SAESHIN Brillian medipro User manual

WARNING
USER GUIDELINES
Design and specification of the product can be subject to be
changed without notice for improving the quality.
●Check the power switch before connecting the power cord in order to decrease the danger
by sudden operation of product.
●Do not use the damaged bur. It causes product’s malfunction and accident.
●Replace the bur after stopped the handpiece.
●Be careful not to drop the product as it may be damaged or broken. In case that is dropped, c heck if the bur is
bent or that any overheat is generated while carefully operating it.
●Follow the user manual by manufacturer of bur to use bur.
●Keep the recommended speed limit by manufacturer of bur to use bur.
If exceed the speed limit, it might cause
an accident.
●
Contact to the manufacturer in case of damage of power cord and cable. It causes fire or electric shock.
●When unplugging the power cord, be sure to grasp the plug and do not hold the plug with wet hands. Do not
use while the power plug is loose. It causes electric shock or fire.
●Do not bend or press the power cord excessively. It causes electric shock or fire.
●Do not install near a hot air balloon or place candles or cigarettes around. It causes fire.
●Carefully observe whether the elderly, the disabled or children are near the place where
this product is installed
and do not leave children alone.
●
If use the extension cord, do not use many electric devices at one time. It causes fire or electric shock.
●Do not install it in a humid place such as a bathroom or in a place exposed to snow or rain. It causes electric
shock or fire.
PRODUCT SPECIFICATION
Control Box CMDV4 Handpiece HMD03
Input voltage Power Fuse Size (WxLxH) Weight Size Rotation
speed Torque
Weight
110V 50/60Hz 120W 5A/2A
9 3/4 x 10 1/2 x 6
3/4 in
(25х26,5х17 cm)
10.8 lb
(4.9 kg)
10 ½ x 1
in
(265x27
mm)
0-40 000
RPM 5 Ncm 13 oz (368 g)
MANUAL
INTRODUCTION
Make sure to read this user manual before using.
This user manual is to assure proper installation and use.
Pay attention to read this manual in order to make the best use of this product
and to assure the prolonged lifespan before using.
Operating condition
Transport and
Storage condition
10~30
10~80
700~1,060
-20~60
10~90
500~1,060
Temperature (℃)
Relative humidity (%)
Atmospheric pressure (hPa)
Temperature (℃)
Relative humidity (%)
Atmospheric pressure (hPa)
E1 means handpiece bad connection or motor fault.
Reconnect handpiece. If not, contact to the seller.
■ ERROR CODE
ERROR CODE SOLUTION
E1
WARRANTY
The warranty for this product is guaranteed for the product as follows in accordance
with the standards notified by the Fair Trade Commission of the Consumer Damage
Compensation Regulations, and is carried out at the headquarters customer center
and designated A/S center upon request for service.
The free warranty period of this product is one year from the date of purchase and is
guaranteed in accordance with the consumer damage compensation regulations.
Failures within the warranty period are not subject to any technical fees and parts fees
in the following cases.
· If there is a problem with the product itself when first installed
· In case of malfunction due to manufacturing abnormality in normal operating condition
Exception of warranty
· User’s misuse or improper use and treatment
· Use the product with incorrect input voltage (AC voltage)
· Drop the device during setting, moving and using.
· Use the not recommended consumables or accessories
· Malfunction after repairing the product at the not recommended repair shop
· Faulty by Act of God
· Attempt to disassemble or modify product
52, Secheon-ro 1-gil, Dasa-eup,
Dalseong-gun, Daegu, Korea
Tel. [phone] / Fax. [phone]
Manufactured by. Distirbuted by.
MASHA’S NAILS SHOP
Tel. [phone] (WhatsApp )
www.4nails.us |[e-mail]
· If an abnormality occurs during use, check the following.
■ Before requesting A/S
Is the power plug firmly inserted?
Have you checked the power of control box?
Has there been a power outage?
Do you use the electric capacity correctly?
Have you checked the fuse?
Is the handpiece cord properly connected?
Are the burs not fixed or come off?
Are you using a bur that meets the specifications?
Have you not cleaned it with water?
Have you drop it while moving?
The problem is not working normally.
Symptom Check list
Date of sale Serial number
4

PRODUCT COMPONENTS
PART NAME OF CONTROL BOX
①②
③
④
⑤
⑥
HANDLE
HANDPIECE HOLDER FOOT PEDAL CONNECTOR
RPM DISPLAY
SPEED CONTROL DIAL FUSE BOX
POWER CONNECTION
HPOWER SWITC
VACUUM LEVEL DIAL
VACUUM LEVEL DISPLAY
ON/OFF BUTTON
⑦ Turn off the power when finished work.
■ How to use when select the hand
- Motor rotates when pressing motor
on/off button.
- Motor stops when pressing motor
on/off button one more.
- Press the foot pedal.
Motor rotates during pressing the pedal.
- Motor stops when foot pedal is released.
■ How to use when select the foot
OPERATION PROCESS
① Turn power on at the back of the control box.
② Turn on at the front of the control box.
(Figures show on the rotation speed display and vacuum level display when turning power on.)
③ Select rotation direction.
When FWD lamp turns on, it rotates in forward direction and when REV lamp turns on, it rotates in
reverse direction.
④ Select vacuum mode.
·
In the model of “AUTO”, rotation speed and vacuum level can be controlled simultaneously.
(Speed
changes simultaneously by turning rotation speed dial.)
· In the model of “MANUAL”, rotation speed and vacuum level can be controlled separately.
(Adjustment by each dial)
⑤ Turn on vacuum function by turning on the vacuum ON/OFF button.
(Turn off this function if you don’t use.)
⑥ Select hand/foot mode.
- Change rotation direction when motor stops compeletely.
- Replace the bur when motor stops completely.
- Never operate the motor wihtout dust bag.
BUTTONS ON THE OPERATION PANEL
■ Power button
: When you push the power button, the power turns on and figures
show on the rotation speed display and vacuum level display.
■ Rotation direction select button
: it is used to choose forward/reverse direction.
■ Hand/Foot select button
:
When selecting “Hand”, adjust rotation speed or vacuum level by rotating the dial.
: When selecting “Foot”, you can operate by pressing foot pedal.
■ Auto/Manual select button
: When selecting “manual”, rotation speed and vacuum level can be controlled separately.
: When selecting “auto”, rotation speed and vacuum level can be controlled simultaneously.
■ Motor ON/OFF button
: You can operate production
or stop.
■ Vacuum level ON/OFF button
: You can operate vacuum function
or stop.
POWER
HANDPIECE
3. Foot pedal connection: Connect foot pedal.
4. Power cord connection
: Connect power cord to the back part of the
control box.
C ONNECTION OF EACH P AR T
FOOT CONTROLLER
1. Control box
2. Handpiece
3. ON/OFF foot controller
5. Power Cord
6. Dust Bag
7. Handpiece Holder
■ Control box connection
1. Dust bag connection
: Assemble dust bag into the handpiece connector.
2. Handpiece connection
: Connect pins of the hand-piece connector to the control box
correctly. (Pins should be to the upper direction.
MAINTENANCE OF THE PRODUCT
① Take out the bur and disassemble handle case and motor cap.
② Separate motor by pushing handle case to the front direction.
③ Clean each part with dry cloth.
■ HOW TO CHANGE THE DUST BAG
2 3