RTA Techni Mobili RTA-325 User manual

MODEL RTA - 325
Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Please save this manual for future reference.

RTA-325
DIMENSIONS
MAXIMUM WEIGHT CAPACITIES
DO NOT exceed this limit
Please use care and good judgement
when placing objects on wood surface
Product Size: 51-1/5"W x 22-1/4"D x 39-3/8"H

P.3
Left Back Panel CPU Tube Screw stud CPU Panel
Short Tube Long Tube Left Panel Right Panel
Right Back Panel Bottom Panel Top Panel Long Support Tube
Short Support Tube Main Table Top Keyboard Slider Slider Base
X3
X2
X1 SET X4

P.4
Keyboard Panel Small Drawer Left
Panel
Small Drawer Right
Panel
Small Drawer Front
Panel
Small Drawer Bottom
Panel
Small Drawer Back
Panel Drawer Slider File Drawer Left
Panel
File Drawer Right
Panel
File Drawer Front
Panel
File Drawer Bottom
Panel
File Drawer Back
Panel
File Drawer Tube Handle Top Glass Top Support Tube
Metal Fitting
X2 SET
X2 X2
X2

P.5

P.7
Grab all the flat shaped Drawer Sliders (23) and set aside the
“L” shaped ones. With the Left & Right Panels (7&8) oriented
as illustrated, assemble one pair of flat sliders (23) to the top
holes on their inside faces. The wheels will be located at the
front and facing down.
Screw the Bolts (B) to the corresponding holes on the inside face of
Top Panel (11), then assemble the Top Panel (11) to the Left & Right
Panels (7&8) by turning all the corresponding cam locks.
First screw the Bolts (B) to the corresponding holes on the inside
face of Right Back Panel (9), then assemble to it the panels (7), (8)
& (11) by turning all the corresponding cam locks. Please pay close
attention to the orientation of all the parts as illustrated.

P.8
Screws the Bolts (B) to the corresponding holes on the inside face
of Bottom Panel (10), then assemble the Bottom Panel (10) to (7),
(8) & (9) by turning all the corresponding cam locks.
Please pay close attention to the orientation of all the parts as
illustrated.
Assemble the other pair of flat sliders to the inside face of the
Left & Right Side Panels (7&8). The wheels will be located at
the front and facing down.
Use Screws (C) to fix the Long Support Tubes (12) to the
underside of the Bottom Panel (10). Screw the Studs (3) to the Long Support
Tubes (12).

P.9
Use Screws (D) to assemble the Short Tube (5) and
Long Tube (6) to the CPU Panel (4) with the plastic
washers (M) in between the tubes and the panel. Then
screw the Stud (3) to the short Tube (5). Please follow
the illustration for the correct assembly order and
orientation of the parts.
Use Screws (E) to assemble the CPU Panel (4) to
the Left Back Panel (1).
Use Screws (F) to affix the CPU Tube (2) to the Left Back
Panel (1) & CPU Panel (4).
Note: If part (2) seems misaligned, or a little too short/long,
unscrew and loosen panel (4) from panel (1) to allow some
flexibility and this will allow part (2) to reach both holes.
Use Screws (C) to affix the Short Support Tube (13) to the
Main Panel (14).

P.10
Use Screws (G) to affix the Slider Bases (16) to the
Main Panel (14).
Use Screws (H) to fix the Keyboard Slider (15) to
the Slider Bases (16) as illustrated. Please note
the position of the tabs on the sliders.
First screw the Bolts (B) to the corresponding holes on the Main Table
Top (14). Then, position both portions of the desk as shown in the
illustration, and while the second person holds the cabinet, assemble
the Main Table Top (14) to the Right Back Panel (9) as illustrated, place
the plastic washer (M) in between the Short Support Tube (13) and the
Top Panel (11), and finally turn the corresponding cam locks. The Long
Tube (6) will hold the table top on that side, and will get assembled in the
follow step.
ATTENTION: A second person is required to assist with this step.