SAFERA PCU3 User manual

INSTALLATION MANUAL
SAFERA Siro R-line stove guard
Power control units:
PCU3
PCU3-W
PCU5.1-U
PCU5.1-P
20812 V4.5.0 ENG SIRO R-LINE

32
1. PREPARATIONS
Check the product and the contents of the
package before installation:
• Sensor unit with mounting bracket Ⓐ
• Power Supply Ⓓ
• Power Control Unit Ⓒ
• User and Installation Guides
• Declaration of Conformity
ѥWARNING
Please contact your vendor if you notice
anything unusual about the appliance.
CONTENTS
1. Preparations
2. Installation
3. Troubleshooting
4. Optional: Installing the Water Leakage
Sensor
Follow these instructions carefully and
pay particular attention to the instructions
marked in the following way:
ѥWARNING
Follow instructions marked with a war-
ning accurately to prevent injury to per-
sons and damage to property.
⚐ATTENTION
Follow instructions marked with a note
carefully to prevent damage to property.
ѧHINT
Hints give you useful advices on using the
appliance.
WARNINGS
ѥWARNING
Read user and installation manual before
using or installing the appliance.
Install and check the application accor-
ding to the instructions. SAFERA is not
liable for any damages or expenses caused
by inappropriate installation.
Check that the Stove Guard is compatible
with the cooker (see section 1.1).
If the network cable is damaged, it must
be replaced by the service personnel of
the manufacturer or their representative
to avoid hazards.
All electrical connections must be carried
out by a qualied electrician.
⚐ATTENTION
If the appliance was stored in a cold spa-
ce, it must be allowed to warm up to room
temperature before connecting it to elec-
tric network.
1.1 Compatibility
SAFERA Stove Guard is compatible with
most electrical cookers, hobs and ovens
meant for household use:
• Traditional cast-iron cookers and hobs
• Ceramic cookers and hobs
• Induction cookers and hobs
• Cookers and hobs equipped with a ti-
mer, afterheat indicator, child proof
lock or integrated switch-off system
SAFERA Siro R is compatible with cookers
no wider than 90 cm, see chapter 2. Instal-
lation step 1/6.
1.2 Control Panel
❶ Child proof lock button
❷ OK button
❸ Indicator light for child proof lock
❹ Indicator light for normal activity
❺ Warning light for cooktop hazard
❻ Warning light for water leakage
❼ Adjustment mode button
❽ Indicator light panels
❾ Sensor
8
91
3
72
4
5 6
Ⓐ
Ⓒ
Ⓓ

54
Install the Cental Unit Ⓐon the wall above the cooktop and follow these dimensions:
⚐ATTENTION
The Sensor unit Ⓐis plugged into the wall
socket with its own power supply Ⓓ.
Min 8 mm Min 5 mm
200 mm
12
”KLIK”
3
”KLIK”
4
5
Cooker width Installation
Height
Max. 60 cm 45 - 75 cm
60 - 90 cm 60 - 75 cm
Width
Align the Sensor unit ±15
mm with the centre of
the cooktop.
Depth
Align the sensor of
Sensor unit (white lens)
±100 mm with the centre
of the cooktop.
INSTALLATION - STEP 1/6 Mount the Sensor unit

76
Install the Power Control Unit according to the following instructions.
INSTALLATION - STEP 2/6 Mount the Power Control Unit Ⓒ.
PCU5.1-U
Fixed 1-phase connection.
See pages 12-13.
PCU3-W
Perilex-connectors.
See pages 10-11.
PCU3
Fixed 3-phase connection.
See pages 8-9.
PCU5.1-P
3-pin plug.
See pages 14-15.

98
ѥWARNING
Make sure that there is no power supply to
the cooker and the oven by removing their
fuses. Also ensure that the cooker is swit-
ched off.
OUT-wires are always energized when
the power control unit is connected to the
electrical network. If a wire is loose, it must
be properly covered.
If the element voltage of the cooker is 400
V, the fuse can only be maximum of 10 A. If
the element is 230 V, the fuse can only be
maximum of 16 A.
Do not install the power control onit to ex-
cessive heat: Operational ambient tempera-
ture is +5 … +40°C.
⚐ATTENTION
Power control unit Ⓒrequires a neutral
wire to operate.
Install the power control unit Ⓒ so that it
is not exposed to moisture. Check that all
cables can move freely.
ѧHINT
If you are replacing a cooker, press the ad-
justment mode button ❼ for ve seconds
until you hear a signal. Continue the
installation according to step 3/6.
OUTIN
PE
L/N
L
PE
N
L
L
230V 16A
400V 10A
230V 16A
400V 10A
230V 16A
400V 10A
MAX
MAX
MAX
L1
L2
L3
MICRO DISCONNECTION
OFF
IN
5 x 2,5 mm2
0,7 m
OUT
5 x 2,5 mm2
1,3 m
180 mm
60 mm
130 mm
Optional
water sensor
connection.
See chapter 4.
Remove the fuses to the cooker and oven.
Mount the power control unit Ⓒ on the wall behind the cooker or into the cabinet
next to the cooker.
Couple the protective earth rst (PE).
Couple the other wires.
Don’t reconnect the power to the cooker yet.
Installation
3
4
5
2
1
PCU3 - INSTALLATION
Fixed 3-phase connection.

1110
ѥWARNING
Make sure that there is no power supply to
the cooker and the oven by removing their
fuses. Also ensure that the cooker is swit-
ched off.
OUT-wires are always energized when
the power control unit is connected to the
electrical network. If a wire is loose, it must
be properly covered.
If the element voltage of the cooker is 400
V, the fuse can only be maximum of 10 A. If
the element is 230 V, the fuse can only be
maximum of 16 A.
Do not install the power control onit to ex-
cessive heat: Operational ambient tempera-
ture is +5 … +40°C.
⚐ATTENTION
Power control unit Ⓒrequires a neutral
wire to operate.
Install the power control unit Ⓒ so that it
is not exposed to moisture. Check that all
cables can move freely.
OUTIN
PE
L/N
L
PE
N
L
L
230V 16A
400V 10A
230V 16A
400V 10A
230V 16A
400V 10A
MAX
MAX
MAX
L1
L2
L3
MICRO DISCONNECTION
OFF
66 mm
146 mm
313 mm
700 mm
Optional
water sensor
connection.
See chapter 4.
280 mm
126 mm
Remove the fuses to the cooker and oven.
Mount the power control unit Ⓒ on the wall behind the cooker or into the cabinet
next to the cooker.
Install the power control unit Ⓒ with Perilex-connectors.
Don’t reconnect the power to the cooker yet.
Installation
PCU3-W - INSTALLATION
3-phase, Perilex-connectors.
ѧHINT
If you are replacing a cooker, press the ad-
justment mode button ❼ for ve seconds
until you hear a signal. Continue the
installation according to step 3/6.
3
4
2
1

1312
ѥWARNING
Make sure that there is no power supply to
the cooker and the oven by removing their
fuses. Also ensure that the cooker is swit-
ched off.
OUT-wires are always energized when
the power control unit is connected to the
electrical network. If a wire is loose, it must
be properly covered.
Do not install the Power Control Unit to ex-
cessive heat: Operational ambient tempera-
ture is +5 … +40°C.
⚐ATTENTION
Install the power control unit Ⓒ so that it
is not exposed to moisture. Check that all
cables can move freely.
IN
3 x 4 mm2
OUT
3 x 4 mm2
180 mm
60 mm
130 mm
Optional water
sensor connection.
See chapter 4.
Remove the fuses to the cooker and oven.
Mount the power control unit Ⓒ on the wall behind the cooker or into the cabinet
next to the cooker.
Couple the protective earth rst (PE).
Couple the other wires.
Don’t reconnect the power to the cooker yet.
Installation
PCU5.1-U - INSTALLATION
Fixed 1-phase connection.
OFF
OUTIN
PE
L/N
L
PE
N
L
230V MAX. 25A
MICRO DISCONNECTION
ѧHINT
If you are replacing a cooker, press the ad-
justment mode button ❼ for ve seconds
until you hear a signal. Continue the
installation according to step 3/6.
3
4
5
2
1

1514
59-79 mm
73 mm 60 mm
68-80 mm
ѥWARNING
Make sure that there is no power supply to
the cooker and the oven by removing their
fuses. Also ensure that the cooker is swit-
ched off.
OUT-wires are always energized when
the power control unit is connected to the
electrical network. If a wire is loose, it must
be properly covered.
⚐ATTENTION
Install the power control unit Ⓒ so that it
is not exposed to moisture. Check that all
cables can move freely.
OFF
OUTIN
PE
L/N
L
PE
N
L
230V MAX. 25A
MICRO DISCONNECTION
PE
L
L
N/L
L/N
3
4
PE
56
7
2
1
9Don’t reconnect the power to the
cooker yet.
Optional water
sensor connection.
See chapter 4.
Connect the stove with
3-pin plug.
8
PCU5.1-P - INSTALLATION
3-pin plug.
ѧHINT
If you are replacing a cooker, press the ad-
justment mode button ❼ for ve seconds
until you hear a signal. Continue the
installation according to step 3/6.

1716
Connect the power supply Ⓓ to the
Sensor unit Ⓐ: indicator light panels
❽are lit in purple.
Put back the fuses for the cooker and
the oven. The Power Control Unit Ⓒ
will now contact the Sensor unit Ⓐ
which gives a sound signal (•••).
Press the adjustment mode button
❼: indicator light panels ❽start
blinking purple-blue.
2
ѧHINT
You can re-start the installation process
anytime by pressing the adjustment mode
button ❼ for ve seconds until you hear
the signal.
1
INSTALLATION - STEP 3/6 Set up the wireless connection
When the indicator light panels ❽start blinking yellow-green, you need to calibrate
the system. Choose from the two options:
Check that the indicator light for normal activity ❹ blinks every ve seconds.
OPTION 1:
Cooker and oven are connected
to the Power Control Unit Ⓒ.
1
2
OPTION 2:
Only cooktop is connected to
the Power Control Unit Ⓒ.
Turn on the biggest cooker plate with
maximum power and press the OK-
button ❷. When you hear a
sound signal (•••), turn off
the cooker.
ѧHINT
With induction cooker, use a compatible
dish.
Turn on the oven and press the child
proof lock button ❶. When you hear
a sound signal (•••), turn off
the oven.
Ⓒ
ⒸⒸ
tai
or
INSTALLATION - STEP 4/6 Calibrate the system
3
ON

1918
Adjust the alarm limit according to the reference table above. The default alarm limit
is 6.
First, go to the adjustment mode:
2
Check the closest
recommended alarm
limit from the refe-
rence table on the right.
The range is 1-12:
1 = reacts fastest
12 = reacts slowest
Then, adjust the alarm limit:
Lower the alarm limit
(-1): press the lock
button ❶.
Raise the alarm limit
(+1): press the OK-
button ❷.
= vakioasetus
1
Press the adjustment mode
button ❼: indicator light
panels ❽ lit white.
12
11
10
9
8
7
6
5
4
3
2
1
INSTALLATION - STEP 5/6 Adjust the alarm limit
When you adjust the
alarm limit, the new
alarm limit is indica-
ted as shown in the table on
the right.
3
ѥWARNING
Do not set the alarm limit higher than 9
during the installation.
If the alarm limit is set too high, the app-
liance may fail to detect a hazardous situ-
ation in time.
ѧHINT
You may check the alarm
limit by pressing the ad-
justment mode button ❼
twice.
Location of the Cooker Installation
Height
Alarm Limit
(1-12)
In a corner 75 cm 6*
65 cm 7
55 cm 8
45 cm 9
Next to a wall 75 cm 5
65 cm 6*
55 cm 7
45 cm 8
In an island 75 cm 4
65 cm 5
55 cm 6*
45 cm 7
* Default
Color of the indicator
light panels ❽
Number of
beeps Alarm Limit
Red
••• ••• 12
••• •• 11
••• • 10
••• 9
•• 8
• 7
Blue
••• ••• 6 (default)
••• •• 5
••• • 4
••• 3
•• 2
• 1

2120
Check the working order of the appliance and ll in the installation checklist:
≅All the burners of the cooker cause a child proof lock
alarm.
≅The oven (if connected) causes the child proof lock
alarm. The sound signal is lower than the signal from
the cooker child proof lock.
≅The child proof lock turns off the oven and all the bur-
ners.
≅The indicator light panels ❽are not lit red after
installation.
≅The alarm limit is set according to the cooker location
_______________________________
Installation date
_______________________________
Installation place
_______________________________
Installer
INSTALLATION - STEP 6/6 Check-list 3. INSTALLATION TROUBLESHOOTING
Problem Remedy
Installation is not proceeding
as expected.
You can re-start the installation process anytime by
pressing the adjustment mode button ❼ for ve seconds
until you hear the signal and continue from step 3/6.
The sensor unit Ⓐis not
responding to any button and
none of the indicator lights
are lit.
Ensure that the power supply Ⓓis connected correctly to
the wall socket and that the socket has power.
None of the cooker plates
cause a child proof lock alarm.
The wireless connection has not been properly made: redo
the installation starting from step 3/6.
The appliance turns off the
power from the cooker, but
the power comes back on
immediately.
Make sure that the Power Control Unit Ⓒis connected
correctly – in other words, the cooker is connected to the
OUT cable.
If the light panels ❽are
constantly lit red after the
installation, the appliance is
faulty.
See user manual chapter 5. Troubleshooting

2322
4. INSTALLING THE WATER LEAKAGE
SENSOR (optional)
Stove Guard can be equipped with max.
four SAFERA Water Leakage Sensors. The
sensors are placed in the typical leakage
areas, e.g. under the dishwasher or sink.
Attach the sensors Ⓕin place.
1
ѧHINT
If the sensor is left wet, the appliance will
give another alarm in an hour after signing
off the previous one.
Attach the plug Ⓖ of the leakage
sensor to the Power Control Unit Ⓗ.
2
If there is an extra sensor, its plug Ⓖ
is connected to the connector Ⓘof
the previous sensor.
3
Check the operation of the furthest
sensor Ⓕby placing a damp paper to-
wel against it for 15 seconds. When
the water is detected, the Sensor unit Ⓐ
gives a sound signal, the warning light for
water leakage ❻blinks and light panels ❽
blink blue.
4
Reset the leakage alarm by pressing
the OK button ❷. Clean and dry the
sensor.
5
C
GH
I
F

24