RTI PIKO RGB 20 User manual

Manual / Bedienungsanleitung /
Mode d´emploi
RTI PIKO Series
PIKO RGB 20 | PIKO RGB 22 OPSL
PIKO G 20 OPSL
Please spend a few minutes to read this manual fully
before operating this laser!
Bitte lesen Sie diese Bedienungsanleitung sorgfältig
vor Inbetriebnahme dieses Showlasersystems!
Avant d’utiliser cet appareil pour la première fois nous vous recommandons
de lire cette notice d’utilisation!
11/2018
English
Deutsch
Français

Manual: RTI PIKO Series
page 2 / 57
Rechtlicher Hinweis:
Die Firma Ray Technologies GmbH behält sich das Recht vor, Änderungen an ihren Produk-
ten vorzunehmen, die der technischen Weiterentwicklung dienen. Diese Änderungen werden
nicht notwendigerweise in jedem Einzelfall dokumentiert.
Diese Betriebsanleitung und die darin enthaltenen Informationen wurden mit der gebotenen
Sorgfalt zusammengestellt.
Die Firma Laserworld (Switzerland) AG und ihr Tochterunternehmen, die Ray Technologies
GmbH, übernehmen jedoch keine Gewähr für Druckfehler, andere Fehler oder daraus entste-
hende Schäden.
Die in dieser Bedienungsanleitung genannten Marken und Produktnamen sind Warenzeichen
oder eingetragene Warenzeichen der jeweiligen Titelhalter.
Legal notice:
Thank you for purchasing this Ray Technologies product.
Due to continual product developments and technical improvements, Ray Technologies
GmbH reserves the right to make modications to its products.
This manual and its content have been made with due care but neither Laserworld (Switzer-
land) AG nor its subsidiary Ray Technologies GmbH cannot, however, take any responsibility
for any errors, omissions or any resulting damages forthwith.
The brands and product names mentioned in this manual are trade marks or registered trade
marks of their respective owners.
Information juridique :
L’entreprise Ray Technologies GmbH se réserve le droit d’eectuer des modications con-
cernant leurs produits et ainsi de répondre au développement technique. Ces modications
ne seront pas nécessairement annoncées en tout cas spécique. Ce mode d’emploi et les in-
formations contenues dedans ont été établis avec le soin minutieux qui s’impose dans ce cas.
Laserworld (Switzerland) AG et sa liale Ray Technologies GmbH ne pourra pas être tenue
responsable pour d’éventuelles erreurs d’impression ou dommages en résultants.
En cas de doutes, veuillez toujours contacter Laserworld (Switzerland) AG . Les noms de
marques et de produits utilisés dans ce mode d’emploi sont des marques de fabrique ou des
marques déposées.
L’utilisation est réservée à un usage professionnel selon décret n°2007-665 du 2 mai
2007 relatif à la sécurité des appareils à laser sortant!
Article 4 bis :
« Les usages spéciques autorisés pour les appareils à laser sortant d’une classe supérieure à 2
sont les usages professionnels suivants :
(…)
9° Spectacle et achage :
Toutes les applications de trajectoire, de visualisation, de projection ou de reproduction
d’images en deux ou trois dimensions. »

Manual: RTI PIKO Series
page 3 / 57
Content:
1. Product and package contents
2. Preliminary warning notices
3. Initial operations, safety instructions
4. Working on the device
5. Service notes
6. Warnings and other notices on the device
7. Device connections
8. Operation
9. Remote control pad
Final statement
Technical data sheet
Laser specications

Manual: RTI PIKO Series
page 4 / 57
1. Product and package contents
Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector 1 x manual 1 x powercon power cable
1 x 3-channel adapter (only for RTI PIKO RGB 22)
3. Initial operations, safety instructions
1. Make sure to use correct voltage; see in-
formation on device & in this manual.
2. Make sure that the device is not connec-
ted to mains during installation.
3. Installation has to be done by technical
experienced and qualied persons ac-
cording to safety regulations of the res-
pective country.
4. Always ensure that maximum permis-
sible exposure (MPE) is not exceeded
in areas accessible to the public or
members of sta.
5. In some countries an additional ins-
pection by technical control institutes
could be necessary.
6. The power supply should be easily acces-
sible.
7. When installing the laser mount it with
a minimum distance of 15 cm from walls
and objects.
8. For safe setup e.g. on walls or ceilings
please use a safety cord. The safety cord
should be able to withstand tenfold the
weight of the device. Please follow the
accident prevention regulations of pro-
fessional associations and/or comparable
regulations for accident prevention.
9. If the device has been exposed to great
temperature changes, do not switch it
on immediately.
10. Never use dimmer, RC or other electroni-
cally switched sockets. Whenever possib-
le, do not use the laser projector together
with large appliances (especially fog ma-
2. Preliminary warning notices
1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels,
power supplies or power cords.
3. Never look directly into the light source of a laser projector. Danger of damage to the
eyes or even blindness in extreme circumstances!
4. Do not operate the device at high humidity, in the rain or in dusty environments.
5. Protect device against dripping or splashing water. Do not place any liquid lled
containers near to this device.
Any warranty claims are void if the warranty label is removed or tampered
with in any way.

Manual: RTI PIKO Series
page 5 / 57
chines) on the same mains!
11. Ensure sucient ventilation and do not
place the device on any warm or heat
radiating surface. Especially the venti-
lation openings must not be covered!
12. Ensure that device does not get over-
heated. Make sure that the device is not
exposed to spotlights (especially moving
heads). Heat of spotlights could overheat
laser in a little while and leads to a de-
graadation.
4. Working on the device
1. This product has no user serviceable parts inside and should only
be maintained and serviced by a qualied engineer.
2. Be sure that the mains plug is not connected to the power
supply while installing the device.
3. Take o all reecting things like rings, watches etc. befo-
re starting to work with or at the projector.
4. Only use non-reecting tools to work on device.
5. Wear protective clothing (like goggles, gloves etc.) according to laser power
and wavelength of the laser.
5. Service notes
• Moisture and heat can reduce lifetime of
the laser system dramatically and expires
any warranty claim.
• Quick on/o switching of this device will
reduce durability of the laser diode dra-
matically.
• Avoid sharp knocks and shocks to this
device and ensure sucient protection
during transportation. Look after your La-
serworld product.
• To increase durability of your laser,
protect device against overheating:
-Always ensure sucient ventilation.
-Do not face spotlights (especially mo-
ving heads) to the device.
-Check temperature after approx. 30
minutes with each new installation.
If necessary install the projector at a
place with dierent temperature.
-Keep the device dry. Protect it from
moisture, rain and damp.
-Switch o device when it is not nee-
ded. Diodes are switched on and can
wear out even if there is no visible la-
ser output.
• Please ensure the fans and heatsinks are
clear from dust and debris otherwise the
risk of overheating may occur. If the unit
and airways appear to be blocked then
please contact a qualied service engi-
neer to maintain and service the product.
•Removal of the warranty label as well
as damages to the device caused by
improper handling, neglect of the sa-
fety instructions and service notes will
void the warranty.

Manual: RTI PIKO Series
page 6 / 57
7. Device connections
Mains connection
ILDA in
Interlock out
conguration
Emission LED
DMX out (optional)
DMX in (optional)
6. Warnings and other notices on the device
Laser radiation!
Avoid exposure
to beam.
Laser class 4
Caution of
radiation if cover
is removed
Power supply
& consumption
Model type
Wavelength
Output power
Production
year
Please read manual before operation
Only for indoor use!
Fuse 4At
ILDA out
Interlock in

Manual: RTI PIKO Series
page 7 / 57
8. Operation
Please note that when the ‘Emission LED’ is on, the laser is enabled and may emit laser light.
There is one LED on the remote control pad, one on the rear side and one on the front side of
the device. The LED on the device ashes if the device is connected to the power supply. The
LED on the control pad ashes if the device is switched on.
8.1. Powers supply
Make sure that your device is provided with the correct voltage. Wrong voltage could lead to
irreparable damages. Please nd the correct voltage data in the synoptical table at the end
of this manual. It must be ensured that the device is not directed to people or inammable
objects during installation.
8.2. ILDA control
To control your device connect it via ILDA cables to an interface/controller. The pinout and
maximum voltages for the ILDA standard Sub-D connectors are:
Pin Signal Voltage
1 X + (horizontal) + 5.0 V
2 Y + (vertical) + 5.0 V
4 Interlock A -
5 Red + + 2.5 V
6 Green + + 2.5 V
7 Blue + + 2.5 V
8 (RTI PIKO RGB 22) Light Red2+ + 2.5 V
9 (RTI PIKO RGB 22) Cyan+ + 2.5 V
13 Shutter + 5.0 V
14 X – (horizontal) - 5.0 V
15 Y – (vertical) - 5.0 V
17 Interlock B -
18 Red - - 2.5 V
19 Green - - 2.5 V
20 Blue - - 2.5 V
21 (RTI PIKO RGB 22) Light Red2- - 2.5 V
22 (RTI PIKO RGB 22) Cyan- -2.5 V
25 Ground -

Manual: RTI PIKO Series
page 8 / 57
8.3. Channels (RTI PIKO RGB 22 / RTI PIKO Rainbow Series):
8.3.1. 3-Channel Adapter
This adapter is required to operate the 5 or 6 color channel laser system with an interface
which otherwise supports only 3 color channels. If there are only 3 output channels instead
of 5 or 6, this adapter is required to get the full power of the laser system.
In case you are using a controller with just three color outputs (RGB) you can use the provi-
ded D-Sub connector to wire both red together and blue and cyan together.
You just need to plug the connector into the ILDA OUT plug.
Important: If you are using this D-Sub connector you cannot use controllers with more than
three channels. Otherwise the controller hardware would pull down the intensity of red and
blue! If you have a controller with more than three channels you need to patch the colors in
the software and should not use this D-Sub connector.
Channel Colors / Wavelengths:
1 658nm
2 530nm
3 447nm
4 638nm
5 462nm
The above table shows the assignment of the channels with red and blue. Only the rst thr-
ree channels are occupied by RGB, the remaining three channels can be used freely.
8.3.2. External Interlock
The Remote Control Pad has a built-in emergency stop. If there is the need for an external
interlock, please disconnect the Remote Control Pad and use the ‚Control‘ connection (RJ-45
connector) to connect it with an external interlock.
8.4. Browser operation instructions
The RTI PIKO laser series can be congured via browser over LAN / WiFi. This is possible through
computer, laptop, but also through mobile phones or tablets, if the control signal is sent over
WiFi via a WiFi capable Router / Access Point. Devices connected to the same local network as
the laser systems are capable to accessing the dedicated laser user interface through a previ-
ously congured IP address or an automatically assigned IP address from a DHCP server.
If only one single laser shall be congured and the laser system is directly connected to the
control computer by LAN cable, please continue with chapter 8.1.2.1.

Manual: RTI PIKO Series
page 9 / 57
8.4.1. DHCP mode - automatic address setting
Requirements: Standard router with DHCP functionality (e.g.: D-Link Wireless AC750 DualBand Easy
Router).
The DHCP mode can be used for the conguration of one or more laser devices.
a. Connect the laser device(s) to the router with an ethernet cable (CAT-5 or higher). Make
sure that DHCP mode is activated on the router and that it is capable to provide an auto-
matic IP address ( see the manual of your router ).
b. Connect the router to the computer or the laptop with another ethernet cable (CAT-5 or
higher). It can be possible that the WiFi mode of a compatible router is also instantly ac-
cessible. In this case it can be possible, that mobile devices can already be used without
the need of preliminary conguration through a wired setup. To ensure everything works
well it is recommended to set up a wired conguration rst.
This is how the setup looks like. It is also possible to connect several RTI PIKO lasers to
one router:
Connection with DHCP router
RTI PIKO laser
Ethernet cable
Ethernet cable
Computer
Router
c. Type the IP address or name of your router into the web browser of your computer to
access the administration menu of the router setup. Please see the manual of the router to
nd out how this feature can be accessed. The administration interface of the router usually
has a certain user interface showing all connected devices within the network. Check for
the IP addresses that have been assigned per laser system and write them down for fu-
ture use. Each laser can be congured by entering this IP address to the browser address
bar.
d. If there are no laser units visible on this overview page, make sure that each laser is pow-
ered up properly, that the ethernet cables are connected correctly and that only standard
network cable were used (do not use cross cable!).
e. If it is not possible to access the router administration interface or if the LAN con-
nection shows errors, continue with chapter 8.4.2„How to set the computer to DHCP
mode“

Manual: RTI PIKO Series
page 10 / 57
8.4.2. How to congure the computer to work in DHCP mode
Only follow these steps if issues with accessing the router through DHCP arise.The chapter can
be skipped if the computer can already communicate through DHCP and there is access to the
router administrative menu.
a. Click on the Windows start button and navigate to the control panel, click on„Network
and Internet“ and nd „Network and Sharing center“, click on it. There should be only
one active connection, otherwise deactivate second active connection as it may lead to
irritations. Double click on the active connection name (after label„Connections:“)
b. The„Ethernet Status“ window opens. Click on„Properties“, and head for the „Internet Pro-
tocol Version 4 (TCP/IPv4)“. Double click it and select„Properties“. The following window
allows for setting the DHCP mode. If you want to enable DHCP, make sure„Obtain an IP
address automatically“ is selected, as well as„Obtain DNS server address automatically“.
1
2
3
4
After having done the settings, try the steps described in chapter 8.4.1 again.

Manual: RTI PIKO Series
page 11 / 57
8.4.2.1. Static IP mode
Depending on the number of laser systems that shall be used, there are two options for
connecting the computer to the laser. If only one laser system shall be used, a normal direct
network cable between the laser system and the computer is sucient. This can of course be
extended with a normal switch. This option is discussed in chapter 8.4.2.1. (a).
The other option is that there are more than two laser systems, that shall be connected to the
computer at the same time. To nd more details on this kind of setup, please head to chapter
8.4.2.1. (b).
a. Direct connection
RTI PIKO laser Computer
192.168.1.100 192.168.1.123
Ethernet cable
e.g.
Laser device as RTI PIKO has it‘s own default IP adress 192.168.1.00. In order to establish the
connection, connect the laser device through the ethernet cable directly with the laptop or
PC.
The computer must be set to a static IP address in the same address space than the RTI PIKO
laser , but it MUST NOT be the same IP address, for example 192.168.1.10 or 192.168.1.35 are
OK. See chapter 8.4.2.2 on how to set IP address for the PC properly.
After setting the unique IP at your computer, use previously set IP address to access the laser
conguration panel by typing it to the browser address bar of the computer or any other
(mobile) device that is properly connected to the same local area network as the RTI PIKO la-
ser system. The factory default is: 192.168.1.00. In order to access the browser interface type
default login and password (Login: admin, Password: admin). It is recommended to change
the default login and password to prevent unauthorised access.
In order to change the default IP address of the laser device, connect to the user panel as
described above. Click on the tab„More“ and then on the word „System/IP Setup“ in the user
panel in order to change the static IP address. This IP address has NO EFFECT if the laser is
connected through DHCP (as described in chapter 8.1.1) To change IP address, click here.

Manual: RTI PIKO Series
page 12 / 57
b. Connection through switch
Requirements: Standard network switch
The computer must be set to a static IP address in the same address space than the RTI PIKO
laser(s), but it MUST NOT be the same IP address, for example 192.168.1.10 or 192.168.1.35 are
OK. See chapter 8.4.2.2. on how to set IP address for the PC properly.
In case of having more than one RTI PIKO laser in the local network, ensure to set a unique IP
address for each one of them. To do so, it is necessary that each laser is directly connected to
the computer as described in chapter 8.1.2.1. (a). After having set individual IP addresses per
laser, all lasers and the computer can be wired as shown below:
Switch
Ethernet cable
Ethernet cable
RTI PIKO laser 1 Computer
Ethernet cable
RTI PIKO laser 2
8.4.2.2. How to set a static IP address
a. Click on the Windows start button and navigate to your control panel, click on„Network
and Internet“ and nd „Network and Sharing center“, click on it. There should be only one
active connection, otherwise deactivate the second active connection as it may lead to
irritations. Double click on the active connection name (after label„Connections:“)
b. The„Ethernet Status“ window opens. Click on„Properties“, and look for the „Internet
Protocol Version 4 (TCP/IPv4)“. Click and select„Properties“. The following window allows
for specifying a static IP address. Subnet mask is 255.255.255.0 (do not change).

Manual: RTI PIKO Series
page 13 / 57
1
2
3
4
8.4.3. Browser interface
In the upper left corner of the browser interface it is possible to switch between the dierent
operation statuses: As standard, the laser is„OFF“. To get any output from the system, it is
necessary to change the status to„ON ILDA“.
Laser„OFF“ button. Laser„On ILDA“ button.

Manual: RTI PIKO Series
page 14 / 57
8.4.3.1. Color intensity
This tab allows for changing the color intensity per color channel by sliders.
8.4.3.2. Device status
The„Status“ tab shows selected statistics on the projector status like temperature values,
interlock status as well as XY galvo positioning.

Manual: RTI PIKO Series
page 15 / 57
8.4.3.3. User access conguration
The„User Setup“ tab provides options for changing, adding or deleting users as well as chan-
ging the users passwords.
8.4.3.4. Load rmware updates / conguration
The„Firmware/Cong“ tab allows to upgrade an existing rmware.

Manual: RTI PIKO Series
page 16 / 57
8.4.3.5. Advanced settings
The„Advanced“ tab allows for setting various projector features like safety behavior etc.
8.4.3.6. Scanner settings
The size as well as the position of the projection can be adjusted with the horizontal faders.
Shift species the oset position, Size species the scale of the projection on X and Y axis. It
is also possible to ip the projection by using negative values.

Manual: RTI PIKO Series
page 17 / 57
9. Remote Control Pad (optional available)
If the device is equipped with the optional detachable remote control pad, the following ima-
ges explain the use of the pad. Touch the screen to change the settings.
9.1. Starting sequence
9.2. Main Menu
Emergency Stop
button:
Press button to inter-
rupt laser output
Emission Laser on button:
The device is enabled if the
diode is lit.
Touchscreen
Key switch with key:
Insert key and turn it to
‚on‘ to start the device.
Laser on / o:
Device is enabled /
disabled
Version and tempera-
ture display
Laser status, amperage
& interlock status
display
Laser on / internal:
The internal access
to an e.g. SD-card is
enabled
Laser on / ILDA in:
The external access
through ILDA is ena-
bled
Color & Scan Setup:
Use these buttons for co-
lor or scan settings
DMX, Adv. and Setup:
Use these buttons for the
color or scan settings.
Adv. Setup only for factory
defaults!
Back:
Use this button to return
back.
Status display

Manual: RTI PIKO Series
page 18 / 57
9.3. Color Settings:
+ / -:
Use these buttons to
change the color
intensity
Colors:
Please note that
only implemented laser
sources can be changed in
their itensity. If there is e.g.
no yellow laser source in-
stalled in your device you
can‘t change the itensity
of the yellow color.
The intensity change
only applies per single
laser source and does
not change mixed colors.
Please use your software
to change mixed color in-
tensities.
In case you have a RTI PIKO RGB 22 (RTI PIKO Rainbow Series) you can adjust the light red intensity with the yellow slider
and the cyan intensity with the light blue slider.
9.4. Scanner Settings:
X Size horizontal:
Use these buttons to
change the horizontal
size of the output
Y Size vertical:
Use these buttons to
change the vertical size of
the output
Y Shift up/down:
Use these buttons to
change the vertical shift
of the output
X Shift left/right:
Use these buttons to
change the horizontal
shift of the output

Manual: RTI PIKO Series
page 19 / 57
Final statement
RTI products are tested and product packaging is inspected before leaving our warehouse.
Users must to follow the local safety regulations and warnings within this manual and adhere
to any regulations within its place of use. Damages through inappropriate use will void any
liability or warranty of our products.
Due to continual product developments, please check for the latest update of this product
manual at www.laserworld.com. If you do have any further questions, then please contact
your dealer/place of purchase or use our contact section on our website.
For service issues, please contact your dealer/place of purchase and ensure only genuine
Laserworld spare parts are used in any service repairs.
Errors and Omissions excepted and products are subject to change.
Laserworld (Switzerland) AG
Kreuzlingerstrasse 5
8574 Lengwil
Switzerland
Registered oce:
8574 Lengwil / Switzerland
Company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
CEO: Martin Werner
VAT no. (Switzerland): 683 180
UID (Switzerland): CHE-113.954.889
VAT no. (Germany): DE 258030001
WEEE-Reg.-No. (Germany): DE 90759352
www.laserworld.com
[email protected]
representative according to EMVG:
Ray Technologies GmbH
Managing Director: Martin Werner
Mühlbachweg 2
83626 Valley / Germany

Manual: RTI PIKO Series
page 20 / 57
Inhaltverzeichnis:
1. Lieferumfang & Hinweise
2. Einleitende Warnhinweise
3. Schritte zur Inbetriebnahme, Sicherheitshinweise
4. Sicherheitshinweise für Arbeiten am Gerät
5. Pege- und Wartungshinweise
6. Warnhinweise und Spezikationen am Gerät
7. Geräteanschlüsse & Bedienelemente
8. Bedienung
9. Remote Control Pad
Abschließende Erklärung
Technische Daten
Laserleistungsdaten