Sage Big squeeze sjs700 User manual

the Big Squeeze™

SJS700

EN QUICK GUIDE DE KURZANLEITUNG

SAGE®

RECOMMENDS

SAFETY FIRST

At Sage® we are very safety

conscious. We design and

manufacture consumer

products with the safety of

you, our valued customer,

foremost in mind.

In addition we ask that you

exercise a degree of care

when using any electrical

appliance and adhere to

the following precautions.

IMPORTANT

SAFEGUARDS

READ ALL INSTRUCTIONS

BEFORE USE AND SAVE

FOR FUTURE REFERENCE

• The full information

book is available at

sageappliances.com

• Before using the rst time

ensure your electricity

supply is the same as

shown on the label on the

underside of the appliance.

• Remove and safely discard

any packaging materials

before rst use.

• To eliminate a choking hazard

for young children, safely

discard the protective cover

tted to the power plug.

• This appliance is for

household use only. Do not

use the appliance for anything

other than its intended use.

Do not use in moving vehicles

or boats. Do not use outdoors.

Misuse may cause injury.

• Fully unwind the power cord

before operating.

• Position the appliance on

a stable, heat resistant, level,

dry surface away from the edge

and do not operate on or near

a heat source such as a hot

plate, oven or gas hob.

• Vibration during operation may

cause the appliance to move.

• Do not let the power cord

hang over the edge of a bench

or table, touch hot surfaces

or become knotted.

• Always ensure the appliance

is turned OFF, unplugged

at the power outlet and has

been allowed to cool before

cleaning, attempting to move

or storing.

Contents

2Important safeguards

5Components

6Assembly

9Operation

10 Care & Cleaning

12 Troubleshooting

• Always turn the appliance

to the o position, switch o

at the power outlet and unplug

at the power outlet when the

appliance is not in use.

• Do not use the appliance if the

power cord, plug, or appliance

becomes damaged in any way.

If damaged and maintenance

other than cleaning is

required please contact Sage

Customer Service or go to

sageappliances.com

• Any maintenance other than

cleaning should be performed

by an authorised Sage®

service centre

• Children should not play

with the appliance.

• Cleaning of the appliance

should not be carried out by

children unless they are 8 year

or older and supervised.

• The appliance and its cord

should be kept out of reach

of children aged 8 years

and younger.

• The installation of a residual

current safety switch is

recommended to provide

additional safety when using

all electrical appliances.

Safety switches with a rated

operating current not more

than 30mA are recommended.

Consult an electrician for

professional advice.

• Always ensure the appliance

is properly assembled

before use. The appliance

will not operate unless

properly assembled.

• Do not use the appliance

on a sink drain board.

• Keep hands, ngers, hair,

clothing as well as spatulas

and other utensils away

from moving or rotating

parts during operation.

• Do not use the appliance for

anything other than food and/

or beverage preparation.

• In order to avoid the possible

hazard of the appliance starting

by itself due to inadvertent

resetting of the overload

protection, do not attach

an external switching device

(such as a timer) or connect

the appliance to a circuit

that can regularly switch the

appliance on and o.

• Carefully read all instructions

before operation and save

for future reference.

• The appliance can be used by

persons with reduced physical

or mental capabilities or a lack

of experience and knowledge,

only if they have been given

supervision or instruction

concerning use of the appliance

in a safe way and understand

the hazards involved.

• This appliance shall not be

used by children.

• Do not leave the appliance

unattended when in use.

• Do not push food into the

feed chute with your ngers

or other utensils. Always use

the food pusher provided.

Do not place hand or ngers

into the food chute when it is

attached to the appliance.

• Do not juice stone fruit unless

seeds and/or stones have

been removed.

• Do not operate the juice

extractor without the pulp and

juice container in place.

• Do not use the juice extractor if

the juicing screw is damaged.

• Do not operate the machine

longer than 20 seconds before

inserting ingredients.

SAVE THESE INSTRUCTIONS

The symbol shown

indicates that this

appliance should not be

disposed of in normal

household waste. It should be

taken to a local authority waste

collection centre designated for

this purpose or to a dealer

providing this service. For more

information, please contact your

local council oce.

To protect against electric

shock, do not immerse the

power plug, cord or appliance

in water or any liquid.

Components

Feeding

Basket

Feeding

Tube

Detachable

H I J K L

A. Feeding Tube & Basket

For dierent sizes of produce.

B. Juicing Bowl

C. Pulp Cup

D. Drum Lid

E. Detachable Smart Cap

F. Juice Jug

G. Motor Body

H. Rotation Wiper

I. Strainer

J. Juicing Screw

K. Pusher

L. Cleaning Brush

Rating Information

220–240V~ 50/60Hz 240W

TOP SET ASSEMBLY

Align the dots on each part and assemble

in the order shown. Once assembled, turn the

drum lid clockwise to close.

Assembly

BEFORE FIRST USE

Before using your Juicer for the rst time, remove

any packaging material and promotional labels.

Ensure the power is in the OFF position, the juicer

is switched o at the power outlet and the power

cord is unplugged.

Wash bowl and juicing tools in warm soapy water

with a soft cloth. Rinse and dry thoroughly.

When rst using your appliance, you may notice

an odour coming from the motor. This is normal

and will dissipate with use.

TOP-SET AND BODY ASSEMBLY

Place the drum lid on the juicing bowl. Align the

red dot on the drum lid with the ALIGN mark

on the body and turn to the LOCK position.

ASSEMBLY

1. Firmly insert the compression silicone into

the slot below the pulp spout.The Juicer

may leak if not assembled properly.

2. Assemble the strainer into the rotation

wiper then place this assembly in to the

juicing bowl ensuring the red dot on the

strainer is aligned with the red dot on the

juicing bowl.

3. Place the juicing screw into the strainer.Turn

and press down on it until it clicks into place.

The juicing screw needs to be locked in place

in order to close the drum lid.

4. Place the drum lid on to the juicing bowl

aligning the dot on the drum lid with the

red dot on the juicing bowl.

TIP

For easy assembly hold the drum lid by grabbing

the feeding tube and turn clockwise as shown

in the illustration.

5. Align the red dot on the drum lid with the

ALIGN mark on the body and turn to the

CLOSE position.

6. Align arrows on drum lid and motor body.

NOTE

The juicer will not operate if the down arrow

on the drum lid is not completely aligned with

the CLOSE mark on the body.

7. Place the pulp cup under the pulp spout and

place the juice cup under the juice spout

as shown in the illustration.

Detachable

Operation

USING YOUR JUICER

1. After preparing the ingredients, plug the

power cord into a wall outlet. Do not touch

the power cord with wet hands. It may cause

electrical shock, short-circuit, or re.

2. Press the FORWARD button to operate.



Forward: Pulls down and slowly masticates

the ingredients.

Reverse: Pushes the ingredients back up

to dislodge them.The REVERSE button

only works while holding down the switch.

3. Insert the prepared ingredients into the

feeding tube, one piece at a time. If large

quantity of ingredients are put into the

feeding tube, it can cause the juicer to stop

Remove hard seeds or pits in fruits.

When juicing frozen fruits, completely

thaw before juicing.

HARD VEGETABLES & HIGH FIBRE

FOODS (E.G. CARROTS, BEETROOT,

& SPINACH)

Insert into the feeding tube.

Tough and brous ingredients: Cut to 2cm

wide and 5cm long.

Fibrous leafy vegetables: (celery, kale, collard

greens, etc.): Cut the stems into 5cm long and

bundle up the leafy part as you insert them into

the juicer.

SOFT FRUITS & VEGETABLES

(E.G. APPLES, ORANGES & TOMATOES)

Insert into the feeding basket.

Soft ingredients: Cut ingredients into 1–4

pieces. Insert the prepared ingredients into the

feeding basket and push down the ingredient

with the basket lid to extract.

Care & Cleaning

4. Remove the juicing screw, strainer and

rotation wiper unit from the juicing bowl.

Clean with provided brush.

NOTE

Immediately clean the juicer after each use.

If remaining residue in the juicer dries up,

it can make disassembling and clean-up dicult.

The excess build up can cause poor performance

in future uses. For easier disassembly, place the

top-set in the sink and run the water through from

the top of the top-set.

We do not recommend to wash any parts of the

juicer in the dishwasher. Washing parts in the

dishwasher can cause damage to them due

to prolonged exposure to harsh detergents,

hot water and pressure.

5. Place the juicing bowl under running water

and unplug the compression silicone to clean

the pulp spout.

Extract all the remaining pulp in the juicing bowl

before stopping the juicer.

For easier clean up, operate the juicer for

an additional 30 seconds after the juice is

extracted. Then ll the juicing bowl with water

and run the juicer before opening the drum lid.

When the drum lid is stuck, press the

REVERSE – OFF – FORWARD button in this

order, switching back and forth 2 to 3 times to

dislodge.Then place both hands on the drum

lid and rmly press down while simultaneously

turning the drum lid to open.

CLEANING THE JUICER

1. Switch OFF and unplug the power cord

from the wall outlet.

2. Turn the drum lid counter clockwise to open.

WARNING

When moving the appliance, do not lift by

grabbing the feeding tube. Always lift the

appliance by grabbing the body or handle.

3. Turn the top-set counter clockwise and lift

o the body.

6. Under running water, clean the outside of the

juicing screw with a dish scrub. Use the tip of

the cleaning brush to push out any residue in

the crevices on the bottom of the juicing screw.

Thoroughly clean the juicing screw ensuring that

the juicing screw is clean without any residue.

Thoroughly dry the bottom of the juicing screw.

After juicing ingredients with seeds, make

sure to thoroughly clean the bottom crevice

of the juicing screw. (If this area isn’t properly

cleaned, it can cause the part to be damaged).

7. Clean the body with a soft damp towel and dry.

If the towel is dripping wet, make sure to

squeeze out the excess liquid before using

it on the juicer.

CLEANING SILICONE PARTS

Clean the rotation wiper under running water.

Thoroughly dry after cleaning. Before assembling

the top-set, ensure that the compression silicone

and silicone ring are rmly inserted.

If the compression silicone and silicone ring

are not rmly inserted, juice may leak from the

bottom of the juicing bowl.

COMPRESSION SILICONE

Unplug to clean.

After cleaning, rmly insert into the slot below

the pulp spout.

SILICONE RING

Remove the silicone ring from the juicing

bowl to clean.

After cleaning, push in the silicone ring with the

smaller surface facing down.

SMART CAP

Remove from the juice spout to clean.

After cleaning, attach the smart cap to the

smart cap silicone on the juice spout.

Troubleshooting

PROBLEM EASY SOLUTION

There is no power to

the juicer

• Check if the power cord is properly plugged in.

• Check if the drum lid and the juicing bowl are properly assembled.

• Check if the top-set and the body are properly assembled.

NOTE: Juicer will not operate if parts are not assembled properly.

Low juice yield • Dierent ingredients hold dierent amounts of uid that will yield dierent

amounts of juice.

• If the ingredients are not fresh, they may contain reduced amount of uid,

which will yield less juice. Soak ingredients in cold water for about

30 minutes prior to juicing for the best result.

• Check if the compression silicone is rmly inserted.

• If the ingredient itself has low water content, it may help to soak it in water

before juicing.

• If juicing ingredients with small seeds, after a few servings, it may reduce

the juice yield. For best result, disassemble and wash the top set in

between juicing.

• If there is seed residue on the bottom of the strainer, this can aect juicer

performance and the overall juice yield.

There is too much

pulp in the juice

• To reduce the ne pulp, clean the top-set frequently and extract the pulp.

• Use a mesh strainer and put the juice through it to collect the

unwanted pulp.

• If the strainer and the screw are damaged and aecting the juicer’s

performance, it is recommended the parts be replaced.

• The lifetime of each part may vary depending on length and method of use

and ingredients extracted.

The drum lid will not

• Make sure the juicing screw is pushed all the way in to the strainer in order

for the drum lid to close properly.

• If the juicing screw is not properly in position, the drum lid may not close.

PROBLEM EASY SOLUTION

Odd noise from the

juicer

• Check if the parts are assembled correctly.Try reassembling the parts

and listen for the odd noise.

• Do not start the juicer unless there are ingredients and/or liquid in it.

• Operating the juicer without ingredients can cause damage to the screw.

• If the juicer is operated without ingredients or liquid, the noise level can

increase and also can lead to damage.

• The friction noise from the juicing screw and the strainer will disappear

when ingredients are inserted into the juicer.

• If the noise occurs when ingredients are inserted into the juicer, check

the size of the ingredients. Do not insert anything over 3cm in thickness.

• Depending on the type of ingredients, the dimensions can be smaller.

• The noise can occur if the juicer is operated on an uneven or slanted

surface. Place the juicer on a horizontally at surface when operating.

The extracted pulp is

very moist

• During the very beginning of extraction, the pulp can be more moist.

• Depending on the ingredient’s condition, the extracted pulp can be

aected; especially when the ingredient is not fresh, the juice can be

extracted with the pulp.

During operation, the

juicing bowl shakes

• The juicing screw and the strainer are set up to crush and squeeze the

ingredients. It is normal for the juicing screw and the strainer to vibrate.

• If the ingredient contains strong bre, the vibration from the top-set

may be stronger.

During juicing, the

juicer stopped

• Check the power cord and make sure it is plugged in correctly.

• Check that all the parts are correctly assembled.

• If too many ingredients are inserted at one time, this can cause the juicer

to stop.

• When the juicer stops because there are too many ingredients inserted in

it, press the REVERSE – OFF – FORWARD button in this order, switching

back and forth 2 to 3 times.The reverse setting will push the ingredients up

and the forward setting will pull the ingredients down.

• After using more than 30 minutes, if the juicer stops due to the overload

protection, let the juicer cool for 30 minutes to 1 hour before juicing again.

• If there are hard seeds within the ingredients, remove them before juicing.

Hard seeds can damage the juicer.

Layers of separation

in the juice

• Depending on the density of the ingredients, the extracted juice may show

layers of dierent juices. It is dierent from separation due to oxidation

caused by juicing with a high-speed juicer.

PROBLEM EASY SOLUTION

The drum lid is stuck • After juicing, let the juicer operate for another 30 seconds to extract

the remaining pulp.

• If there is too much pulp in the top-set, this can cause the drum lid to

not open. In this situation, press the REVERSE – OFF – FORWARD

button in the order, switching back and forth 2 to 3 times.Then

place both hands on the drum lid and rmly press down while

simultaneously turning the drum lid to open.

• Pour water down the feeding tube to rinse out the insides and then try

opening the drum lid.

Juice dripping down

the body

• If the compression silicone on the bottom of the juicing bowl is not

plugged in correctly, the juice may seep out on to the juicer body.

Before assembling the parts, check and make sure the compression

silicone is plugged in correctly.

Is it possible to juice

ingredients with

tough bre?

• Ingredients like celery or ginger contain long bres that may wrap

around the juicing screw and aect the juicer’s performance. When

juicing brous ingredients, do not collect more than 500ml of juice.

After collecting this quantity or less, clean the top-set completely

before juicing again.

Discolouration of the

plastic parts

• After juicing, if the juicer is not cleaned right away, the remaining pulp

inside the top-set can dry up which can make disassembling and

cleaning hard. This can also aect the juicer’s performance and colour.

• Ingredients that are rich in carotenoids such as carrots and spinach

may dye plastic parts. When the parts are dyed with carotenoids,

rub vegetable oil in to the dyed areas and use mild detergent to clean.

• Vegetable oil should only be used during clean-up for parts that are

discoloured. Do not use vegetable oil on the juicing screw or the strainer.

If vegetable oil or oil from animal fat gets on the juicing screw or the

strainer, this can aect the juicer’s performance and may result

in damaged parts.

• The silicone pieces on the top-set can be detached to be

thoroughly cleaned.

Using for purposes

other than juicing

• This juicer is designed to juice ingredients like fruits and vegetables.

• Do not use the juicer for extracting vegetable oil.

• Do not juice ingredients with high contents of vegetable/ animal oil.

• If vegetable/animal oil gets on the juicing screw or the strainer, this can

aect the performance of the juicer and could result in damaged parts.

Troubleshooting

Notes

SAGE®

EMPFIEHLT:

SICHERHEIT

GEHT VOR

Wir bei Sage®sind sehr

sicherheitsbewusst.

Beim Design und bei

der Herstellung unserer

Geräte denken wir zu

allererst an Ihre Sicherheit.

Darüber hinaus bitten wir

Sie, bei der Verwendung

jedes Elektrogeräts

angemessene Sorgfalt

anzuwenden und

sich an die folgenden

Vorsichtsmaßnahmen

zu halten.

WICHTIGE

SICHERHEITS-

HINWEISE

BITTE ALLE ANWEISUNGEN

VOR DEM GEBRAUCH

LESEN UND ZUR

SPÄTEREN BEZUGNAHME

AUFBEWAHREN.

• Die komplette

Informationsbroschüre ist

unter sageappliances.com

verfügbar.

• Vor dem ersten Gebrauch

prüfen, dass Ihre

Netzspannung mit der auf

dem Etikett an der Unterseite

des Geräts übereinstimmt.

• Vor dem ersten Gebrauch

alle Verpackungsmaterialien

abnehmen und sicher

entsorgen.

• Schutzhülle am Netzstecker

sicher entsorgen, da

sie für Kleinkinder eine

Erstickungsgefahr

darstellen könnte.

• Dieses Gerät ist nur für den

Haushaltsgebrauch bestimmt.

Gerät nur bestimmungsgemäß

verwenden. Nicht in fahrenden

Fahrzeugen oder Booten

verwenden. Nicht im Freien

verwenden. Missbrauch

kann Verletzungen nach

sich ziehen.

• Netzkabel vor dem Gebrauch

vollständig entrollen.

Inhalt

16 Wichtige Sicherheitshinweise

19 Bestandteile

20 Montage

23 Betrieb

24 Pege & Reinigung

26 Fehlerbehebung

• Gerät in sicherem Abstand

von Kanten auf eine stabile,

hitzebeständige, ebene und

trockene Fläche stellen.

Nicht auf oder neben einer

Wärmequelle wie einem Gas-

oder Elektroherd oder einem

heißen Ofen betreiben.

• Das Gerät kann während

des Betriebs aufgrund von

Vibrationen verrutschen.

• Netzkabel nicht über

Arbeitsplatten oder

Tischkanten hängen lassen,

von heißen Oberächen fern

halten, Kabelgewirr vermeiden.

• Gerät immer AUSschalten,

Netzstecker ziehen und

abkühlen lassen, ehe Sie es

bewegen, reinigen oder lagern.

• Gerät immer ausschalten,

sofern möglich auch an der

Steckdose, und Netzstecker

ziehen, wenn es nicht in

Gebrauch ist.

• Gerät nicht verwenden,

wenn das Netzkabel, der

Netzstecker oder das Gerät

selbst in irgendeiner Weise

beschädigt ist. Wenden

Sie sich bei Schäden

und zur Wartung (außer

Reinigung) bitte an den Sage-

Kundendienst oder besuchen

Sie sageappliances.com

• Alle Wartungsarbeiten außer

Reinigung nur von autorisierten

Sage®-Kundendienststellen

vornehmen lassen.

• Kinder nicht mit dem Gerät

spielen lassen.

• Reinigung des Geräts nicht

von Kindern unter 8 Jahren

und nur unter Aufsicht

vornehmen lassen.

• Gerät und Netzkabel für

Kinder bis zu 8 Jahren

unzugänglich aufbewahren.

• Die Installation eines Schutz-

oder Sicherheitsschalters

wird bei der Verwendung

von Elektrogeräten als

zusätzliche Schutzmaßnahme

Popular Juicer manuals by other brands

Sytech

Sytech SY-EX05 user manual

Maxwell

Maxwell MW-1101 Manual instruction

Philips

Philips Avance Collection HR1932 Series user manual

Panasonic

Panasonic MJ-CB600 operating instructions

Dahlert

Dahlert DT-SJ-19 instruction manual

ElectrIQ

ElectrIQ WF1000 user manual

amzchef

amzchef ZM1507 instruction manual

Philips

Philips HR1858/50 manual

Clatronic

Clatronic ZP 3066 Instruction manual & guarantee

Tribest

Tribest Solostar 4 SS-4200 Operation manual

ARESA

ARESA AR-2502 instruction manual

Fritel

Fritel JP 9970 manual

ARDESTO

ARDESTO CJK-1L instruction manual

Rohnson

Rohnson R-412 instruction manual

Stollar

Stollar The Juice Presso BJP500 Instruction booklet

Trebs

Trebs 99327 manual

Shine KITCHEN

Shine KITCHEN SJX-1WH Operation manual

Wolfgang Puck

Wolfgang Puck SWPCJ0040 Use and care

Sage Big Squeeze SJS700 User manual

Popular Juicer manuals by other brands