Safavieh Furniture Halvor HBD6502A User manual

Weight Capacity - 220 LBS
Warning : Do not stand on Headboard
Warning : Do not over torque bolts.
WARNING
HBD6502A-T
39.37" x 1.18" x 43.7"
NOTICE
PREPARATION
CARE AND MAINTENANCE
* Please make sure that you have all parts indicated and they are in good condion before you
begin assembly of this item. Refer to part list and hardware list below for guidance.
* This item should be assembled on a so surface to prevent scratching the finish during assembly.
* This item may require periodic ghtening.
* If you are having difficulty, our friendly Customer Care team is always here to help.
Please email [e-mail]
* Before beginning assembly of product, make sure all parts are present. Compare parts with
part contents list and hardware contents list.
* If any part is missing or damaged, do not aempt to assemble the product.
* Esmated Assembly Time: 10 minutes.
* Tools Required for Assembly (included): Allen Key
Raan Care : Do not expose your furniture to any liquids. All liquids should be
wiped up immediately with a so, slightly damp cloth In the direcon of the raan.
Do not exposeyour furniture to strong or direct sunlight, heat outlets, open windows
and dampness. Excessive exposure ton sunlight can cause fading of your furniture finish.
Extreme temperatures and humidity changes can cause cracking and spling.
Wood Care : Always use felt pads under all arcles to prevent discoloraon or soening
or the lacquer. Plasc and rubber bases on items can discolor wood. Wipe up spills
immediately and avoid common hazards such as hot dishes, harsh solvent and abrasives.
Cleaning Should be done with a so lint free coon cloth dampened with water or furniture
polish. On highly used surfaces we recommended applying a quality paste wax which should
be used on a regular basis to provide addional protecon from scratches and spill.
how oen you apply the wax depend on how much wear the furniture receives.

150 mm
20 mm
Part List and Hardware List
A
BLegs
Top
PIECE DESCRIPTION PICTURE QTY
CMetal Connector
1
2
2
C
HW1 Bolt 8
Allen Key 1
Screw 1
Screw 1
Anchor Plug
PIECE DESCRIPTION PICTURE QTY
HW2 Ring 8Strap
HW3
HW4
40 mm
20 mm
HW5
HW6
HW7
1
1

PREPARATION
* Before beginning assembly of product, make sure all parts are present. Compare parts with part contents list and hardware contents list.
* If any part is missing or damaged, do not aempt to assemble the product.
* Esmated Assembly Time: 10 minutes.
* Tools Required for Assembly (included): Allen Key
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email [e-mail]
STEP 1 : CONNECT THE LEGS AND THE TOP OF THE
HEADBOARD USING THE METAL CONNECTOR ACCORDING TO
THE ARROW INSTRUCTIONS IN THE PICTURE
STEP 4 : REMOVE TOP DRAWER FROM ASSEMBLED UNIT. THEN
STRAP (HW7) WITH SHORT SCREW (HW5) TO THE UNDERSIDE
OF TOP PANEL ( A ) USING PHILLIPS HEAD SCREW DRIVER, NOT
INCLUDED. TIGHTEN COMPLETELY.
STEP 2 : PUT RING & BOLT INTO THE METAL CONNECTOR THEN
TIGHTEN IT USING ALLEN KEY.
STEP 5 : DETERMINE WHERE THE STORAGE UNIT IS TO BE
PLACED, THEN MARK THE POSITION ON THE WALL SO THE
WALL ANCHOR ( HW6 ) WILL ALIGN WITH THE STRAP ( HW7 )
ON THE BACK OF THE STORAGE UNIT. THE DRILL HOLE IN THE
WALL. PRESS WALL ANCHOR ( HW6 ) INTO THE HOLE.
STEP 3 : YOUR HEADBOARD IS READY.
STEP 6 : CONNECT STRAP (HW7) WITH LONG SCREW (HW4) TO
WALL ANCHOR (HW6) USING PHILLIPS HEAD SCREW DRIVER,
NOT INCLUDED. THIGHTEN COMPLETELY. THEN REPLACE TOP
DRAWER INTO ASSEMBLED UNIT.
C
HW1HW1
HW2
HW3
B
HW1HW1
HW6 HW4
A
B
A
B
HW7
HW5
A
HW6
HW6
HW7