Safe-t-Cover 800S Series User manual

ASSEMBLY INSTRUCTIONS
READ CAREFULLY

Safe-T-Cover
1-800-245-6333
HCF800S-2
1. Center a 6" thick concrete base around installed BFP.
A. Place expansion material around riser pipe and place conduit for electrical power before placing
concrete. CONCRETE SHOULD BE FINISHED ABSOLUTELY LEVEL, FLAT AND
SMOOTH. Allow concrete to cure.
B. Mark concrete with outside dimensions of enclosure. Center enclosure around BFP.
2. Using four (4) hexhead screws for each section assemble each "A-B" (end and side)
sections thru holes provided. Set on marked concrete base (FIG 2).
3. Set "D1" (roof) panel on "A-B" sections. Using two (2) hexhead screws fasten thru holes provided (Fig 1).
A. “Temporarily” place “F” (center) post in position.
4. Position “D2” (roof) panel over edge of “D1” (roof) panel and set on other “A-B” section. Using two (2)
hexhead screws fasten thru holes provided (Fig 1).
5. On top inside of roof, using ten (10) hexhead screws attach Inner Roof Connection Bracket (Fig 1E) to
“D1” (roof), “D2” (roof) and both “F” (side) posts. (This will cover the wood members in the center of
the top and secure the top to the “F” post.)
6. A. Using one (1) hexhead screw attach Outside Corner Anchoring Brackets to "A-B" sections. Fasten
bracket to concrete using one anchor for each bracket (FIG 1A).
B. Square the “A-B” corners. Align the “B” panels so that they form a straight line. Using one (1) hexhead
screw and one (1) hit pin for each bracket attach Inside Anchoring Brackets to "B" panels and concrete
(FIG 1B).
C. Insert Inside Roof Clips in "D" (roof) panel. Using one (1) hexhead screw in each clip attach clip to
"B" (side) panel (FIG 1C).

Safe-T-Cover
1-800-245-6333
HCF800S-3
7. A. Align "F" (center) post in the center of the opening.
B. Install Inside Anchoring Brackets (Fig 1B) at bottom of the “F” posts.
8. On outside at “D1-D2” (roof) seam, install Roof Cover Plates (Fig 1D) on each side of enclosure. (Fig
1D).
9. Set "C" panels and lock in place. (Solid "C" panel to be the ACCESS DOOR PANEL).
10. Provide ground-fault interrupter device in electrical circuit according to applicable codes. Install heater as
per manufacturer's instructions and governing local and national codes.
11. For maximum protection it is suggested that the area between the bottom of the enclosure and the
concrete base be caulked with the exception of the "C" panels. DO NOT CAULK THE BOTTOM OF
THE "C" DOOR PANELS.
REMOVE MASKING FILM IMMEDIATELY
AFTER INSTALLATION.
If these panels get wet when the film is still on, water will
irreversibly stain the panels. Summertime heat will bake the
film on the panels.

Safe-T-Cover
1-800-245-6333
HCF800S-4
CONTENTS
Model No. 800S-Series
Model No. 800TS-Series
2- "A" (end) Panels
4- "B" (side) Panels
1- "C" (drain door) Panel
3- "C" (solid access) Panels
2- "D" (roof ) Panels
2- "F" Panels
1- Inner Roof Connection Bracket (With tabs for “F” posts)
2- Roof Cover Plates
4- Outside Corner SS Anchoring Brackets (2½” x 2 ½”)
6- Inside Aluminum Anchoring Brackets (3” x 3”)
4- Inside Roof Clips
10- Wedge Anchors
42- Screws
1- Masonry Bit
1- Magnetic Chuck
TOOLS NEEDED
Hammer
Drill
7/16” Wrench