SafeTrust SABRE User manual

SABRE Module Quickstart Guide
Last Updated: February 2022
8830-000

Contents
Safetrust Inc. | safetrust.com
[e-mail]
In the box
What you'll need
Installation
Configuration
Regulatory
Support
01
02
03
04
05
06

01
Safetrust Inc. | safetrust.com
[e-mail]
In the box

SABRE Module
Safetrust Inc. | safetrust.com
[e-mail]
The SABRE Module is a plug-in
installation meaning there is no
rewiring necessary.

02
Safetrust Inc. | safetrust.com
[e-mail]
What you'll need

A few minutes of your time
Snake eye screw driver to remove security screw from the base of the reader
Safetrust Inc. | safetrust.com
[e-mail]

03
Safetrust Inc. | safetrust.com
[e-mail]
Installation

Safetrust Inc. | safetrust.com
[e-mail]
Remove the mounting screw and pull the reader in an ‘out and upward’ motion to
remove it from the wall mount bracket.

Safetrust Inc. | safetrust.com
[e-mail]
Position the SABRE MODULE onto the reader's connector and press firmly to make
a solid connection. (Note that the reader's connector is below the wiring —
pictured above as a terminal strip but the wiring may alternatively be pigtail.)

Safetrust Inc. | safetrust.com
[e-mail]
Once a firm connection is made between the MODULE and the connector, the
MODULE will receive power and will be operational within 5 seconds.
Note: Install of the SABRE Module will generate a reboot of the HID Reader and the
SABRE Module. You will notice a series of beeps, from the HID Reader when the
SABRE module reboots.

04
Safetrust Inc. | safetrust.com
[e-mail]
Configuration

Safetrust Inc. | safetrust.com
[e-mail]
Open the Safetrust Wallet APP and select Manage Sensor tab. Make sure your
system admin has set you up with this role.

Safetrust Inc. | safetrust.com
[e-mail]
With the Admin Installer tab open from the App, bring the phone in range of the
SABRE Module and once visible from the App, highlight and select “Configure”.

Safetrust Inc. | safetrust.com
[e-mail]
• Choose an Identity System.
• Specify the Type of access from the dropdown (eg. Door, Gate etc.)
• Assign a short Name and Description using alphanumeric characters.
• Choose an Output for the sensor (the default is set to Wiegand).

Safetrust Inc. | safetrust.com
[e-mail]
When the Module information is saved successfully to Credential Manager and
assigned to the Identity System, the new description will appear in the Manage
Sensor tab with a unique serial number assigned.

05
Safetrust Inc. | safetrust.com
[e-mail]
Regulatory
Information

Safetrust Inc. | safetrust.com
[e-mail]
FCC: This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Canada Radio Certification: This device complies with Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
CE Marking: Safetrust hereby declares that these proximity readers are in
compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.

06
Safetrust Inc. | safetrust.com
[e-mail]
Support
Thank you for purchasing the
Safetrust SABRE Module.
If for any reason you need assistance
with your installation, please contact
your local Sales representative .
Sincerely -
The Safetrust Team

www.safetrust.com/support