Safe Fleet MVQ-V75V100-MTPLT User manual

MVQ-V75V100-MTPLT Mounting Bracket
Installation Guide
© Safe Fleet | February 2023 | All rights reserved | Part #: 700-1178 R3
Service & Support
If your MVQ-V75V100-MTPLT mounting bracket is to be returned for service,
please contact the Safe Fleet technical support team, provide the part and/or
serial # of your unit, and ask for a Return Merchandise Authorization (RMA)
number.
An RMA # allows the support team to better track your product when it comes
in for service. Please show the RMA # on the outside of the package.
ANY PRODUCT SENT WITHOUT AN RMA # MAY BE REFUSED!
Technical Support
Phone: [phone] Email: PTsupport@safeeet.net
2002/96/EC (WEEE directive): This product cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return the product to your local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection points, for more information, see www.recyclethis.info.
2006/66/EC (battery directive): This product does not contain batteries.
Documentation
and Warranty
Additional copies of this
guide along with other
documentation and product
warranty can be found on
the Safe Fleet Community
website: https://community.
safeeet.net
This guide provides instructions on how to use the MVQ-V75V100-MTPLT universal mounting bracket when
installing your public display monitor.
About the mounting bracket
The MVQ-V75V100-MTPLT bracket is intended for mounting monitors that comply with the following standard
VESA mounting hole patterns:
• 75mm x 75mm
• 100mm x 100mm
What is included
The MVQ-V75V100-MTPLT mounting bracket assembly contains the following components:
TIP: Accessing retaining screws
We recommend using a magentic-tipped long screwdriver or a multi-driver tool with a bit extension
to access the retaining screws.
Wall mount bracket
assembly 1pc
Includes:
1 VESA plate
1 wall plate
2 retaining screws
M4x8mm VESA mounting
screw - 4 pcs
M4x6mm VESA mounting
screw - 4 pcs
Washer - 4 pcs
 NOTE: Wall mounting screws
Due to the variations in installation scenarios, the screws required to secure the wall plate to the mounting
surface are to be provided by the customer.
CAUTION! Retaining screws
To ensure safety, both retaining screws must be installed.
For use with the 10.4” Public
Display Monitor
For use with the 15.6” Public
Display Monitor
For use with both the 10.4” and
15.6” Public Display Monitors

Fold Here
How to install
Typically, you should proceed with bracket installation after you have connected all the cables to the monitor.
1 Disassemble the bracket
Disassemble the mounting bracket. Using a Phillips screwdriver, remove the retaining screws from the
sides and the bottom of the wall mount bracket assembly. Separate the VESA (monitor) plate from the
wall plate.
2 Mark and drill holes in mounting surface
After determining the location of the monitor according to the installation requirements, place the wall
plate at against the mounting surface. Level the plate, and mark the holes with a pencil. Drill holes into
the mounting surface.
3 Mount wall plate
Hold the wall plate against the mounting surface so the wall plate holes are aligned with the drilled
holes. Insert the wall mounting screws into the holes and nger tighten them. Fully tighten the screws
using an appropriate tool.
4 Attach VESA plate
Attach the VESA plate to the monitor using the supplied VESA mounting screws and washers.
5 Mount monitor
Position the monitor so the VESA plate is vertically aligned with the wall plate. Slide the VESA plate on
top of the wall plate and carefully lower the monitor into place. Replace the retaining screws on the
sides of the mounting bracket assembly.
Wall plate
VESA plate
Retaining screws