Sage Big Squeeze SJS700 User manual

the Big Squeeze™
SJS700
EN QUICK GUIDE DE KURZANLEITUNG
FR GUIDE RAPIDE NL SNELSTARTGIDS
ES GUÍA RÁPIDA

2
SAGE®
RECOMMENDS
SAFETY FIRST
At Sage®we are very safety
conscious.We design and
manufacture consumer
products with the safety of
you, our valued customer,
foremost in mind. In
addition we ask that you
exercise a degree of care
when using any electrical
appliance and adhere to the
following precautions.
IMPORTANT
SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE
FOR FUTURE REFERENCE
• A downloadable version of this
document is also available at
sageappliances.com
• Before using for the rst time
ensure your electricity supply
is the same as shown on
the label on the underside
of the appliance.
• Remove and safely discard
any packaging materials before
rst use.
• To eliminate a choking hazard
for young children, safely
discard the protective cover
tted to the power plug.
• This appliance is for household
use only. Do not use the
appliance for anything other
than its intended use. Do not
use in moving vehicles or boats.
Do not use outdoors.Misuse
may cause injury.
• Fully unwind the power cord
before operating.
• Position the appliance on
a stable, heat resistant, level,
dry surface away from the edge
and do not operate on or near
a heat source such as a hot
plate, oven or gas hob.
• Vibration during operation may
cause the appliance to move.
• Do not let the power cord hang
over the edge of a bench or
table, touch hot surfaces or
become knotted.
• Always ensure the appliance
is turned OFF, unplugged at
the power outlet and has been
allowed to cool before cleaning,
attempting to move or storing.
Contents
2Important Safeguards
5Components
6Assembly
9Operation
10 Care & Cleaning
12 Troubleshooting
15 Guarantee

3
EN
• Always turn the appliance to
the OFF position, switch o at
the power outlet and unplug
at the power outlet when the
appliance is not in use.
• Do not use the appliance if the
power cord, plug, or appliance
becomes damaged in any way.
If damaged or maintenance
other than cleaning is
required, please contact Sage
Customer Service or go to
sageappliances.com
• Any maintenance other than
cleaning should be performed
by an authorised Sage®
service centre.
• Children should not play with
the appliance.
• Cleaning of the appliance
should not be carried out by
children unless they are 8 years
or older and supervised.
• The appliance and its cord
should be kept out of reach
of children aged 8 years
and younger.
• The installation of a residual
current safety switch is
recommended to provide
additional safety when using
all electrical appliances.
Safety switches with a rated
operating current not more
than 30mA are recommended.
Consult an electrician for
professional advice.
• Always ensure the appliance is
properly assembled before use.
The appliance will not operate
unless properly assembled.
• Do not use the appliance
on a sink drain board.
• Keep hands, ngers, hair,
clothing as well as spatulas
and other utensils away from
moving or rotating parts during
operation.
• Do not use the appliance
for anything other than food
and/or beverage preparation.
• In order to avoid the possible
hazard of the appliance starting
by itself due to inadvertent
resetting of the overload
protection, do not attach an
external switching device
(such as a timer) or connect the
appliance to a circuit that can
regularly switch the appliance
on and o.
• Carefully read all instructions
before operation and save for
future reference.
• The appliance can be used by
persons with reduced physical
or mental capabilities or a lack
of experience and knowledge,
only if they have been given
supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved.
• This appliance shall not be
used by children.
• Do not leave the appliance
unattended when in use.

4
• Do not push food into the feed
chute with your ngers or other
utensils.Always use the food
pusher provided. Do not place
hand or ngers into the food
chute when it is attached to
the appliance.
• Do not juice stone fruit unless
seeds and/or stones have
been removed.
• Do not operate the juice
extractor without the pulp
and juice container in place.
• Do not use the juice extractor
if the juicing screw is damaged.
• Do not operate the machine
longer than 20 seconds before
inserting ingredients.
The symbol shown
indicates that this appliance
should not be disposed of
in normal household waste.
It should be taken to a local
authority waste collection centre
designated for this purpose or to
a dealer providing this service.
For more information, please
contact your local council oce.
To protect against electric
shock, do not immerse the
power plug, cord or appliance
in water or any liquid.
SAVE THESE INSTRUCTIONS

5
EN
Components
Feeding
Basket
Feeding
Tube
Detachable
A. Feeding Tube & Basket
For dierent sizes of produce.
B. Juicing Bowl
C. Pulp Cup
D. Drum Lid
E. Detachable Smart Cap
F. Juice Jug
G. Motor Body
H. Rotation Wiper
I. Strainer
J. Juicing Screw
K. Pusher
L. Cleaning Brush
Rating Information
220–240V~ 50/60Hz 240W
A
B
E
D
G
F
C
H I J K L

6
TOP SET ASSEMBLY
Align the dots on each part and assemble
in the order shown. Once assembled, turn the
drum lid clockwise to close.
Assembly
BEFORE FIRST USE
Before using your Juicer for the  rst time, remove
any packaging material and promotional labels.
Ensure the power is in the OFF position, the juicer
is switched o at the power outlet and the power
cord is unplugged.
Wash bowl and juicing tools in warm soapy water
with a soft cloth. Rinse and dry thoroughly.
When  rst using your appliance, you may notice
an odour coming from the motor. This is normal
and will dissipate with use.
TOP-SET AND BODY ASSEMBLY
Place the drum lid on the juicing bowl. Align the
red dot on the drum lid with the ALIGN mark
on the body and turn to the LOCK position.

7
EN
ASSEMBLY
1. Firmly insert the compression silicone into
the slot below the pulp spout.The Juicer
may leak if not assembled properly.
2. Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot on the
strainer is aligned with the red dot on the
juicing bowl.
3. Place the juicing screw into the strainer.Turn
and press down on it until it clicks into place.
The juicing screw needs to be locked in place
in order to close the drum lid.
4. Place the drum lid on to the juicing bowl
aligning the dot on the drum lid with the
red dot on the juicing bowl.
TIP
For easy assembly hold the drum lid by grabbing
the feeding tube and turn clockwise as shown
in the illustration.
5. Align the red dot on the drum lid with the
ALIGN mark on the body and turn to the
CLOSE position.

8
6. Align arrows on drum lid and motor body.
NOTE
The juicer will not operate if the down arrow
on the drum lid is not completely aligned with
the CLOSE mark on the body.
7. Place the pulp cup under the pulp spout and
place the juice cup under the juice spout
as shown in the illustration.
Detachable

9
EN
Operation
USING YOUR JUICER
1. After preparing the ingredients, plug the
power cord into a wall outlet. Do not touch
the power cord with wet hands. It may cause
electrical shock, short-circuit, or  re.
2. Press the FORWARD button to operate.

Forward: Pulls down and slowly masticates
the ingredients.
Reverse: Pushes the ingredients back up
to dislodge them.The REVERSE button
only works while holding down the switch.
3. Insert the prepared ingredients into the
feeding tube, one piece at a time. If large
quantity of ingredients are put into the
feeding tube, it can cause the juicer to stop
Remove hard seeds or pits in fruits.
When juicing frozen fruits, completely
thaw before juicing.
HARD VEGETABLES & HIGH FIBRE
FOODS (E.G. CARROTS, BEETROOT,
& SPINACH)
Insert into the feeding tube.
Tough and  brous ingredients: Cut to 2cm
wide and 5cm long.
Fibrous leafy vegetables: (celery, kale, collard
greens, etc.): Cut the stems into 5cm long and
bundle up the leafy part as you insert them into
the juicer.
SOFT FRUITS & VEGETABLES
(E.G. APPLES, ORANGES & TOMATOES)
Insert into the feeding basket.
Soft ingredients: Cut ingredients into 1–4
pieces. Insert the prepared ingredients into the
feeding basket and push down the ingredient
with the basket lid to extract.

10
Care & Cleaning
4. Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
NOTE
Immediately clean the juicer after each use.
If remaining residue in the juicer dries up,
it can make disassembling and clean-up di cult.
The excess build up can cause poor performance
in future uses. For easier disassembly, place the
top-set in the sink and run the water through from
the top of the top-set.
We do not recommend to wash any parts of the
juicer in the dishwasher.Washing parts in the
dishwasher can cause damage to them due
to prolonged exposure to harsh detergents,
hot water and pressure.
5. Place the juicing bowl under running water
and unplug the compression silicone to clean
the pulp spout.
Extract all the remaining pulp in the juicing bowl
before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted. Then  ll the juicing bowl with water
and run the juicer before opening the drum lid.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times to
dislodge.Then place both hands on the drum
lid and  rmly press down while simultaneously
turning the drum lid to open.
CLEANING THE JUICER
1. Switch OFF and unplug the power cord
from the wall outlet.
2. Turn the drum lid counter clockwise to open.
WARNING
When moving the appliance, do not lift by
grabbing the feeding tube. Always lift the
appliance by grabbing the body or handle.
3. Turn the top-set counter clockwise and lift
o the body.

11
EN
6. Under running water, clean the outside of the
juicing screw with a dish scrub. Use the tip of
the cleaning brush to push out any residue in
the crevices on the bottom of the juicing screw.
Thoroughly clean the juicing screw ensuring that
the juicing screw is clean without any residue.
Thoroughly dry the bottom of the juicing screw.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom crevice
of the juicing screw. (If this area isn’t properly
cleaned, it can cause the part to be damaged).
7. Clean the body with a soft damp towel and dry.
If the towel is dripping wet, make sure to
squeeze out the excess liquid before using
it on the juicer.
CLEANING SILICONE PARTS
Clean the rotation wiper under running water.
Thoroughly dry after cleaning. Before assembling
the top-set, ensure that the compression silicone
and silicone ring are  rmly inserted.
If the compression silicone and silicone ring
are not  rmly inserted, juice may leak from the
bottom of the juicing bowl.
COMPRESSION SILICONE
Unplug to clean.
After cleaning,  rmly insert into the slot below
the pulp spout.
SILICONE RING
Remove the silicone ring from the juicing
bowl to clean.
After cleaning, push in the silicone ring with the
smaller surface facing down.
SMART CAP
Remove from the juice spout to clean.
After cleaning, attach the smart cap to the
smart cap silicone on the juice spout.

12
Troubleshooting
PROBLEM EASY SOLUTION
There is no power to
the juicer
• Check if the power cord is properly plugged in.
• Check if the drum lid and the juicing bowl are properly assembled.
• Check if the top-set and the body are properly assembled.
NOTE: Juicer will not operate if parts are not assembled properly.
Low juice yield • Dierent ingredients hold dierent amounts of uid that will yield dierent
amounts of juice.
• If the ingredients are not fresh, they may contain reduced amount of uid,
which will yield less juice. Soak ingredients in cold water for about
30 minutes prior to juicing for the best result.
• Check if the compression silicone is rmly inserted.
• If the ingredient itself has low water content, it may help to soak it in water
before juicing.
• If juicing ingredients with small seeds, after a few servings, it may reduce
the juice yield. For best result, disassemble and wash the top set in
between juicing.
• If there is seed residue on the bottom of the strainer, this can aect juicer
performance and the overall juice yield.
There is too much
pulp in the juice
• To reduce the ne pulp, clean the top-set frequently and extract the pulp.
• Use a mesh strainer and put the juice through it to collect the
unwanted pulp.
• If the strainer and the screw are damaged and aecting the juicer’s
performance, it is recommended the parts be replaced.
• The lifetime of each part may vary depending on length and method of use
and ingredients extracted.
The drum lid will not
close
• Make sure the juicing screw is pushed all the way in to the strainer in order
for the drum lid to close properly.
• If the juicing screw is not properly in position, the drum lid may not close.

13
EN
PROBLEM EASY SOLUTION
Odd noise from the
juicer
• Check if the parts are assembled correctly.Try reassembling the parts
and listen for the odd noise.
• Do not start the juicer unless there are ingredients and/or liquid in it.
• Operating the juicer without ingredients can cause damage to the screw.
• If the juicer is operated without ingredients or liquid, the noise level can
increase and also can lead to damage.
• The friction noise from the juicing screw and the strainer will disappear
when ingredients are inserted into the juicer.
• If the noise occurs when ingredients are inserted into the juicer, check
the size of the ingredients. Do not insert anything over 3cm in thickness.
• Depending on the type of ingredients, the dimensions can be smaller.
• The noise can occur if the juicer is operated on an uneven or slanted
surface. Place the juicer on a horizontally at surface when operating.
The extracted pulp is
very moist
• During the very beginning of extraction, the pulp can be more moist.
• Depending on the ingredient’s condition, the extracted pulp can be
aected; especially when the ingredient is not fresh, the juice can be
extracted with the pulp.
During operation, the
juicing bowl shakes
• The juicing screw and the strainer are set up to crush and squeeze the
ingredients. It is normal for the juicing screw and the strainer to vibrate.
• If the ingredient contains strong bre, the vibration from the top-set
may be stronger.
During juicing, the
juicer stopped
• Check the power cord and make sure it is plugged in correctly.
• Check that all the parts are correctly assembled.
• If too many ingredients are inserted at one time, this can cause the juicer
to stop.
• When the juicer stops because there are too many ingredients inserted in
it, press the REVERSE – OFF – FORWARD button in this order, switching
back and forth 2 to 3 times.The reverse setting will push the ingredients up
and the forward setting will pull the ingredients down.
• After using more than 30 minutes, if the juicer stops due to the overload
protection, let the juicer cool for 30 minutes to 1 hour before juicing again.
• If there are hard seeds within the ingredients, remove them before juicing.
Hard seeds can damage the juicer.
Layers of separation
in the juice
• Depending on the density of the ingredients, the extracted juice may show
layers of dierent juices. It is dierent from separation due to oxidation
caused by juicing with a high-speed juicer.

14
PROBLEM EASY SOLUTION
The drum lid is stuck • After juicing, let the juicer operate for another 30 seconds to extract
the remaining pulp.
• If there is too much pulp in the top-set, this can cause the drum lid to
not open. In this situation, press the REVERSE – OFF – FORWARD
button in the order, switching back and forth 2 to 3 times.Then
place both hands on the drum lid and rmly press down while
simultaneously turning the drum lid to open.
• Pour water down the feeding tube to rinse out the insides and then try
opening the drum lid.
Juice dripping down
the body
• If the compression silicone on the bottom of the juicing bowl is not
plugged in correctly, the juice may seep out on to the juicer body.
Before assembling the parts, check and make sure the compression
silicone is plugged in correctly.
Is it possible to juice
ingredients with
tough bre?
• Ingredients like celery or ginger contain long bres that may wrap
around the juicing screw and aect the juicer’s performance. When
juicing brous ingredients, do not collect more than 500ml of juice.
After collecting this quantity or less, clean the top-set completely
before juicing again.
Discolouration of the
plastic parts
• After juicing, if the juicer is not cleaned right away, the remaining pulp
inside the top-set can dry up which can make disassembling and
cleaning hard. This can also aect the juicer’s performance and colour.
• Ingredients that are rich in carotenoids such as carrots and spinach
may dye plastic parts. When the parts are dyed with carotenoids,
rub vegetable oil in to the dyed areas and use mild detergent to clean.
• Vegetable oil should only be used during clean-up for parts that are
discoloured. Do not use vegetable oil on the juicing screw or the strainer.
If vegetable oil or oil from animal fat gets on the juicing screw or the
strainer, this can aect the juicer’s performance and may result
in damaged parts.
• The silicone pieces on the top-set can be detached to be
thoroughly cleaned.
Using for purposes
other than juicing
• This juicer is designed to juice ingredients like fruits and vegetables.
• Do not use the juicer for extracting vegetable oil.
• Do not juice ingredients with high contents of vegetable/ animal oil.
• If vegetable/animal oil gets on the juicing screw or the strainer, this can
aect the performance of the juicer and could result in damaged parts.
Troubleshooting

15
EN
2 YEAR LIMITED GUARANTEE
AND 5 YEAR LIMITED MOTOR
GUARANTEE
Sage Appliances guarantees this product for
domestic use in specied territories for 2 years
for all parts of the product and 5 years for the
product’s motor from the date of purchase
against defects caused by faulty workmanship
and materials. During this guarantee period
Sage Appliances will repair, replace, or refund
any defective product (at the sole discretion of
Sage Appliances).
All legal warranty rights under applicable
national legislation will be respected and will
not be impaired by our guarantee. For full terms
and conditions on the guarantee, as well as
instructions on how to make a claim, please visit
www.sageappliances.com.
Guarantee

16
SAGE®
EMPFIEHLT:
SICHERHEIT
GEHT VOR
Wir bei Sage®sind sehr
sicherheitsbewusst.
Beim Design und bei
der Herstellung unserer
Geräte denken wir zu
allererst an Ihre Sicherheit.
Darüber hinaus bitten wir
Sie, bei der Verwendung
jedes Elektrogeräts
angemessene Sorgfalt
anzuwenden und
sich an die folgenden
Vorsichtsmaßnahmen
zu halten.
WICHTIGE
VOR-
SICHTSMASS-
NAHMEN
BITTE ALLE ANWEISUNGEN
VOR DEM GEBRAUCH
LESEN UND ZUR
SPÄTEREN BEZUGNAHME
AUFBEWAHREN.
• Dieses Informationsbuch
steht zum Download unter
www.sageappliances.com
zur Verfügung.
• Vor dem ersten Gebrauch
prüfen, dass Ihre Netzspannung
mit der auf dem Etikett an
der Unterseite des Geräts
übereinstimmt.
• Vor dem ersten Gebrauch
alle Verpackungsmaterialien
abnehmen und sicher
entsorgen.
• Schutzhülle am Netzstecker
sicher entsorgen, da
sie für Kleinkinder eine
Erstickungsgefahr
darstellen könnte.
• Dieses Gerät ist nur für den
Haushaltsgebrauch bestimmt.
Gerät nur bestimmungsgemäß
verwenden.Nicht in fahrenden
Fahrzeugen oder Booten
verwenden.Nicht im Freien
verwenden. Missbrauch kann
Verletzungen nach sich ziehen.
Inhalte
16 Wichtige Vorsichtsmassnahmen
19 Bestandteile
20 Montage
23 Betrieb
24 Pege & Reinigung
26 Fehlerbehebung
30 Garantie

17
DE
• Netzkabel vor dem Gebrauch
vollständig entrollen.
• Gerät in sicherem Abstand
von Kanten auf eine stabile,
hitzebeständige, ebene und
trockene Fläche stellen.
Nicht auf oder neben einer
Wärmequelle wie einem Gas-
oder Elektroherd oder einem
heißen Ofen betreiben.
• Das Gerät kann während
des Betriebs aufgrund von
Vibrationen verrutschen.
• Netzkabel nicht über
Arbeitsplatten oder Tischkanten
hängen lassen, von heißen
Oberächen fern halten,
Kabelgewirr vermeiden.
• Gerät immer AUSschalten,
Netzstecker ziehen und
abkühlen lassen, ehe Sie es
bewegen, reinigen oder lagern.
• Gerät immer ausschalten,
sofern möglich auch an der
Steckdose, und Netzstecker
ziehen, wenn es nicht in
Gebrauch ist.
• Gerät nicht verwenden, wenn
das Netzkabel, der Netzstecker
oder das Gerät selbst in
irgendeiner Weise beschädigt ist.
Wenden Sie sich bei Schäden
und zur Wartung (außer
Reinigung) bitte an den Sage-
Kundendienst oder besuchen
Sie sageappliances.com
• Alle Wartungsarbeiten außer
Reinigung nur von autorisierten
Sage®-Kundendienststellen
vornehmen lassen.
• Kinder nicht mit dem Gerät
spielen lassen.
• Reinigung des Geräts nicht von
Kindern unter 8 Jahren und
nur unter Aufsicht vornehmen
lassen.
• Gerät und Netzkabel für Kinder
bis zu 8 Jahren unzugänglich
aufbewahren.
• Die Installation eines Schutz-
oder Sicherheitsschalters
wird bei der Verwendung von
Elektrogeräten als zusätzliche
Schutzmaßnahme empfohlen.
Es wird ein Sicherheitsschalter
mit maximal 30 mA
Nennleistung empfohlen.
Fachgerechte Beratung
erhalten Sie von Ihrem
Elektriker.
• Gerät nur nutzen, wenn es
richtig zusammengesetzt ist.
Das Gerät funktioniert nur, wenn
es richtig zusammengesetzt ist.
• Gerät nicht auf der
Abtropäche Ihrer
Spüle verwenden.
• Hände, Finger, Haare und
Bekleidung, Schaber und
andere Utensilien während des
Betriebs von beweglichen oder
rotierenden Teilen fern halten.
• Gerät nur bestimmungsgemäß
zur Zubereitung von Speisen
und/oder Getränken
verwenden.

18
• Zur Vermeidung des
Risikos, dass sich das
Gerät aufgrund einer
unbeabsichtigt zurückgesetzten
Überlastsicherung selbst in
Betrieb setzt, keine externen
Schalter (z. B. eine Zeituhr)
anschließen und das Gerät
nicht an einen Stromkreis
anschließen, der das
Gerät regelmäßig aus- und
einschalten kann.
• Alle Anweisungen vor
dem Gebrauch sorgfältig
lesen und zur späteren
Bezugnahme aufbewahren.
• Dieses Gerät kann von
Personen mit eingeschränkten
körperlichen, sensorischen
oder geistigen Fähigkeiten oder
mit mangelnder Erfahrung und
fehlenden Kenntnissen genutzt
werden, sofern sie beaufsichtigt
werden oder in den sicheren
Gebrauch des Geräts
eingewiesen wurden und sich
der entsprechenden Risiken
bewusst sind.
• Gerät nicht von Kindern
bedienen lassen.
• Gerät während des Betriebs
nicht unbeaufsichtigt lassen.
DIESE ANLEITUNG AUFBEWAHREN
• Zutaten nie mit den Fingern
oder anderen Utensilien als
dem mitgelieferten Stopfer in
den Einfüllschacht pressen.
Hand oder Finger nie in den
Einfüllschacht stecken, wenn
dieser am Gerät angebracht ist.
• Steinobst nur entsteint
entsaften.
• Entsafter nie ohne eingesetzten
Trester- und Saftbehälter
verwenden.
• Entsafter nicht verwenden,
wenn die Entsafterschraube
beschädigt ist.
• Gerät nicht länger als 20
Sekunden betreiben, ohne
Zutaten hinzuzufügen.
Dieses Symbol zeigt, dass
das Gerät nicht im
normalen Hausmüll
entsorgt werden sollte.
Es sollte stattdessen bei einem
entsprechenden kommunalen
Wertstohof oder Fachhändler
zur Entsorgung abgegeben
werden.Weitere Einzelheiten
erfahren Sie von Ihrer
Kommunalbehörde.
Zum Schutz gegen
Stromschlag Netzstecker,
Netzkabel oder Gerät nicht in
Wasser oder sonstige
Flüssigkeiten tauchen.

19
DE
Bestandteile
A
Füllkorb Füllschacht
Abnehmbar
B
E
D
G
F
C
H I J K L
A. Füllschacht & Füllkorb Für
unterschiedlich große Stücke
von Obst & Gemüse.
B. Entsafterschale
C. Tresterbehälter
D. Deckelaufsatz
E. Abnehmbares Smart-Cap
F. Saftkrug
G. Motorsockel
H. Rotationswischer
I. Sieb
J. Entsafterschraube
K. Stopfer
L. Reinigungsbürste
Leistungsangaben
220–240V~ 50/60Hz 240W

20
ZUSAMMENFÜGEN
DER OBEREN EINHEIT
Richten Sie die auf jedem der Teile angebrachten
Punkte in der gezeigten Reihenfolge auf
einander aus.Wenn zusammengefügt, drehen
Sie den Deckelaufsatz im Uhrzeigersinn, um ihn
zu schließen.
Montage
VOR DEM ERSTEN GEBRAUCH
Bevor Sie den Entsafter zum ersten Mal
verwenden, entfernen Sie das gesamte
Verpackungsmaterial und alle Werbeaufkleber.
Vergewissern Sie sich, dass der EIN/AUS-
Schalter auf OFF (AUS) steht, dass das Gerät an
der Steckdose ausgeschaltet und der Netzstecker
abgezogen ist.
Waschen Sie die Entsafterschale und das
Entsafterzubehör mit einem weichen Tuch in
warmem Seifenwasser. Spülen und trocknen Sie
alles gründlich.
Wenn Sie Ihr Gerät zum ersten Mal in Betrieb
nehmen, ist es möglich, dass Ihnen einen Geruch
wahrnehmen, der vom Motor kommt. Dies ist
ganz normal und wird sich schnell verziehen.
ZUSAMMENFÜGEN DER OBEREN
EINHEIT MIT DEM MOTORSOCKEL
Stellen Sie den Deckelaufsatz auf die
Entsafterschale. Richten Sie den roten Punkt
auf dem Deckelaufsatz an der ALIGN-Markierung
auf dem Motorsockel und drehen Sie ihn in die
LOCK (GESCHLOSSEN)-Stellung.