Ruijie Networks RG-S2910C-XS-P Series Installation and operating manual

RG-S2910C-XS-P Series Switch
Hardware Installation and Reference Guide V1.00

Copyright statement
Ruijie Networks©2015
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
, , , , ,
, ,, ,
, , are registered trademarks of Ruijie Networks.
Counterfeit is strictly prohibited.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the switch.
Scope
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks website: http://www.ruijienetworks.com
Online customer services: http://webchat.ruijie.com.cn
Customer service center: http://www.ruijie.com.cn/service.aspx
Customer services hotline: [phone]
BBS: http://support.ruijie.com.cn
Customer services email: [email protected]
Related Documents
Documents Description
Configuration Guide Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Documentation Conventions
The symbols used in this document are described as below:
This symbol brings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the device or
cause data loss.

Product Overview
The RG-2910C-XS-P series is a multi-service 2-layer switch designed by Ruijie with high performance and security. It is
mostly applied at the access layer of large-sized networks to provide line-speed exchanging and complete QoS services,
and ensure low-delay transmission of key data by applying service-specific traffic classification rules. The
RG-2910C-XS-P series provides flexible medium interfaces and can meet the connection requirements of different media
in network constructions. RG-S2910C-XS-P is available in 3 models.
Table 1-1 Models of RG-2910C-XS-P
Model SFP+
10/100/1000Base-T
Auto-Sensing
Ethernet Port
1000Base-X
SFP Port
Console
Port
USB
Port
Expansion
Module
Slot
Redundant
Power
Supply
RG-S2910C-24G
T2XS-HP-E 2 24 (PoE+) 2 (Combo) 1 1 2 Dual
RG-S2910C-48G
T2XS-HP-E 2 48 (PoE+) 2 (Combo) 1 1 2 Dual
RG-S2910C-24GT2XS-HP-E
Technical Specifications
Model RG-S2910C-24GT2XS-HP-E
Optical Module
Ethernet 100M
FE-SFP-LX-MM1310
FE-SFP-LH15-SM1310
FE-SFP-LX20-SM1310-BIDI
FE-SFP-LX20-SM1550-BIDI
FE-SFP-LH40-SM1310-BIDI
FE-SFP-LH40-SM1550-BIDI
Ethernet 1000M
Mini-GBIC-SX
Mini-GBIC-LX

Mini-GBIC-LH40
Mini-GBIC-ZX50
Mini-GBIC-ZX80
Mini-GBIC-ZX100
GE-SFP-LX20-SM1310-BIDI
GE-SFP-LX20-SM1550-BIDI
GE-SFP-LH40-SM1310-BIDI
GE-SFP-LH40-SM1550-BIDI
Ethernet 10G
10G BASE-SR
10G BASE-LR
10G BASE-ER
1000Base-T
Mini-GBIC-GT
The supported module type may change at any time. Contact Ruijie
Networks for details.
Expansion Module
M2910-01XT
M2910-01XS
SFP Port
100Base-X
1000Base-X
SFP+ Port See Appendix C
RPS Type Dual power supplies
Power Supply
M5000E-AC500P
1) AC
Rated voltage range: 100 V to 240 V
Rated current range: 3.5 A to 7 A
Frequency range: 50/60 Hz

2) HVDC
Rated voltage range: 192 V to 290V
Rated current range: 2.5 A to 3.5 A
RG-PA1150P-F
1) AC
Rated voltage range: 100 V to 240 V
Frequency range: 50/60 Hz
Rated current: 10 A
HVDC
Rated voltage range: 192 V to 290 V
Rated current: 10 A
M5000E-DC500P (DC)
Rated voltage range: 36 V to 72 V
Rated current:16.5 A
PoE
Supported on all RJ45 ports
Up to 30 W power supported on each port, which is determined by the actual
power
Power Consumption 24-port PoE+: < 850 W
Temperature
Operating temperature: 0 to 50 ºC
Storage temperature: -40 to 70 ºC
Humidity
Operating humidity: 10% to 90%
Storage humidity: 5% to 90%
Fan Speed adjustment and fault alarm
Temperature Warning Supported
EMC Standards GB9254-2008
Safety Standards GB4943-2011
Dimensions (W x D x H) 440 mm x 320 mm x 44 mm

Weight 5.8 kg (with package)
The RG-S2910C-XS-P series switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
Product Appearance
The front panel of the RG-S2910C-24GT2XS-HP-E Ethernet switch provides twenty-four 10/100/1000Base-T Ethernet
ports, two GE SFP fiber/copper combo ports, two 10G SFP+ fiber ports and one Console port. The back panel provides
two power module slots and two expansion module slots. Figure 1-1 shows the appearance of
RG-S2910C-24GT2XS-HP-E.
Figure 1-1 Appearance of RG-S2910C-24GT2XS-HP-E
Front Panel
Figure 1-2 Front Panel of RG-S2910C-24GT2XS-HP-E

Note: System status LED
Expansion module 1 status LED
Expansion module 2 status LED
Power module 1 status LED
Power module 2 status LED
PoE status LED
Copper port status LED
Fiber port status LED
PoE mode switch-over button
Console port
USB port
10/100/1000Base-T auto-sensing Ethernet port
100/1000Base-X SFP port
SFP+ port
To ensure successful mode switch, press the PoE Mode Switch-Over button for 2 seconds or longer.
Back Panel
Figure 1-3 Back Panel of RG-S2910C-24GT2XS-HP-E
Note: Expansion module 1 slot
Expansion module 2 slot
Power module 1 slot
Power module 2 slot
Grounding pole
Power Supply
The RG-S2910C-24GT2XS-HP-E supports two power modules with AC or DC input. For the detailed power specification,
see the following tables.
Model RG-M5000E-AC500P RG-M5000E-AC500P (HVDC)
Platform
RG-S2910C-24GT2XS-HP-E
RG-S2910C-48GT2XS-HP-E
RG-S2910C-24GT2XS-HP-E
RG-S2910C-48GT2XS-HP-E

Rated Voltage Range
100 V to 240 V
50/60 Hz 240 V
Maximum Voltage
Range
90 V to 264 V
50/60 Hz 192 V to 290 V
PoE Power
Single power supply: 370W
Dual power supplies: 740W
Hot Swapping Supported
Redundant Power
Supplies 1+1
Over-Voltage
Protection
54 V: -60 V to -57 V
12 V: 13.4 V to 16 V
Over-Current
Protection
54V: 8 A to 10 A
12V: 12 A to 16 A
Over-Temperature
Protection Supported
Load-Balanced Power
Supply Supported
Power Supply Mix Supported with RG-M5000E-DC500P
Power Cord 10 A
Dimensions
(W x D x H)
224.5 mm x 90 mm x 40 mm (with connecting fingers and handles)
195.4 mm x 90 mm x 40 mm (without connecting fingers or handles)
Weight 1.6 kg
Model RG-M5000E-DC500P
Platform RG-S2910C-24GT2XS-HP-E

RG-S2910C-48GT2XS-HP-E
Rated Voltage Range -72 V to -32 V
PoE Power
Single power supply: 370 W
Dual power supplies: 740 W
Hot Swapping Supported
Redundant Power
Supplies 1+1
Over-Voltage
Protection
54 V: -66 V to -58 V
12 V: 13.2 V to 15.6 V
Over-Current
Protection
54V: 7.8 A to 10 A
12 V: 11 A to 14 A
Over-Temperature
Protection Supported
Load-Balanced Power
Supply Supported
Power Supply Mix Supported with RG-M5000E-AC500P
Power Cord PD650I (DC)
Dimensions
(W x D x H)
224.5 mm x 90 mm x 43.2 mm (with connecting fingers and handles)
195.4 mm x 90 mm x 43.2 mm (without connecting fingers or handles)
Weight 1.6 kg
Model RG-PA1150P-F RG-PA1150P-F (HVDC)
Platform
RG-S2910C-24GT2XS-HP-E
RG-S2910C-48GT2XS-HP-E
RG-S2910C-24GT2XS-HP-E
RG-S2910C-48GT2XS-HP-E
Rated Voltage Range 100 V to 240V 240 V

50/60 Hz
Maximum Voltage
Range
90 V to 264 V
50/60 Hz
192 V to 290 V
PoE Power
Single power supply: 740 W
Dual power supplies: 1480 W
Hot Swapping Supported
Redundant Power
Supplies 1+1
Over-Voltage
Protection
54V: -60 V to -57 V
12V: 14 V to 16 V
Over-Current
Protection
54V: 16.5 A to 20 A
12V: 32 A to 40 A
Over-Temperature
Protection Supported
Load-Balanced Power
Supply Supported
Power Supply Mix Not supported
Power Chord 10 A
Dimensions
(W x D x H)
301 mm x 90 mm x 40 mm (with connecting fingers and handles)
281 mm x 90 mm x 40 mm (without connecting fingers or handles)
Weight 1.6 kg
Dual-power input: The switch can be powered by one power module, or two power modules. When both two modules are
available, the switch is powered in load-balanced state.
When the switch is powered by the dual-power modules, if the system working power is greater than the
capacity of single power module, power redundancy cannot work.

Heat Dissipation
The RG-S2910C-24GT2XS-HP-E adopts turbine fans for heat dissipation, thereby ensuring normal function of the device
in the specified environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to
allow air circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents. Figure
1-4 shows the flow scheme of heat dissipation.
Figure 1-4 Flow Scheme of Heat Dissipation
LEDs
LED Panel Identification State Meaning
Off The switch is not receiving power.
Blinking green
Initialization in progress.
Continuous blinking indicates errors.
System status LED Status
Solid green The switch is operational.

Solid yellow
Temperature warning.
Check the working environment of the switch
immediately.
Solid red
The switch is faulty.
For details, see the section “Troubleshooting
Common Faults”.
Off There is no expansion module or the expansion
module is not correctly installed.
Expansion module
status LED M1/M2
Solid green The expansion module is correctly installed.
Off The power module is not in place.
Solid red The power module is in place but the AC power
cord or switch is abnormal.
Power module status
LED PWR1/PWR2
Solid green The power supply is operational.
Solid green Indicates the switching state.
PoE status LED PoE
Solid yellow Indicates the PoE state.
Off The port is not connected.
Solid green The port is connected at 1000 Mbps.
Blinking green The port is receiving or transmitting traffic at 1000
Mbps.
Solid yellow The port is connected at 10/100 Mbps.
1000Mbps RJ-45 port
status LED 1-24
Blinking yellow The port is receiving or transmitting traffic at
10/100 Mbps.
Off PoE is not enabled.
Solid green PoE is enabled. The port is operational.
RJ45 port PoE status
LED 1-24
Solid yellow The port has a PoE fault of overload.

Off The port is not connected.
Solid green The port is connected at 1000 Mbps.
Blinking green The port is receiving or transmitting traffic at 1000
Mbps.
Solid yellow The port is connected at 100 Mbps.
1000Mbps SFP port
status LED 23F-24F
Blinking yellow The port is receiving or transmitting traffic at 100
Mbps.
Off The port is not connected.
Solid green The port is connected.
SFP+ port status LED 25F-26F
Blinking green The port is receiving or transmitting traffic at 1000
Mbps.
RG-S2910C-48GT2XS-HP-E
Technical Specifications
Model RG-S2910C-48GT2XS-HP-E
Optical Module
Ethernet 100M
FE-SFP-LX-MM1310
FE-SFP-LH15-SM1310
FE-SFP-LX20-SM1310-BIDI
FE-SFP-LX20-SM1550-BIDI
FE-SFP-LH40-SM1310-BIDI
FE-SFP-LH40-SM1550-BIDI
Ethernet 1000M
Mini-GBIC-SX
Mini-GBIC-LX
Mini-GBIC-LH40
Mini-GBIC-ZX50

Mini-GBIC-ZX80
Mini-GBIC-ZX100
GE-SFP-LX20-SM1310-BIDI
GE-SFP-LX20-SM1550-BIDI
GE-SFP-LH40-SM1310-BIDI
GE-SFP-LH40-SM1550-BIDI
Ethernet 10G
10G BASE-SR
10G BASE-LR
10G BASE-ER
1000Base-T
Mini-GBIC-GT
The supported module type may change at any time. Contact Ruijie
Networks for details.
Expansion Module
M2910-01XT
M2910-01XS
SFP Port
100Base-X
1000Base-X
SFP+ Port See Appendix C
RPS Type Dual power supplies
Power Supply
M5000E-AC500P
1) AC
Rated voltage range: 100 V to 240 V
Rated current range: 3.5 A to 7 A
Frequency range: 50/60 Hz
2) HVDC
Rated voltage range: 192 V to 290V

Rated current range: 2.5 A to 3.5 A
RG-RG-PA1150P-F
1) AC
Rated voltage range: 100 V to 240 V
Frequency range: 50/60 Hz
Rated current: 10 A
2) HVDC
Rated voltage range: 192 V to 290V
Rated current: 10A
M5000E-DC500P (DC)
Rated voltage range: -72 V to -36 V
Rated current:16.5 A
PoE
Supported on all RJ45 ports
Up to 30 W power supported on each port, which is determined by the actual
power.
Power Consumption 48-port PoE+: < 1700 W
Temperature
Operating temperature: 0 to 50 ºC
Storage temperature: -40 to 70 ºC
Humidity
Operating humidity: 10% to 90%
Storage humidity: 5% to 90%
Fan Speed adjustment and fault alarm
Temperature Warning Supported
EMC Standards GB9254-2008
Safety Standards GB4943-2011
Dimensions (W x D x H) 440 mm x 360 mm x 44 mm
Weight 6.8 kg (with package)

The RG-S2910C-XS-P series switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
Product Appearance
The front panel of the RG-S2910C-48GT2XS-HP-E Ethernet switch provides forty-eight 10/100/1000Base-T Ethernet
ports, two GE SFP fiber/copper combo ports, two 10G SFP+ fiber ports and one Console port. The back panel provides
two power module slots and two expansion module slots. Figure 1-5 shows the appearance of the
RG-S2910C-48GT2XS-HP-E .
Figure 1-5 Appearance of RG-S2910C-48GT2XS-HP-E
Front Panel
Figure 1-6 Front Panel of RG-S2910C-48GT2XS-HP-E

Note: System status LED
2. Expansion module 1 status LED
3. Expansion module 2 status LED
4. Power module 1 status LED
5. Power module 2 status LED
6. PoE status LED
7. Copper port status LED
8. Fiber port status LED
9. PoE mode switch-over button
10. Console port
11. USB port
12. 10/100/1000Base-T auto-sensing Ethernet port
13. 100/1000Base-X SFP port
14. SFP+ port
Back Panel
Figure 1-7 Back Panel of RG-S2910C-48GT2XS-HP-E
Note: Expansion module 1 slot
Expansion module 2 slot
Power module 1 slot
Power module 2 slot
Grounding pole
Power Supply
The RG-S2910C-48GT2XS-HP-E supports two power modules with AC or DC input. For the detailed power specification,
see the section of Power Supply for RG-S2910C-24GT2XS-HP-E.
Dual-power input: The switch can be powered by one power module, or by two power modules. When both two modules
are available, the switch is powered in the load-balanced mode.
When the switch is powered by the dual-power modules, if the system working power is greater than the
capacity of single power module, the power redundancy cannot work.
Heat Dissipation
The RG-S2910C-48GT2XS-HP-E adopts turbine fans for heat dissipation, thereby ensuring normal function of the device
in the specified environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to
allow air circulation. It is recommended to clean the device once every 3 months to prevent dust from blocking vents.
Figure 1-8 shows the flow scheme of heat dissipation.

Figure 1-8 Flow Scheme of Heat Dissipation
LEDs
LED Panel Identification State Meaning
Off The switch is not receiving power.
Blinking green Initialization in progress.
Continuous blinking indicates errors.
Solid green The switch is operational.
System status LED Status
Solid yellow
Temperature warning.
Check the working environment of the switch
immediately.

Solid red
The switch is faulty.
For details, see the section “Troubleshooting
Common Faults”.
Off There is no expansion module or the expansion
module is not correctly installed.
Expansion module
status LED M1/M2
Solid green The expansion module is correctly installed.
Off The power module is not in place.
Solid red The power module is in place but the AC power
chord or switch is abnormal.
Power module status
LED PWR1/PWR2
Solid green The power supply is normal.
Solid green Indicates the switching state.
PoE status LED PoE
Solid yellow Indicates the PoE state.
Off The port is not connected.
Solid green The port is connected at 1000 Mbps.
Blinking green The port is receiving or transmitting traffic at 1000
Mbps.
Solid yellow The port is connected at 10/100 Mbps.
1000Mbps RJ-45 port
status LED
1-24
Blinking yellow The port is receiving or transmitting traffic at
10/100 Mbps.
Off PoE is not enabled.
Solid green PoE is enabled. The port is operational.
RJ45 port PoE status
LED 1-48
Solid yellow The port has a PoE fault of overload.
Off The port is not connected.1000Mbps SFP port
status LED
47F-48F
Solid green The port is connected at 1000 Mbps.