ⓕ
STEP 7
Hardware/Tools:
❻
12mm
4
Pcs
(NOT INCLUDED)
DONE! Before you start using the unit, make sure that all the screws, bolts, cam locks, etc. are properly
tightened, and read all the warnings in the next page.
Pay attention to the orientation of the panel
Ⓓ
Ⓑ
Ⓐ
Carefully place the glass top Ⓓover the frame making sure the round metal disks on the
glass coincide with the holes on the legs Ⓐand Ⓑ, and assemble it using screws ⑤from
underneath as shown.
Tip: Adjust the studs to help
leveling the unit on the floor.

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferably with a clean cloth damped in a solution of mild soap and water, then dry with a
clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the tabletop.
•Do not seat on the unit or lean against it.
•Do not allow small children to play under or over the unit.
•The unit must be handled by at least 2 persons when moving in the same or adjacent rooms.
•Before moving the unit, make sure to remove any object that is heavy or might fall off.
•Lift the unit from the frame, use both hands and bend your knees, not your backs.
•When transporting the unit to places far away, protect and secure it to avoid damage in transit.
•The glass is made of safety tempered glass. The safety feature is that when breakage occurs, the glass
shatters into many tiny pieces minimizing the risk of serious injuries. If the glass breaks, do not handle the
pieces with your bare hands, take some pictures and contact Customer Service immediately. Please refer to
the Contact Us card.
•Shall
any part of the unit become defective during the warranty period, replacement parts might be available to
you at no charge. Please refer to the WARRANTY card included with the product.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages or
consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not heeding
the above warnings.
•The warranty is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
Dependencies or other countries, please contact the supplier from where the unit was purchased.
P.8
RTA-00397B
P.8
WEIGHT LIMITS
Glass top:
110 Lbs. (50 Kg)
Keyboard tray:
22 Lbs. (10 Kg)