RTA Techni Mobili RTA-2018 User manual

By
Thank you for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Do not discard this manual or any of the packaging material until the unit has
been completely assembled.
MODEL RTA-2018
ASSEMBLY INSTRUCTIONS
☛ Assembly video also available online at technimobili.com
With adjustable shelf

Left structure Right structure Locking Caster Non-Locking Caster
Back panel Lower panel
Main panel Keyboard slider SET Keyboard panel
Printer/Monitor panel CD holder Support tube Protection
clip
Screw knob
MAIN PARTS LIST
P.2
RTA-2018
P.2
❶
x1 ❷
x2
❸
x1 ❹ x1
❺
x1 ❻ x1 ❼ x1
❽
x1 ❾ x1 ❿
x2
10A 🅛
x2
10C
❶
x1
⓫
x2
10B
1L 1R ❷
x2
2L 2N
MAIN PARTS LAYOUT (For reference)

SCREWS LIST
P.3
RTA-2018
P.3
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
•Do a quick inventory to make sure the product contains all the parts and hardware.
•
Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card
included with the product.
•The replacement parts service is limited to the continental United States. If you reside in Hawaii, Puerto
Rico, U.S. Dependencies or other countries, please contact the supplier from where the unit was purchased.
•If during assembly you find an issue or need clarification, please contact our Customer Service for
assistance. Please refer to the CONTACT card included with the product.
•On each step read the instructions and analyze the illustrations thoroughly before proceeding to do the
assembly.
•Make sure you understand which hardware will be used on each step. Using the wrong size of screw, bolt or
pin might strip the threads or cause damage to the part in which it is being used.
•To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned
correctly.
•Do not overtighten or force the screws as they might break, strip, damage the threads of the holes or get
stuck inside the part.
•Sometimes the laminate might cover partially or entirely the hole on a panel, but the hole should still be
located under the laminate.
•If there is no visible hole for the screw, pass and press the tip of your finger over the area where the hole
should be located to feel the indentation, and once found, carefully pierce the laminate to reveal the hole
underneath.
•If the hole seems too small for the screw, first make sure you are using the correct size of screw and that it’s
been installed in the correct hole. If the hole still appears to be too small, carefully pierce the laminate to
reveal the hole’s actual size.
PART QTY SIZE /
DESCRIPTION FIGURE
🅐4 6x45mm
🅑8 6x30mm
🅒6 6x12mm
🅓8 4x12mm
1Hex Wrench
1
Allen Wrench
Hex/Phillips

ASSEMBLY STEPS
P.4
RTA-2018
P.4
Using the wrench, assemble the casters ②to the structures ①L, ①R in the following
order:
☛The locking casters ②L go on the front bottom holes,
☛The non-locking casters ②N go on the back bottom holes.
First check and make sure of the correct alignment of the inserts in the back panel ③, then
use screws Ⓐto assemble it to the structures ①Land ①R as shown.
If the inserts are misaligned,
use a flat head screwdriver
to re-align them.
STEP 1
STEP 2
Screws:
Ⓐ
6x45mm
4
Pcs
L
N
Panel ③comes with metal inserts on its interior face, they look like screws but are nuts
pre-aligned to receive the screws. Sometimes misalignments occur, and you will have to use
a flat head screwdriver (not included) to turn and align the inserts as shown below.
YES √NO XThe middle and
lower bars face
towards the inside.
Locking at front
Non-locking at back

P.5
RTA-2018
P.5
STEP 3
Screws:
Ⓑ
6x30mm
4
Pcs
Use screws Ⓑto assemble the lower panel ④to the lower bars on the structures ①L,
①R from underneath as shown.
Use screws Ⓑto assemble the main panel ⑤to the top bars of the structures ①L and
①R from underneath as shown.
STEP 4
Screws:
Ⓑ
6x30mm
4
Pcs
STEP 5
Screws:
Ⓓ
4x12mm
4
Pcs
Use screws Ⓓto assemble the keyboard sliders ⑥on their respective sides to the middle
bars of the structures ①L and ①R from the inside. The screws have to go thru the sliders’
holes and insert into the holes on the structures as shown.
The flat side goes
against the bar
The tabs face down

P.6
RTA-2018
P.6
STEP 6
Screws:
Ⓓ
4x12mm
4
Pcs
Use screws Ⓓto assemble the keyboard panel ⑦to the sliders ⑥from underneath as
shown.
Use screws Ⓒto assemble the CD rack ⑨to either structure ①L or ①R according tp
your preference.
STEP 7
Screws:
Ⓒ
6x12mm
2
Pcs
OR
STEP 8
Screws:
Ⓒ
6x12mm
4
Pcs
Use screws Ⓒto assemble the support tubes ⑩A to the monitor/printer panel ⑧
as shown.
(Front)

P.7
RTA-2018
P.7
STEP 9 Assemble the support tubes ⑩A to the main panel ⑤ in the position of your preference
making sure that the protection clips ⑩B are positioned in between, then use the screw
knobs ⑩C to secure the tubes as shown.
ON THE LEFT: ON THE RIGHT:
ALL DONE! Before you start using the unit, make sure that all the screws, bolts, cam
locks, etc. are properly tightened, and read all the warnings in the next page.
(This view is from the back side)
ON THE BACK:
The clips ⑩B go in between the tubes and
the main panel.

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water,
then dry with a
clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the main
panel.
•Do not seat on the unit or lean against it.
•Do not allow small children to play under or over the unit, nor use it as a moving vehicle.
•Keep the unit with the front casters locked.
•Before moving the unit, make sure to unlock the front casters, and remove any object that might fall off.
•When transporting the unit to places far away, lock the front casters and protect and secure the unit to avoid
damage in transit.
•Shall any part of the unit becomes defective during the warranty period, replacement parts might be
available to you at no charge. Please refer to the WARRANTY card included with the product.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages
or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not
heeding the above warnings.
•The warranty is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
Dependencies or other countries, please contact the supplier from where the unit was purchased.
P.8
RTA-2018
P.8
WEIGHT LIMITS 30 Lbs. (13.60 Kg)
22 Lbs. (9.97 Kg)
100 Lbs. (45.36 Kg)
30 Lbs. (13.60 Kg)