Ruijie Networks RG-S2910C-24GT2XS-P-E Installation and operating manual

RG-S2910XS-E Series Switch
Hardware Installation and Reference Guide V1.14

Copyright Statement
Ruijie Networks©2018
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this document,
in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: http://caseportal.ruijienetworks.com
Community: http://community.ruijienetworks.com
Technical Support Email: [e-mail]
Skype: [email protected]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or
loss of data.

1 Product Overview
The RG-S2910XS-E series switch is a next-generation intelligent switch that features high performance, high security,
multiple services and ease of use to meet the needs of the current networks. The RG-S2910XS-E series switch can
provide the complete end-to-end Quality of Service (QoS), flexible and abundant security policies and policy-based
network management for various networks. It is greatly ideal for such applications as campus network, enterprise network,
government network, service network, residential broadband access and business building network, providing high-speed,
high-efficiency, secure and intelligent access solutions.
Table 1-1 RG-S2910XS-E
Model
10/100/1000
Base-T
Auto-sensing
Ethernet Port
SFP+
Port
1000Base-X
SFP Port
Console
Port
USB
Port
Expansion
Module
Slot
Pluggable
Power
Slot
RG-S2910-24GT4XS-E
24
4
1
1
N/A
N/A
N/A
RG-S2910-48GT4XS-E
48
4
1
1
N/A
N/A
N/A
RG-S2910C-24GT2XS-P-E
24 (PoE+)
2
2 (Combo)
1
N/A
1
N/A
RG-S2910C-24GT2XS-HP-E
24 (PoE+)
2
2 (Combo)
1
1
2
Dual
RG-S2910C-48GT2XS-HP-E
48 (PoE+)
2
2 (Combo)
1
1
2
Dual
The SFP+ ports support both 10Gbase-R and 1000base-X modules.
The SFP ports support both 1000 base-X and 100base-X modules.
1000Base-T is compatible with 100Base-TX and 10Base-T in the downlink direction.
1.1 RG-S2910-24GT4XS-E
Technical Specifications
Model
RG-S2910-24GT4XS-E
CPU
Single-core CPU with the clock speed of 1.0G
BOOTROM
/
Flash Memory
256MB
SDRAM
DDRIII 512MB
Optical Module
See Appendix B.
The supported module type may change at any time. Consult us for the latest information.
SFP+ Port
Supports 10Gbase-R and 1000Base-X SFP+ modules.
Power Supply
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency: 50/60 Hz
Rated current: 1.5A

HVDC input
Voltage range: 192V to 290V
Current range: 0.1A to 0.5A
Earth Leakage
Current
≤3.5mA
EEE
Supported
PoE
Not supported
Power
Consumption
≤24W
Operating
Temperature
0ºC to 50ºC (32ºF to 122ºF )
Storage
Temperature
-40ºC to 70ºC (-40ºF to 158ºF )
Operating Humidity
10% to 90% RH
Storage Humidity
5% to 95% RH
Fan
Speed adjustment and fault alarm
Temperature
Warning
Supported
EMCStandards
GB9254-2008
Security Standards
GB4943-2011
Dimensions
(W x D x H)
443mm x 268mm x 44.5mm
Weight
≤3.5kg
The RG-S2910-24GT4XS-E switch is a class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.
Product Appearance
The RG-S2910-24GT4XS-E full gigabit Ethernet switch provides 1 RJ45 Console port, 24 RJ45 10/100/1000Base-T
auto-sensing Ethernet ports and 4 SFP+ ports on the front panel.
Figure 1-1 Appearance of S2910-24GT4XS-E

Front Panel
Figure1-2 Front Panel of RG-S2910-24GT4XS-E
Note
1. System status LED
2. Console port
3. 10/100/1000 Base-T auto-sensing Ethernet port
4.10G SFP+ port
5.10G SFP+ port
6. 10/100/1000 Base-T copper port status LED
7. SFP+ fiber port status LED
Back Panel
Figure 1-3 Back Panel of RG-S2910-24GT4XS-E

Note
1. Grounding pole
2. Three-hole AC power receptacle
3. Power cord retention clips
Power Supply
The RG-S2910-24GT4XS-E switch adopts AC or HVDC power input.
AC input
Rated voltage range: 100V to 240V, 50/60 Hz
Maximum voltage range: 90V to 264V, 47 Hz to 63 Hz
Frequency: 50/60 Hz
Rated current: 1.5A
Power cord specification: 10A
HVDC input
Voltage range: 192V to 290V
Current range: 0.1A to 0.5A
Heat Dissipation
The RG-S2910-24GT4XS-E full gigabit switch is designed with fans. To ensure good dissipation, sufficient space (10 cm
distance from both sides and the back panel of the chassis) should be reserved for ventilation. It is recommended to clean
the switch at regular intervals (like once every 3 months). Especially, avoid dust from blocking the screen mesh on the
back of the cabinet; otherwise, the temperature of the device may go too high and affects the performance.
Figure 1-4 Flow Scheme of Heat Dissipation

When installing the device, sufficient ventilation space (1 U (44.45 mm) distance from the adjacent device) should be
reserved for the purpose of heat dissipation.
LEDs
LED
Panel Marker
Status
Indication
System status LED
Status
Blinking green
The system is being initialized.
Solid green
The switch is operational.
Solid red
Over-temperature, the system will reboot.
The switch is faulty.
10/100/1000 Base-T copper
port status LED
1-24
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
Solid yellow
The port is connected at 10/100 Mbps.
Blinking
Data are being transceived at the port.
SFP+ fiber port status LED
25F-28F
Off
The port is not connected.
Solid green
The port is connected.
Blinking
Data are being transceived at the port.
1.2 RG-S2910-48GT4XS-E
Technical Specifications
Model
RG-S2910-48GT4XS-E
CPU
Single-core CPU with the clock speed of 1.0G
BOOTROM
/
Flash Memory
256MB
SDRAM
DDRIII 512MB
Optical Module
See Appendix B.
The supported module type may change at any time. Consult us for the latest information.
SFP+ Port
Supports 10Gbase-R and 1000Base-X SFP+ modules.
Power Supply
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency: 50/60 Hz
Rated current: 1.5A
HVDC input
Voltage range: 192V to 290V

Current range: 0.5A to 0.8A
Earth Leakage
Current
≤3.5mA
EEE
Supported
PoE
Not supported
Power
Consumption
≤50W
Operating
Temperature
0ºC to 50ºC (32ºF to 122ºF )
Storage
Temperature
-40ºC to 70ºC (-40ºF to 158ºF )
Operating Humidity
10% to 90% RH
Storage Humidity
5% to 95% RH
Fan
Speed adjustment and fault alarm
Temperature
Warning
Supported
EMCStandards
GB9254-2008
Security Standards
GB4943-2011
Dimensions
(W x D x H)
443mm x 268mm x 44.5mm
Weight
≤4kg
The RG-S2910-48GT4XS-E switch is a class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.
Product Appearance
On the front panel, the RG-S2910-48GT4XS-E full gigabit Ethernet switch provides 1 RJ45 Console port, 48 RJ45
10/100/1000Base-T auto-sensing Ethernet ports and 4 SFP+ ports.
Figure 1-5 Appearance of S2910-48GT4XS-E

Front Panel
Figure1-6 Front Panel of RG-S2910-48GT4XS-E
Note
1. System status LED
2. Console port
3.10/100/1000 Base-T auto-sensing Ethernet port
4.10G SFP+ port
5.10G SFP+ port
6. 10/100/1000 Base-T copper port status LED
7. SFP+ port status LED
Back Panel
Figure 1-7 Back Panel of RG-S2910-48GT4XS-E

Note
1. Grounding pole
2. Three-hole AC power receptacle
3. Power cord retention clips
Power Supply
The RG-S2910-48GT4XS-E switch adopts AC or HVDC power input.
AC input
Rated voltage range: 100V to 240V, 50/60Hz
Maximum voltage range: 90V to 264V, 47 Hz to 63 Hz
Frequency: 50/60 Hz
Rated current: 1.5A
Power cord specification: 10A
HVDC input
Voltage range: 192V to 290V
Current range: 0.5A to 0.8A
Heat Dissipation
The RG-S2910-48GT4XS-E full gigabit switch is designed with fans. To ensure good dissipation, sufficient space (10 cm
distance from both sides and the back panel of the chassis) should be reserved for ventilation. It is recommended to clean
the switch at regular intervals (like once every 3 months). Especially, avoid dust from blocking the screen mesh on the
back of the cabinet; otherwise, the temperature of the device may go too high and affects the performance.
Figure 1-8 Flow Scheme of Heat Dissipation
LEDs

LED
Panel Marker
Status
Indication
System status LED
Status
Blinking green
The system is being initialized.
Solid green
The switch is operational..
Solid red
Over-temperature, the system will reboot.
The switch is faulty.
10/100/1000 Base-T copper
port status LED
1-48
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
Solid yellow
The port is connected at 10/100 Mbps
Blinking
Data are being transceived at the port.
SFP+ fiber port status LED
49F-52F
Off
The port is not connected.
Solid green
The port is connected.
Blinking
Data are being transceived at the port.
1.3 RG-S2910C-24GT2XS-P-E
Technical Specifications
Model
RG-S2910C-24GT2XS-P-E
CPU
Single-core CPU with the clock speed of 1.0G
BOOTROM
/
Flash Memory
512MB
SDRAM
DDRIII 512MB
Optical Module
See Appendix B.
The supported module type may change at any time. Consult us for the latest information.
Expansion Module
Supports M2900-01XT, M2910-01XS and M2910-02XS modules.
SFP Port
Supports 100Base-X and 1000Base-X SFP modules.
SFP+ Port
Supports 10Gbase-R and 1000Base-X SFP+ modules.
Power Supply
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency: 50/60 Hz
Rated current: 6A
HVDC input
Voltage range: 192V to 290V
Current range: 2.5A to 3.5A
Earth Leakage
Current
≤0.5mA
EEE
Supported

PoE
All the RJ45 ports are PoE-capable with the maximum power output of 30W.
The maximum output power of PoE/PoE+ is 370W.
The available number of PDs is determined by PSE output power and PD input power in
practice.
Power
Consumption
Less than 39W without extension cards or PoE load
Less than 470W with PoE full load
Operating
Temperature
0ºC to 50ºC (32ºF to 122ºF )
Storage
Temperature
-40ºC to 70ºC (-40ºF to 158ºF )
Operating Humidity
10% to 90% RH
Storage Humidity
5% to 95% RH
Fan
Speed adjustment and fault alarm
Temperature
Warning
Supported
EMC Standards
GB9254-2008
Security Standards
GB4943-2011
Dimensions
(W x D x H)
440mm x 260mm x 44mm
Weight
5.8kg (with package)
The RG-S2910C-24GT2XS-P-E switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
Product Appearance
On the front panel, the RG-S2910C-24GT2XS-P-E Ethernet switch provides 24 10/100/1000Base-T Ethernet ports, 2 GE
SFP fiber/copper combo ports, 2 10G SFP+ ports and 1 Console port. On the back panel, it provides AC power ports and
1 expansion module slot.
Figure 1-9 Appearance of RG-S2910C-24GT2XS-P-E

Front Panel
Figure 1-10 Front Panel of RG-S2910C-24GT2XS-P-E
Note:
1. System status LED
2. Expansion module status LED
3. PoE status LED
4. Copper port status LED
5. Fiber port status LED
6. PoE mode switch-over button
7. Console port
8. 10/100/1000Base-T auto-sensing Ethernet port
9. 100/1000Base-X SFP port
10. SFP+ port
Long press PoE Mode Switch-Over Button for above 2 seconds to switch the display mode between PoE mode and
port rate mode.
Back Panel
Figure 1-11 Back Panel of RG-S2910C-24GT2XS-P-E
Note:
1. Grounding pole
2. Expansion module slot
Power Supply
The RG-S2910C-24GT2XS-P-E switch adopts AC or HVDC power input.
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency range: 50/60 Hz

Rated current: 6A
Power cord specification: 10A
HVDC input
Voltage range: 192V to 290V
Current range: 2.5A to 3.5A
Heat Dissipation
The RG-S2910C-24GT2XS-P-E adopts turbine fans for heat dissipation, thereby ensuring normal function of the device in
the specified environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to
allow air circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents. Figure
1-12 shows the flow scheme of heat dissipation.
Figure 1-12 Flow Scheme of Heat Dissipation
LEDs
LED
Panel Identification
State
Meaning
System status LED
Status
Off
The switch is not receiving power.
Blinking green
The system is being initialized.
Continuous blinking indicates errors.

Solid green
The switch is operational.
Solid yellow
Temperature warning
Check the working environment of the switch
immediately.
Solid red
The switch is faulty.
Expansion module
status LED
Mod
Off
There is no expansion module or the expansion
module is not correctly installed.
Solid green
The expansion module is correctly installed.
PoE status LED
PoE
Solid green
Indicates the switching state.
Solid yellow
Indicates the PoE state.
1000Mbps RJ-45 port
status LED
1-24
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting traffic at 1000
Mbps.
Solid yellow
The port is connected at 10/100 Mbps.
Blinking yellow
The port is receiving or transmitting traffic at
10/100 Mbps.
RJ45 port PoE status
LED
1-24
Off
PoE is not enabled.
Solid green
PoE is enabled. The port is operational.
Solid yellow
The port has a PoE fault of overload.
1000Mbps SFP port
status LED
23F-24F
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting traffic at 1000
Mbps.

Solid yellow
The port is connected at 100 Mbps.
Blinking yellow
The port is connected at 100 Mbps.
SFP+ port status LED
25F-26F
Off
The port is not connected.
Solid green
The port is connected.
Blinking green
The port is receiving or transmitting traffic at 1000
Mbps.
1.4 RG-S2910C-24GT2XS-HP-E
Technical Specifications
Model
RG-S2910C-24GT2XS-HP-E
CPU
Single-core CPU with the clock speed of 1.0G
BOOTROM
/
Flash Memory
512MB
SDRAM
DDRIII 512MB
Optical Module
See Appendix B.
The supported module type may change at any time. Consult us for the latest information.
Expansion Module
Supports M2910-01XT and M2910-01XS modules.
SFP Port
Supports 100Base-X and 1000Base-X SFP modules.
SFP+ Port
Supports 10Gbase-R and 1000Base-X SFP+ modules.
RPS Type
Dual power supplies
Power Supply
RG- M5000E-AC500P
1) AC
Rated voltage range: 100V to 240V
Rated current range: 3.5A to 7A
Frequency range: 50/60 Hz
2) HVDC
Voltage range: 192 V to 290V
Rated current range: 2.5 A to 3.5 A
RG-PA1150P-F
1) AC
Rated voltage range: 100V to 240V

Frequency range: 50/60 Hz
Rated current: 10A
2) HVDC
Voltage range: 192V to 290V
Rated current: 10A
RG-M5000E-DC500P (DC)
Voltage range: -72V to -36V
Rated current: 16.5 A
Earth Leakage
Current
≤3.5mA
EEE
Supported
PoE
All the RJ45 ports are PoE-capable with the maximum power output of 30W.
The available number of PDs is determined by PSE output power and PD input power in
practice.
Power
Consumption
Less than 38W without extension cards or PoE load
Less than 850W with PoE full load
Operating
Temperature
0ºC to 50ºC (32ºF to 122ºF )
Storage
Temperature
-40ºC to 70ºC (-40ºF to 158ºF )
Operating Humidity
10% to 90% RH
Storage Humidity
5% to 95% RH
Fan
Speed adjustment and fault alarm
Temperature
Warning
Supported
EMCStandards
GB9254-2008
Security Standards
GB4943-2011
Dimensions
(W x D x H)
440mm x 320mm x 44mm (The depth is 410mm, when the RG-PA1150P-F power supply
module is in use.)
Weight
5.8kg (with package)
The RG-S2910C-24GT2XS-HP-E switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
Product Appearance
On the front panel, the RG-S2910C-24GT2XS-HP-E Ethernet switch provides 24 10/100/1000Base-T Ethernet ports, 2
GE SFP fiber/copper combo ports, 2 10G SFP+ ports and 1 Console port. On the back panel, it provides 2 power module
slots and 2 expansion module slots.
Figure 1-13 Appearance of RG-S2910C-24GT2XS-HP-E

Front Panel
Figure 1-14 Front Panel of RG-S2910C-24GT2XS-HP-E
Note
1. Expansion module 1 status LED
2. Expansion module 2 status LED
3. Power module 1 status LED
4. Power module 2 status LED
5. PoE status LED
6. Copper port status LED
7. Fiber port status LED
8. PoE mode switch-over button
9. Console port
10. USB port
11. 10/100/1000Base-T auto-sensing Ethernet port
12. 100/1000Base-X SFP port
13. SFP+ port
Long press PoE Mode Switch-Over Button for above 2 seconds to switch the display mode between PoE mode and
port rate mode.
Back Panel
Figure 1-15 Back Panel of RG-S2910C-24GT2XS-HP-E

Note:
1. Expansion module 1 slot
2. Expansion module 2 slot
3. Power module 1 slot
4. Power module 2 slot
5. Grounding pole
Power Supply
The RG-S2910C-24GT2XS-HP-E supports 2 power modules with AC or DC input. For the detailed power specification,
see the following tables.
Model
RG-M5000E-AC500P
RG-M5000E-AC500P (HVDC)
Platform
RG-S2910C-24GT2XS-HP-E
RG-S2910C-48GT2XS-HP-E
RG-S2910C-24GT2XS-HP-E
RG-S2910C-48GT2XS-HP-E
Rated Voltage Range
100V to 240V
50/60 Hz
240V
Maximum Voltage
Range
90 V to 264 V
50/60 Hz
192V to 290V
PoE Power
Single power supply: 370W
Dual power supplies: 740W
Hot Swapping
Supported
Redundant Power
Supplies
1+1
Over-Voltage
Protection
54 V: -60V to -57V
12 V: 13.4V to 16V
Over-Current
54V: 8A to 10A