If this Stubby® worklight malfunctions or is in need of repairs, send to:
General Manufacturing, Inc.
1100 S. Morgan St.
Bluffton, IN 46714
Phone: 260-824-3440 • Fax: 260-824-3448 • Internet: www.saftlite.com
"AUTION, IMPORTANT SAFETY INSTRU TIONS - This portable lamp has a polarized plug
(one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will
fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. Never use an extension cord unless plug can be
fully inserted. Do not alter the plug."
"ATTENTION,INSTRU TIONS IMPORTANTES DE SE URITE -CETTE LAMPE PORTATIVE A
UNE FICHE POLARISANTE (UNE LAME EST PLUS GRANDE QUE L'AUTRE) COMME
CARACTERISTIQUE POUR REDUIRE LE RISQUE DE CHOC ELECTRIQUE. CETTE FICHE
N'ENGAGE Q'UNE PRISE POLARISANTE. SI LA FICHE N'ENGAGE PAS COMPLETEMENT
LA PRISE, ALORS RENVERSER LA, SI ELLE N'ENGAGE TOUJOURS PAS, METTER VOUS
EN RAPPORT AVEC UN ELECTRICIEN QUALIFIE. NE JAMAIS UTILISER AVEC UN
PROLONGATEUR SI LA FICHE N'ENGAGE PAS COMPLETEMENT. NE CHANGER PAS LA
FICHE."
RELAMPING INSTRUCTIONS
1. DIS ONNE T THE UNIT FROM ITS POWER SOUR E (UNPLUG).
. Lamp will be removed from cord end so it is not necessary to do anything at the switch
end.
3. Slide end cap down the cord about 6”. Remove the two screws that are now exposed.
4. The lamp assembly will now slide out the end of the tube. To assist in its removal, use a
pair of needle nose pliers to grip the square base of the lamp and pull. The bottom
lampholder will come out with the lamp.
5. Push the lamp through the lampholder with your thumb against the square base. It must
go out the front of the lampholder and the new lamp inserted the same way. Be sure the
wireways (two grooves in lampholder) are in the same position with respect to the new
lamp as they were with the lamp being removed.
6. Insert lamp with lampholder into tube being sure white wires from switch are in the
wireway groove. Using your thumb, push lamp and lampholder until it stops. (about 1/4”)
7. Re-plug terminal onto pins of lamp. Either terminal can go onto either pin.
8. Re-install end bracket and end cap in the same manner as when they were removed.
Re-install the two screws that were taken out in step 3. Re-lamping is now complete
90 Day Warranty
General Manufacturing Inc. warrants to the purchaser of this new light that it was
thoroughly tested and inspected and found to be in perfect working order before leaving
our factory. If within 90 days from the date of purchase, any part of this worklight proves
to be defective in material or workmanship, such defective part will be repaired or
replaced (company option) free of charge. The company's liability in all events is limited
to the purchase price paid.
The warranty does not apply to the fluorescent lamp nor does it apply to damage,
alteration, misuse or abuse not attributed to General Manufacturing, Inc., its
representatives, dealers or their employees. This warranty does not apply if the product
is mishandled or operated at a voltage exceeding, that shown on the reflector. This
warranty pertains to any light that may be termed by manufacturers, as a service unit.
General Manufacturing, Inc. has made a diligent effort to illustrate and describe the
products in its literature accurately, however such illustrations and descriptions are for
the sole purpose of identification and do not express or imply a warranty that the
products will necessarily conform to the illustrations or descriptions.
When returning product for warranty repair, please provide: from whom purchased,
date of purchase, and attach receipt or give invoice number.
Form No. 903 -7009 - Rev. 01/17/ 00
