Russell Hobbs RHMP700 Installation instructions manual

MULTI PROCESSOR
MODEL RHMP700
Instructions & Warranty
RHMP700_IB&RB_180211

Russell Hobbs has been synonymous with life in the kitchen for
over 50 years. Known, owned and proudly on display in
millions of homes across the country. Allow Russell Hobbs to
forge a reputation for timeless, stylish appliances in your home.
Russell Hobbs through and through
Complete range of Russell Hobbs products are available at
www.russellhobbs.com.au | www.russellhobbs.co.nz
Salton (Aust) Pty. Ltd. | P.O. Box 683 Braeside Victoria 3195 Australia | TollFree 1800 427 824
Salton NZ Ltd. | P.O. Box 300 201 Albany Auckland 0752 New Zealand | FreeCall 0508 629 777

Congratulations on the purchase of your Russell Hobbs appliance. Each unit is manufactured to
ensure safety and reliability. Before using the appliance for the first time, please read the instruction
booklet carefully and keep it for future reference. Pass it on if you pass on the appliance.
When using electrical appliances, basic safety precautions should always be followed.
Limited 2 year warranty
There is no need to post us anything, just retain your receipt/proof of purchase with this booklet.
Nothing in this warranty or the instructions relating to the product excludes, restricts or otherwise
affects your statutory rights under the Trade Practices Act 1974 and other relevant legislation.
In addition to your statutory rights, Salton (Aust) Pty Ltd and Salton NZ Ltd (hereafter referred to as
“Salton”) provide a LIMITED 2 YEAR WARRANTY for this product. Salton warrants this product
free from defects in material and workmanship for two (2) years from the date of purchase. Within
this warranty period Salton will repair or replace defective parts at no charge. Defective products
may be returned to Salton or the place of purchase. If distance prevents you from taking the
product to the place of purchase, please call the Salton Customer Service department TollFree
within Australia 1800 427 842, or FreeCall within New Zealand 0508 629 777.
The warranty does not cover improper installation, misuse, abuse or neglect of the product. This
warranty also does not cover any product taken apart, altered or serviced by an unauthorised repairer.
Register your product online
Registration of your warranty is not compulsory, but entitles you to receive these benefits:
3URGXFWLQIRUPDWLRQ 3URGXFWKLQWVDQGWLSV
5HFLSHVDQGQHZV ,QIRUPDWLRQRQVSHFLDOSULFHRffers and promotions
If you live in Australia please visit
www.salton.com.au/warranty
If you live in New Zealand please visit
www.salton.co.nz/warranty
AUSTRALIAN CUSTOMER SERVICE
Salton (Aust) Pty. Ltd.
P.O. Box 683
Braeside Victoria 3195
Australia
TollFree: 1800 427 842
Hours: 9am-5pm (EST) Mon-Fri
Any questions?
Please contact Customer Service for advice.
NEW ZEALAND CUSTOMER SERVICE
Salton NZ Ltd.
P.O. Box 300 201
Albany Auckland 0752
New Zealand
FreeCall: 0508 629 777
Hours: 9am-5pm Mon-Fri

4
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a tamper-resistant screw to prevent removal of
the outer cover. To reduce the risk of fire or electric shock, do not attempt to remove the
outer cover. There are no user-serviceable parts inside. Repair should be done only by
qualified service personnel.
ELECTRICAL CORD
The cord of this appliance was selected to reduce the possibility of tangling in or tripping
over a longer cord. If more length is needed, use an extension cord rated no less than
10 amperes. When using an extension cord, do not let it drape over the working area or
dangle where someone could accidentally trip over it. Handle cord carefully for longer life;
avoid jerking or straining it at outlet and appliance connections. The maximum rating is
based on the chopping blade; other attachments may draw significantly less power.
INTRODUCTION
Thank you for choosing the Russell Hobbs Multi Processor.
 700 Watt motor delivers the power to perform all your processing needs.
 At the touch of a button you can blend, slice, chop, shred, grate, puree and much more.
 Handles large food items without having to section it.
 Brushed stainless steel exterior makes cleaning a breeze and removable parts are
dishwasher safe.
GETTING FAMILIAR WITH YOUR UNIT
10 cup
food processor 3 cup chopping bowl 6 cup blender
Wide mouth
feed chute Suction feet Powerful 700 Watt motor
7
6

5
1. Food pusher
2. Wide-mouth feed chute
3. 10 cup processing workbowl cover
4. Coarse slice/shred disc
5. Disc stem
6. 10 cup processing workbowl
6A. Centre Post (White)
7. Base
8. Storage lid
9. Dough blade
10.Large stainless steel chopping blade
(White)
11. Fine slice/shred disc
12.Cord wrap (under base)
13.Non-slip suction feet
14.Controls
15.3 cup workbowl cover
16.Small stainless steel chopping blade
(Black)
17.3 cup processing workbowl
17A. Centre Post (Black)
1
2
3
4
5
6
6A
7
14
9
10
13 12 11
8
15
16
17
17A
NOTE: Product may vary slightly
from what is illustrated.

6
18.Lid cap with measurement units
19.Lid
20.6 cup (1250 ml) glass blender jug
21.Handle
22.Gasket
23.Blade assembly
24.Jug base
18
20
19
22
21
23
24

7
BEFORE FIRST USE
Important: Handle chopping blades and slice/shred disc carefully.
Remove all packaging material and any stickers from the product. Wash all removable
parts as instructed in “care and cleaning” section of this manual. Select a level, dry
countertop where the appliance is to be used, allowing air space on all sides to provide
proper ventilation for the motor (50mm gap min).
ASSEMBLING THE FOOD PROCESSOR / MINI CHOPPER
HOW TO INSERT AND REMOVE THE CENTRE POST
The centre post of the bowl is removable (3 Cup - Black, 10 Cup - White):
1. Turn the bowl upside down.
2. Grasp the outer tabs and turn the centre post clockwise until the
locking tabs are free. Lift the post out (A).
3. To return to its original position, place centre post into opening
in bottom of workbowl and turn counterclockwise until tabs snap
into place.
NOTE: The 10 cup bowl and 3 cup bowl centre posts are not
interchangeable.
HOW TO LOCK THE WORKBOWL IN POSITION:
1. Place the workbowl on the base with handle turned to the right
of the locking mechanism (B) over the unlock symbol .
2. Hold handle and rotate workbowl clockwise toward the lock
symbol XQWLOLWFOLFNV¿UPO\LQWRSODFH&%HVXUHWRORFNWKH
workbowl in place before attaching the blades and cover.
HOW TO LOCK THE COVER
1. Place cover over workbowl with the small latch to the right of the
workbowl’s handle (D).
2. Hold feed chute of workbowl cover and rotate cover clockwise
until cover locks into place.
Important: For your protection this appliance has an interlock
system. The processor will not operate unless the workbowl, cover
and wide-mouth feed chute are properly locked in place.
3. Place the wide-mouth feed chute on top of the cover with the
small tab to the right of the workbowl’s handle. Turn clockwise
until it clicks into position in the handle.
4. Insert the food pusher into the central tube of the wide mouth
feed chute. Turn clockwise to lock in place. The pusher is used
to guide foods through the feed chute and can be removed when
adding liquid or additional foods while the processor is running.
To remove, turn counterclockwise.
A
B
C
D

8
CONTROLS
The controls are located on the front of the base (E). Press PULSE, HIGH or LOW to
select a function (see directions below).
OFF/PULSE
Processor should be stored in OFF position and unplugged when
not in use.
Use PULSE for short processing tasks. This lets you control the
size and uniformity of foods being chopped.
The OFF/PULSE button must be pressed and held for the
appliance to operate in PULSE mode. When released, the
appliance will stop.
The motor of the processor will run as long as the OFF/PULSE button is held down.
Press the button and then release to allow the blades to stop running and the food to fall
to the bottom of the workbowl.
Pulsing gives better control when chopping, mincing, mixing and blending foods. You can
FRQWUROWKHVL]HRIWKHIRRGVIURPFRDUVHWR¿QH
HIGH AND LOW
When either speed is selected, the processor will run continuously until the OFF/PULSE
button is pressed.
HOW TO CHOP IN THE WORKBOWL
7KHFKRSSLQJEODGHLVXVHGWRFRDUVHO\RU¿QHO\FKRSPLQFHPL[DQGSXUHHIRRGVWRD
smooth consistency. 1. Lock workbowl into position (see Illustrations B and C).
2. Hold chopping blade by centre shaft and insert onto centre post
(F).
Caution: The blade attachments are very sharp. Use caution
when handling and storing.
3. Place food in workbowl.
4. Place cover on workbowl and lock into place by rotating
clockwise (see Illustration D).
5. Place the wide-mouth feed chute and food pusher in place, turn to lock.
,PSRUWDQW1HYHUXVH\RXU¿QJHUVWRGLUHFWIRRGWKURXJKWKHFKXWH
6. Select your desired speed (PULSE, LOW or HIGH).
NOTE: Process foods for no more than a few seconds at a time. Pulsing produces
excellent results and offers greater control.
7. Food can be added while processor is running; remove food pusher and insert food
through the feed chute. Replace food pusher in chute.
Important: Be sure chopping blade has completely stopped spinning before
removing cover from processor.
8. Press the OFF/PULSE button and allow blades to stop revolving before removing
cover. Twist cover toward to remove.
9. Unlock workbowl by turning it counterclockwise and lift off base.
E
F

9
NOTE: Remove bowl from appliance before removing blade to prevent food from leaking
through the centre opening of the bowl.
10.Carefully remove chopping blade.
11. Unplug appliance when not in use.
HELPFUL TIPS FOR CHOPPING AND BLENDING
The processor works very quickly.
Watch carefully to avoid over-processing foods.
The PULSE button offers the best control and results.
For best results, process foods that are about the same size.
Do not overload the bowl.
Never walk away from the processor while it is on.
Use hot but never boiling liquids.
Do not process more than 3 cups liquid in the workbowl at one time.
To process meat, use no more than 2 cups of 20mm cubes in the workbowl. Process
using PULSE in 5 second intervals.
The workbowl has a capacity of 10 cups.
 ,QVHUWDIXQQHOLQWRWKHIHHGFKXWHZKHQDGGLQJLQJUHGLHQWVVXFKDVRLOÀRXUDQGVXJDU
USING THE DOUGH BLADE (same assembly method as the chopping blade)
7KLVEODGHPDNHVSUHSDULQJGRXJKHI¿FLHQWDQGWLPHVDYLQJ
1. This blade does not extend to the outside rim of the workbowl, so it cannot incorporate
ÀRXUZKHQYHU\VPDOODPRXQWVRIÀRXUDUHEHLQJSURFHVVHG
2. Push dough blade down as far as it will go into workbowl.
3. Insert all the dry ingredients into the workbowl.
4. Place cover on workbowl. Add wide-mouth feed chute and food pusher. Process to
blend.
5. Add liquids through the small feed chute with machine running.
HELPFUL TIPS WHEN USING THE DOUGH BLADE
 )RUEHVWUHVXOWVGRQRWSUHSDUHUHFLSHVXVLQJPRUHWKDQòFXSVÀRXU
 %HJLQZLWKFXSOHVVWKDQWKHPD[LPXPDPRXQWRIÀRXUDQGDGGDGGLWLRQDOÀRXURQFH
mixture is well blended.
Pour liquid through food chute gradually.
Knead dough no longer than 1 minute.
Do not leave processor unattended during operation.

10
HOW TO SLICE OR SHRED
1. Lock workbowl into position (see Illustrations B and C).
2. Place disc stem onto centre post in workbowl.
3. Carefully place slice/shred disc on stem with appropriate side up (depending on work to
be done).
CAUTION: The blade attachments are very sharp. Use caution when handling and storing.
4. Place cover on workbowl and lock into place by rotating cover clockwise (see
Illustration D).
5. For large size food insert before attaching the chute, then attach chute and use the
pusher Fig G(a). For smaller size food attach cover and feed through using pusher.
NOTE that the pusher clips onto the moving chute tube. Fig G.
6. 6HOHFW38/6(/2:RU+,*+SUHVV¿UPO\RQIRRGSXVKHUWRJXLGHIRRGWKURXJK
processor, but do not force it.
NOTE: Heavy pressure on the pusher does not speed the work; use the pusher only as a
guide. Let the processor do the work.
7. :KHQ¿QLVKHGSUHVV2))38/6(DQGZDLWIRUGLVFWRVWRSURWDWLQJEHIRUHUHPRYLQJ
cover. Twist cover toward to remove.
8. Carefully remove slice/shred disc. Unlock workbowl by turning it counterclockwise and
lifting it off the base.
9. Unplug appliance when not in use.
HELPFUL TIPS WHEN SLICING AND SHREDDING
Before slicing round fruits and vegetables in the processor, cut a thin slice from the
bottom so food will be more stable. Place food cut side down in feed chute.
Always remove seeds and pits before processing.
Remove the core from hard vegetables, such as cabbage.
When slicing thinner vegetables, cut them just short of the length of the feed chute and
stand them vertically in feed chute so they are solidly packed and cannot turn or tilt.
Shred hard cheeses at room temperature.
Soft and semi-hard cheeses should be well chilled before shredding.
After food has been processed, remove the cover and invert on countertop. Remove
the slice/shred disc before removing the workbowl from the processor. Place the disc
on top of the inverted workbowl cover.
GG(a)
OR