Safavieh Furniture Logan ETG4200 User manual

Item ID# ETG4200
Product Dimensions:16-1/2"WX16-1/2"DX55"H
CARE AND MAINTENANCE
Always use felt pads under all articles to prevent discoloration or softening of the
lacquer. Plastic and rubber bases on items can discolor wood. Wipe up spills
immediately and avoid common hazards such as hot dishes,harsh solvents and
abrasives. Cleaning should be done with a soft lint free cotton cloth dampened with
water or furniture polish. On highly used surfaces we recommend applying a quality
paste wax which should be used on a regular basis to provide additional protection
from sratches and spills. How often you apply the wax depends on how much wear the
furniture receives.
NOTICE
* Please make sure that you have all parts indicated before you begin assembly of this
item
* This item should be assembled on a soft surface to prevent scratching the finish
during assembly
* This item may require periodic tightening
Part List and Hardware List
PIECE QUANTITY
A2X
B4X
H1 16X
H2 1X
Socket Screw 6x0.5x35mm
M6X35mm
Allen key
DESCRIPTION PICTURE Weight Capacity:30LBS
Shelf
Metal Frame
Warning:Don not stand on shelve
WARNING
Warning:Don not over torque screws

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 15 minutes.
Tools Required for Assembly (included): Allen Key
PREPARATION
2
1
Step 1 Step 2
Attach the Shelf(B1) to the Metal frame (A1&A2), using Socket Screw(H1) Attach the Shelf(B2) to the Metal frame (A1&A2), using Socket Screw(H1)
Tighten with Allen key(H2) Tighten with Allen key(H2)
Step 3 Step 4
Attach the Shelf(B3) to the Metal frame (A1&A2), using Socket Screw(H1) Attach the Shelf(B4) to the Metal frame (A1&A2), using Socket Screw(H1)
4
3
() ( ), g
()
() ( ), g
()
Tighten with Allen key(H2) Tighten with Allen key(H2)

WARNING
Serious or fatal crushing injuiries can occur from furniture tip over. To prevent tipover:
Install tipover restraint provided.
Place heaviest items in the lower drawers.
Unless specifcially desgined to accommodate, do not set TVs or other heavy objects on top of this product.
Never allow children to climb or han
g
on drawers
,
doors or shelves.
Never o
p
en more than one drawer at a time.
Do not defeat or remove the drawer interlock s
y
stem.
Use of ti
p
over restraints ma
y
onl
y
reduce
,
but nto eliminate
,
the risk of ti
p
over
.
PIECE QUANTITY
H3 2 PCS
H4 2 PCS
H5 2 PCS
H6 2 PCS
Anti-Tip Kit
Part List and Hardware List
DESCRIPTION PICTURE
Nylon Strap
Long Screw
M4*25mm
Plastic Screw Anchor
Wall Bracket
1. Mark the location on the wall for mounting the second bracket "H6". Drill a 1/4 inch hole in the wall and insert the plastic screw anchor "H5".
Secure the bracket to the wall using the long screw "H4".
2. Place the furniture so the bracket on the back edge of unit is lined with the bracket on the wall.
3. Lace the end of the nylon strap "H3" down through each of the bracket. Bring both ends together and slide the beaded end of the strap through the keyhole
shaped slot on the other end. Pull down on the beaded end until it snap-locks into the keyhole.
4. Check to make sure the strap is securely laced and locked to the brackets.
5. Complete!
Assembly Steps