Samcon ExCam IPM1145 User manual

ExCam IPM1145-(L)
User manual

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 2 of 40
Content
1Introduction ..............................................................................................................5
2Technical Data..........................................................................................................6
2.1 Parameters of the explosion protection...............................................................6
2.2 Electrical parameters of the camera module.......................................................7
2.2.1 ExCam IPM1145-(L) (PoE+) (Camera and Heater) ..................................................................7
2.2.2 ExCam IPM1145........................................................................................................................7
2.2.3 ExCam IPM1145-L ....................................................................................................................7
2.3 Electrical parameters of the PTC heat load circuit (optional)...............................8
2.4 Connection cable SKD02-T.................................................................................8
2.5 Power Supply cable (optional)...........................................................................10
2.6 Technical specification of the camera modules.................................................11
2.6.1 Axis M1145..............................................................................................................................11
2.6.2 Axis M1145-L...........................................................................................................................11
2.7 IR-LED Illumination ...........................................................................................12
2.7.1 Axis M1145..............................................................................................................................12
2.7.2 Axis M1145-L...........................................................................................................................12
2.8 Temperature range (MTBF) ..............................................................................13
2.8.1 ExCam IPM1145(-L) PoE+......................................................................................................13
2.8.2 ExCam IPM1145......................................................................................................................13
2.8.3 ExCam IPM1145-L ..................................................................................................................13
2.9 Other technical data..........................................................................................13
3Safety guidelines....................................................................................................16
4Illustration of the model key..................................................................................17
5Commissioning ......................................................................................................19
5.1 Step 1: Installation.............................................................................................19
5.2 Step 2: Electrical connection.............................................................................19
5.2.1 Potential equalization...............................................................................................................20
5.2.2 Connection and protection.......................................................................................................21
5.2.3 Tests prior to switching on voltage ..........................................................................................25
5.3 Testing of the status LED..................................................................................25
5.4 Step 3: Adjusting the lens..................................................................................26
5.4.1 Work preparation .....................................................................................................................28
5.4.2 Opening the pressure-resistant housing..................................................................................28
5.4.3 Extracting/inserting an SD storage card..................................................................................32
5.4.4 Hardware Reset.......................................................................................................................33
5.4.5 Closing of the pressure-resistant housing ...............................................................................33
6Network access and visualization ........................................................................35
6.1 Browser Support................................................................................................35
6.2 Assigning the IP address...................................................................................36
6.3 Password / identification....................................................................................37
7Maintenance / Servicing / Alterations...................................................................38
8Repairs and Maintenance......................................................................................38
9Disposal / Recycling ..............................................................................................38
10 Drawings..............................................................................................................38
11 Notes....................................................................................................................39

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 3 of 40
Table of Figures
Figure 1.1 –ExCam IPM1145-L with wall mount bracket and roof....................................5
Figure 2.1 –ExCam IPM1145-L......................................................................................12
Table 4.1 –Model key.....................................................................................................17
Figure 5.1 –ExCam IPM1145-(L) potential equalization .................................................20
Table 5.1 –Potential equilization.....................................................................................20
Figure 5.2 –Cable glands and supply cable....................................................................21
Figure 5.3 –ExCam IPM1145-(L) T08-VA2.1.K1.BOR-C-XXX-K-X................................21
Figure 5.4 –ExCam IPM1145-(L) T08-VA2.1.K1.BOR-C-XXX-P-X ................................22
Figure 5.5 –ExCam IPM1145-(L) T08-VA2.1.K1.BOR-C-XXX-X-L(L)............................22
Table 5.2 –Pin assignment SKD02-T and plug contact RJ45.........................................23
Figure 5.6 –RJ45 Contact assignment ...........................................................................23
Figure 5.7 –SKD02-T Pin assignment ............................................................................24
Table 5.3 –Pin assignment supply cable for heating type L............................................24
Table 5.4 –Pin assigment supply cable for cooling type H .............................................25
Table 5.5 –Status and control LED.................................................................................26
Figure 5.8 –Remote Zoom control of the ExCam IPM1145-L.........................................26
Figure 5.9 –Live View with IR control of the ExCam IPM1145-L ....................................27
Table 5.6 –Lens data......................................................................................................27
Figure 5.10 –Removing the protection roof (1/2)............................................................29
Figure 5.11 –Removing the protection roof (2/2)............................................................29
Figure 5.12 –Opening the ExCam IPxxx ........................................................................30
Figure 5.13 –ExCam IPM1145-L installation components..............................................31
Figure 5.14 –MicroSD card slot......................................................................................32
Figure 6.1 –Axis IP Utility................................................................................................36

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 4 of 40
Revision history
Product: T08 ExCam® IPM1145-(L)
Title: Betriebsanleitung der ExCam®IPM1145-(L)
Doc.-Id.: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02
Author: Thiemo Gruber
Date: September 03, 2015
Last revision: November 06th, 2018
Rev.-
Index
Date
Name
Remarks
Authorization of the
EX Supervisor
0
Sep 03, 2015
T. Gruber
Compilation of the document
1
Apr 13, 2016
T. Gruber
Revisions: Termination of ExCam
IPM1144-L, Deletion of the document
overview
2
Nov. 06th 2018
S.Seibert
Adding the PoE+ Versions

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 5 of 40
1 Introduction
The ExCam IPM1145-(L) is a high-performance digital camera system (type T 08), manu-
factured by SAMCON Prozessleittechnik GmbH. The system is intended for network
transmission via IP/ TCP/ RTSP protocols and Web Interface access. The explosion-
proof device is very compact in design, covers all relevant features of a professional
CCTV surveillance camera and is available as ExCam IPM1145 or ExCam IPM1145-L.
Via the data cable, the camera systems are also supplied with power via Power-over-
Ethernet (PoE IEEE802.3af/at) so that ideally only one connection cable is required.
The high-performance of the ExCam IPM1145-(L) regarding its usage for industrial pro-
cess, plant, or person surveillance is based on a high-resolution output (1080p) to
achieve a detailed and high contrast picture quality even at difficult light settings,
day/night functionality, edge storage, individually configurable H.264 and Motion JPEG
video streams, an intelligent and fast P-Iris aperture control as well as optional I/O inter-
faces. The highly efficient infrared LEDs of the ExCam IPM1145-L are adjustable to meet
the individual application requirements to allow a surveillance of objects also in complete
darkness.
The camera system is suitable for indoor as well as outdoor applications preferably within
hazardous areas of the chemical and/or petro-chemical industry, at offshore plants, in
mines, and at biogas plants. The Ex d stainless steel housing allows additional alloys, a
powder coating, or coats of varnishes as well as various mechanical accessories in order
to extend the resistance towards extreme environmental conditions (salt water, acid, so-
lar radiation, high mechanical strains etc.). Due to the usage of high-quality PTFE seal-
ings, not only the protection level IP68 is reached but also the chemical resistance is
maximized.
Figure 1.1 –ExCam IPM1145-L with wall mount bracket and roof

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 6 of 40
2 Technical Data
2.1 Parameters of the explosion protection
Identification marks according to
Directive 94/9/EG (until April 20, 2016):
Directive 2014/34/EU: II 2G (zone 1 and 2)
II 2D (zone 21 and 22)
I M2
Explosion protection (gas): Ex d IIC T6 Gb or
Ex d IIC T5 Gb or
Ex d IIB T6 Gb or
Ex d IIB T5 Gb
Explosion protection (dust): Ex tb IIIC T80°C Db IP68 or
Ex tb IIIC T95°C Db IP68 or
Ex tb IIIB T80°C Db IP68 or
Ex tb IIIB T95°C Db IP68
Explosion protection (mining) Ex d I Mb
Protection level: IP 68 (IEC /EN 60529)
Transportation and storage
ambient temperature (EX)
1
ExCam IPM1145: -60°C to +65°C (temperature class T6)
-60°C to +70°C (temperature class T5)
ExCam IPM1145-L: -60°C to +60°C (temperature class T6)
-60°C to +65°C (temperature class T5)
Nominated body: TÜV Rheinland (number 0035)
EC Type Examination: TÜV 14 ATEX 7539 X_1st supplement
IECEx TUR 14.0026X_issue No.1
Additional certificates: EAC-Ex TC_RU_C_DE.MIO62.B.01921
Test protocol ATEX: 557/Ex.539.01/14
Test report IECEx: DE/TUR/ExTR14.0026/01
Quality Assessment Report: DE/BVS/QAR14.0006/00
1
Maximum ambient temperature range relevant for explosion protection might deviate to the maximum functional temperature range.
For maximum functional temperature range (MTBF) see chapter 3.12

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 7 of 40
Product compliance
Gas explosion protection: - IEC 60079-0:2011, EN 60079-0:2012
- IEC 60079-1:2007, EN 60079-1:2008
- IEC 60079-11:2011, EN 60079-11:2012
- IEC 60079-18:2009, EN 60079-18:2009
- IEC 60079-28:2006/ ISH1:2014,
EN 60079-28:2007 (Beiblatt 1:2014-09)
- GOST R IEC 60079-0:2011
- GOST IEC 60079-1:2011
Dust explosion protection: - IEC 60079-31:2008, EN 60079-31:2009
- GOST R IEC 60079-31:2010
Others: - IEC 60079-14:2013, EN 60079-14:2014
- DIN 7080:2005-05
- IEC 60529:1989 + A1:1999,
DIN EN 60529:1991 + A1:2000
- DIN VDE 0118-1:2010-02
2.2 Electrical parameters of the camera module
2.2.1 ExCam IPM1145-(L) (PoE+) (Camera and Heater)
Power supply: PoE, IEEE 802.3at type 2 class 4
Reference power: 48 V DC (44...54 V DC)
Maximum power input: 24.9 W (30 W from the PSD)
2.2.2 ExCam IPM1145
Power supply: PoE, IEEE 802.3af/ 802.3at type 1 class 2
Reference power: 48 V DC (44...54 V DC)
Maximum power input: 6.0 W
2.2.3 ExCam IPM1145-L
Power supply: PoE, IEEE 802.3af/ 802.3at type 1 class 3
Reference power: 48 V DC (44...54 V DC)
Maximum power input: 10.5 W

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 8 of 40
2.3 Electrical parameters of the PTC heat load circuit (optional)
Reference power UN: 24 V DC
Nominal voltage PN: 20 W at type L (TAMB ≥-30°C)
40 W at type LL (TAMB ≥-60°C)
Attention!
The power consumption of the housing heating is determined by the ambient tempera-
ture or, respectively, by the PTC features
2
found in the modules’ individual operating
points. In addition, the performance of the PTC load circuit is influenced by the switching-
on characteristics of the CB06 circuit board, the load operation of the internal camera
module as well as the convection cooling on the outside (heat dissipation via housing).
Per module, the switch-on power can reach Pmax > 100W! Supply cable fine wire fuses
have to be dimensioned accordingly by the end user. A super-slow (-TT-) trigger charac-
teristic is recommended.
The typical continuous power rating at the low temperature range (TAMB -30°C) is
P(-30°C) = 12.2 W at a saturated condition
The typical continuous power rating at the artic temperature range (TAMB -60°C) is
P(-60°C) = 26.8 W at a saturated condition
The typical start-up peak at the low temperature range (1x HP05 heating element) is
Imax > 4000mA !
The typical start-up peak at the artic temperature range (2x HP05 heating element) is
Imax > 8000mA !
The typical in-rush-duration for IPTC < 1000mA per module is tON ≤45s
The typical in-rush-duration for IPTC < 500mA per module is tON ≤120s
(saturated range/ steady current)
2.4 Connection cable SKD02-T
Description: Samcon System Cable Digital (type „SKD02-T“)
for low temperature ranges, data transfer and
power supply of the camera modules M1145
and M1145-L (DIN EN 60079-14: 2014 con-
form)
Sheath color: Yellow-green (GN), similar RAL6018
Ex d marshalling: via the cable gland 1
3
located on the right
(according to DIN EN 60079-14:2014
[chapter 10.6.2])
2
PHP05 = KxAxT (K=5.5W/m2)
3
According to the current standard DIN EN 60079-14:2014, the dimensioning/execution of the cable gland with or without integrated
pressure barrier / compound grouting does not depend anymore on the marked gas explosion group (IIB, IIC) or the Ex d pressure
chamber volume (<2000cm3, ≥2000cm3) but solely on the length of the suitable connection cable (<3m, ≥3m)

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 9 of 40
At a cable connection length of ≥3 m:
(without integrated pressure barrier/ with
elastomer sealing on the outer sheath) e.g.:
„ADE 4F MsNi Type5 - M20x1.5 (CAPRI)“,
with additional strain relief;
At a connection cable length of < 3m:
(with integrated pressure barrier / epoxide
compound grouting of the single conductors
and duroplast/elastomer sealing of the outer
sheath) e.g.: „8163/2 PXSS2K - M20x1.5 (R.
Stahl GmbH)“
Outer diameter: 9.0 ± 0.2mm
Wall thickness: 0.9 ± 0.1mm
Bending radius: 10 x outer diameter at installation
5 x outer diameter after installation
Tensile: Max. 140N
Temperature range: -10° C to +50° C (at point of installation)
-60° C to +80° C (fixed installed)
Conductor design: 4 x 2 x AWG22/1 blank, CAT.6a
Isolation: SFS-PE foamed
Core diameter: 1.52 ± 0.02 mm
Color code: IEC 708-1
Pair shielding: Compound aluminum foil
Shielding: Copper braid, multiple wires 0-10 vz, opt. cov-
erage approx. 85%
Outer sheath: PUR FHF
Characteristics: PUR halogen free, flame resistant (EN 60332-
1-2), UV and ozone resistant, high chemical re-
sistance, EMV shielded
(q.v. www.samcon.eu, data sheet SKD02-T)
User interface: P(Plug) version: RJ-45 Stecker (EIA/TIA-
568B), e.g. Weidmüller IE-PS-RJ45-FH-BK,
Phoenix Contact VS-08-RJ45-5-Q/IP20 etc.,
10BASE-T/100BASE-TX PoE
K(terminal block) version: about 12 cm stripped:
8 x single conductors twisted pair (solid conduc-
tor A=0.33mm2, ø=0.64 mm approx. 6 mm
stripped), 1 x shield (Cu braid tinned 1.5 mm2,
ferule color code according to DIN 46228)
10BASE-T/ 100BASE-TX PoE

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 10 of 40
2.5 Power Supply cable (optional)
Description: Ölflex® 440P
4
(U.I. Lapp GmbH), power supply
for the PTC heat load circuit as well as for the
electronical regulation of the CB06 for T08 Ex-
Cam with the model key „L“ and „LL“,
(DIN EN 60079-14: 2014 conform)
Sheath color: Silver grey (GY) matt, similar RAL7001
Ex d marshalling: via cable gland 2
5
located on the left (according
to DIN EN 60079-14:2014 [Chapter 10.6.2])
At a cable connection length of ≥3 m:
(without integrated pressure barrier/ with
elastomer sealing on the outer sheath) e.g.:
„ADE 4F MsNi Type5 - M20x1.5 (CAPRI)“,
with additional strain relief;
At a connection cable length of < 3m:
(with integrated pressure barrier / epoxide
compound grouting of the single conductors
and duroplast/elastomer sealing of the outer
sheath) e.g.:
„8163/2 PXSS2K - M20x1.5 (R. Stahl GmbH)“
Outer diameter: 7.5 mm
Outer sheath: Polyurethane mixture TMPU according to EN
50363-10-2 / VDE 0207-363-10-2
Bending radius: 12.5 x outer diameter (occasional movement)
4.0 x outer diameter (fixed installation)
Conductor design: 3G1.5 (0012838), 3 x 1.5 mm2(ø=1.4 mm),
Fine wired tinned copper strand according to.
IEC 60228 / VDE 0295, class 5, with protective
earth (GN/YE)
Copper index: 43.0 kg/km
Weight: 96.0 kg/km
Tensile strength: 15 N/mm2
Characteristics: Resistant to oil and drilling fluids according to
IEC 61892-4: supplement D, wear and notching
resistant, halogen free (VDE 0472-815) and
flame-retardant according to IEC 60332-1-2, re-
sistant to hydrolysis and microbes, UV re-
sistant, additional testing requirements accord-
ing to IEC 60811, EN 50396 and EN 50396
4
Further cables available upon request, e.g. „Ölflex® Petro FD 865 CP“ (high resistance against oil and drilling liquids) or „XPLE
Armoured 3 x 2.5“ (extremely robust, particularly designed for offshore environments)
5
According to the current standard DIN EN 60079-14:2014, the dimensioning/execution of the cable gland with or without integrated
pressure barrier / compound grouting does not depend anymore on the marked gas explosion group (IIB, IIC) or the Ex d pressure
chamber volume (<2000cm3, ≥2000cm3) but solely on the length of the suitable connection cable (<3m, ≥3m)

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 11 of 40
(q.v. www.samcon.eu, data sheet Ölflex 440P)
Conductor identification code: Black conductors with white numbers with
GN/YE- protective earth according to DIN EN
50334 / VDE 0293-334
Classification: ETIM 5.0 Class-ID: EC 000104, ETIM 5.0 type:
Control cable
Conductor insulation: Thermal Plastic Elastomer (TPE)
Nominal current U0/U: 300/500 V AC/DC
Test voltage: 3000 V
Temperature range: -40°C to +90°C (occasional movement)
-50°C to +90°C (fixed installation)
User interface: P(Plug) version: n/a / upon request
K(terminal block) version: 3x 1.5 mm2(3G1.5)
Cu strand with ferules (color code according to
DIN 46228). Sheath about 12 cm stripped and
furnished with bend relief / shrink tubing
2.6 Technical specification of the camera modules
Note:
Technical details of the internal CCTV module such as light sensitivity, resolution, frame
rate sensor, shutter times, lens details, streaming functions, supported network protocols,
event trigger, storage options, and picture parameter setting via the web interface are
thoroughly provided in the data sheets of the camera manufacturer and not part of the
T08 ExCam user manual.
2.6.1 Axis M1145
Data sheet:
http://www.axis.com/files/datasheet/ds_M1145_1480602_en_1604.pdf
User manual:
http://www.axis.com/files/manuals/um_m1145_57266_en_1512.pdf
2.6.2 Axis M1145-L
Data sheet:
http://www.axis.com/files/datasheet/ds_m1145l_1480603_en_1506.pdf
User manual:
http://www.axis.com/files/manuals/um_m1145l_57268_en_1512.pdf

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 12 of 40
2.7 IR-LED Illumination
2.7.1 Axis M1145
Specification: n/a
(the Axis M1145 camera module does not have
integrated IR LED illumination with additional
photo diode for measuring the light conditions)
2.7.2 Axis M1145-L
Specification: 2 x highly efficient LEDs
6
- with optimized infrared spectral components
(λcentroid = 850 [nm]), allows high-contrast
black and white pictures in darkness and un-
der difficult light conditions
- Adjustable intensity and illumination angle,
typical range up to 15 m
- Light sensor for automatic activation or deac-
tivation of the infrared diodes
- Includes a particularly developed chloroprene
rubber adapter for limiting the scattering an-
gle due to infrared light reflections within the
pressure resistant housing (q.v. optimization
of shadowing and interferences due to multi-
ple LED light reflections at the borosilicate
sight glass of the stainless steel housing)
- Radiation angle: Max 30°
Figure 2.1 –ExCam IPM1145-L
6
Depending on the adjusted illumination angle, it is possible that at turned on IR LED illumination, the angle of view is slightly restrict-
ed or a minor shadowing is noticeable

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 13 of 40
2.8 Temperature range (MTBF)
2.8.1 ExCam IPM1145(-L) PoE+
Permitted functional ambient temperature (MTBF)
7
: -30°C to +40°C (type L)
2.8.2 ExCam IPM1145
Permitted functional ambient temperature (MTBF): 0°C to +40°C (type N)
0°C to +70°C (type H) (T5)
-30°C to +40°C (type L)
-60°C to +40°C (type LL)
-30°C to +70°C (type LH) (T5)
2.8.3 ExCam IPM1145-L
Permitted functional ambient temperature (MTBF): 0°C to +40°C (type N)
0°C to +65°C (type H) (T5)
-30°C to +40°C (type L)
-60°C to +40°C (type LL)
-30°C to +65°C (type LH) (T5)
2.9 Other technical data
Protection level EN 60529/ IEC 529: IP68
Test conditions (>IP67): 24h/ 3m water column,
pH-neutrality, temperature of the liquid medium:
+5° C ≤ TWater ≤ +20° C.
An additional mechanical protection against wa-
ter jets is recommended
Housing material
8
of the pressure resistant enclosure (DIN EN 60079-1: 2008) according
to DIN EN 10027-2: 2015-07 (making system for steel):
Housing material (standard)MNo.: 1.4404 (X2CrNiMo17-12-2),
AISI 316L / V4A
7
Functional temperature range concerning the operational temperature range of the installed non-Ex components according to AXIS
manufacture declarations (MTBF –mean time between failures) under consideration of thermal power loss and the temperature coef-
ficient of the Ex d housing. The functional temperature ranges always lay within the explosion protection relevant temperature ranges
which correspond to the values of the EC-type examination. For explosion protection relevant ambient temperatures (ATEX, IECEx,
EAC-Ex) please refer to chapter 2.1 –Explosion Protection)
8
The available stainless steel materials dispose of different specific characteristics such as mechanical and chemical resistance. It is
possible to optimize the corrosion behavior in highly acidiferous environments or at offshore applications by selecting the applicable
housing material. An electro-polished or powder-coated surface in various RAL colors (standard: RAL7035) is possible.

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 14 of 40
Housing material (optional) MNo.: 1.4301 (X5CrNi18-10),
AISI 304 / V2A
MNo.: 1.4305 (X8CrNiS18-9),
AISI 303
MNo.: 1.4401 (X5CrNiMo17-12-2),
AISI 316 / V4A
MNo. 1.4571 (X6CrNiMoTi17-12-2),
AISI 316Ti / V4A
Protective coating
9
: Standard color RAL7035 (all RAL colors
and special colors possible!), DURALMIT®
2K-PUR structure, type DSPT (isocyanate
netted, polyester modified acrylate resin, fine
structure (1.6…2.0 [mm] nozzle), surface re-
sistance ≤ 9^11[Ω], layer thickness ≤ 0.2 [mm],
screw connections, flat gaskets and cable
glands are excluded from the coating
Additional metallic/non-metallic materials
of the Ex d housing protection system: Zinced spring steel MNo.: 1.0330, PTFE with
glass microbeads (GYLON® Style 3504 blue),
silicone-coating (Silcoset 105 incl. CureAgent
28), VMQ (silicone), thermos transfer foil made
of polyester (aceton resistant), cable glands
made of brass, nickle-plated (MsNi)
Sight glass material: Borosilicate glass (Ilmadur 10/ I-420)
(DIN7080:2005-05)
Internal materials: Aluminum die cast, zinced (protection housing
of the camera module), polyamide (PA6.6/
PA2000) and polyoxymethylen (POM) isolators
and supporting adapters, T08 aluminum univer-
sal adapter (EN AW-ALSi1MgMn), PTC-
ceramics, infrared anti-reflection adapter made
of chloroprene rubber (CR4100/ Z-150), PUR
and additional thermoplastic plastics, optical
and electronical components etc.
9
The protective coating of the housing underlies the explosion protection! Affected are exclusively the outside metal surfaces. The
gaps preventing the transmission of an ignition / threads as well as the sealings remain unaffected. The modification of the housing
surface meets the requirements acc. to DIN EN 60079-0: 2012 chapter 7 –non-metallic housings and non-metallic housing compo-
nents (UV resistance, temperature index TI or relative heat index RTI-mechanical acc. to ANSI/UL 746B or heat and cold resistance).
The avoidance of electrostatic charges is reached by the surface resistance ≤ 9^11 Ω (max. 50% relative humidity) and the limitation
of the layer thickness to 0.2mm (IIC)/ 2mm (IIB). Due to the surface coating, the thermal value and the convection cooling changes.
The maximum permitted power loss feed into the housing is not affected by it!

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 15 of 40
Attention: The Axis module is equipped with an
ML614R battery which supplies the real time
clock (RTC). These lithium button celsl (3.0 V)
dispose of 1.2 dimethoxymethane; ethylengly-
coldimethylether (EGDME), CAS-No. 110-71-4
Weight (without accessories): 4700 g (with „K1“ cable gland flange)
5950 g (with „K2“ cable gland flange)
6600 g (PoE+)
Weight accessories: 900 g (wall mount bracket WMB-L)
700 g (wall mount bracket WMB-S)
800 g (Twin adapter WMB-xTA)
650 g (Hood WPR-VA2.1)
100 g (Hinge attachment SCH-VA2.x)
450 g (clamp attachment CMB-S)
1000 g (Samcon cool.Jacket)
Further accessories upon request!
Dimension Housing (BxHxT)
10
: 113.0mm x 138.5mm x 210.2mm (K1 flange)
113.0mm x 138.5mm x 226.0mm (K2 flange)
113.0mm x 138.5mm x 260.2mm (PoE+)
Fitting of the flame proof gap preventing the transmission of ignition (cylinder) (EX) of the
T07-VA2.1.x.x housing:
Flange / body Nominal diameter: 91 mm (plain cylindrical)
Clearance fit: H8 f7 (DIN ISO 286)
Tolerance: (-71…-36) µm … (0…+54) µm
Gap length > 12.5mm (acc. to DIN EN 60079-1)
largest gap length < 0.15mm (DIN EN 60079-1)
Average surface finish: Ra≈2.0 µm
(DIN ISO 468) / Ra≤6.3 µm acc. to DIN EN
60079-1: 2008 [5.2.2]
Cable glands 2 x M20*1.5_12 mm (ISO metrical fine thread
acc. to DIN13-2), quality 6H (medium or fine
acc. to ISO 965-1 / ISO 965-3), support-
ing/gripping threads ≥ 5 (acc. to requirements of
DIN EN 60079-1: 2008 [5.3]
table 3 „Cylindrical gaps“)
10
Dimension stainless steel housing T07 VA2.1.x.x with mounting, without cable gland, without external accessories, for further / more
detailed dimension please refer to chapter 10 –Technical Drawings

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 16 of 40
Media resistance: Checked upon request only!
Generally: Resistance to corrosion as well as
chemically high-resistance to a variety of sub-
stances used in the industrial environment and
suitable for offshore applications (q.v. the gen-
eral specifications of stainless steel MNo.:
1.4404, surface finish of the Ex d housing, Gy-
lon flat sealing etc.)
- The resistance significantly depends on the
following factors: Temperature, concentration,
duration and media type (liquid, gas, steam
etc.). The resistance towards environmental in-
fluences and mechanical strain can be maxim-
ized by an optional certified protective coating!
To increase the corrosion characteristics it is
also possible to electro-polish the applicable
components -
3 Safety guidelines
Please observe the safety guidelines indicated in the current version of the T08
ExCam series EX installation manual!

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 17 of 40
4 Illustration of the model key
The following model options are currently available for the T08 ExCam IPM1145-(L):
Model options
Ex product name1)
Type2)
Housing
combination3)
Gas expl.
group4)
Cable length
[m] SKD02-T
/Ölflex®440P5)
Cable
Termin.6)
Temp.
range7)
ExCam IPM1145
ExCam IPM1145-L
T08-
VA2.1.K1.BOR-
C-
005-
K-
N
T08-
VA2.1.K1.BOR-
C-
005-
P-
N
T08-
VA2.1.K2.BOR-
C-
005-
K-
N
T08-
VA2.1.K2.BOR-
C-
005-
P-
N
T08-
VA2.1.K1.BOR-
C-
005-
K-
L
T08-
VA2.1.K1.BOR-
C-
005-
P-
L
T08-
VA2.1.K2.BOR-
C-
005-
K-
L
T08-
VA2.1.K2.BOR-
C-
005-
P-
L
T08-
VA2.1.K1.BOR-
C-
005-
K-
LL
T08-
VA2.1.K1.BOR-
C-
005-
P-
LL
T08-
VA2.1.K1.BOR-
C-
005-
K-
H
T08-
VA2.1.K1.BOR-
C-
005-
P-
H
T08-
VA2.1.K1.BOR-
C-
005-
K-
LH
T08-
VA2.1.K1.BOR-
C-
005-
P-
LH
…PoE+
T08-
VA2.2.K1.BOR-
C-
x
x
x
Table 4.1 –Model key
Explanation:
1) ExCam IPM1145-(L) =Functional camera description of the T08 ExCam Series regarding the
installed camera module and characteristics: Sensor resolution, light sensi-
tivity, camera angle of view, aperture control, power intake, zoom charac-
teristics (wide/tele range, optical/digital, motor controlled/varifocal), special
features (e.g. IR LEDs, Lightfinder or WDR technology) etc.
2) T08 = Production type concerning the certifications of the „T08
ExCam Series“, EC type examination: „TÜV 14 ATEX 7539
X_1st supplement“, „IECEx TUR 14.0026X_1st supplement“and EAC-Ex
TC-RU-C-DE.MIO62.B.01921“
3) VA2.1.K1.BOR = T07 Ex d housing with large diameter (ØVA=113 mm) and large sight glass
(QBOR=72 mm) effective, translucent area)
VA2.1.K1.BOR = T07 housing with minimum body length
VA2.2.K1.BOR = T07 housing with medium body length
VA2.1.K1.BOR = K1 cable gland flange (straight cable gland(s) - Standard -
VA2.1.K2.BOR = K2 cable gland flange (orthogonal cable gland)
VA2.1.K1.BOR = Borosilicate sight glass DIN7080 (standard execution, for video cameras
within visible spectral range: λ= 350…2000 [nm]. Not suitable for thermo-
graphic applications)
4) C= Explosion group IIC/ IIIC (Standard execution. Suitable for all

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 18 of 40
gases includinghydrogen, acetylene, carbon disulfide, flammable fibrous
material and non-conductive dusts)
5) 005 = Length of the connection line in meter at delivery. The standard cable
length is 5 m (minimum/maximum cable length: 001…100 [m])
Information: According to DIN EN 60079-14:2014 [chapter 10.6.2]) it is, at
a cable length of ≥3 m, possible to use cable glands without an integrat-
ed pressure barrier as well as an elastomer sealing on the outer sheath
and an additional strain relief. At a cable length of < 3, the cable gland has
to be carried out with an integrated pressure barrier, this means with
epoxide compound grouting of the single conductors and with duroplast /
elastomer sealing on the outer sheath, dimensioned appropriately! The di-
mension of the cable glands are hence variable.
6) K= Terminal block termination (standard)
SKD02-T: CAT6a, 8x single conductor AWG22/1 „twisted pair“ solid
conductor copper blank, 0.33 mm2 / Ø=0.64 mm, approx. 6
mm striped, 1x shield CU-braid tinned 1.5 mm2 with ferules
blue
Ölflex 440P: Supply, 3G1.5mm2, Cu Sheath about 12 cm stripped and
furnished with bend relief / shrink tubing
P= Plug- termination (optional)
SKD02-T: CAT6a, RJ-45 network plug (heavy duty), AWG 26-22,
e.g.: Type Weidmüller „IE-PS-RJ45-FH-BK“ or type
Phoenix Contact „VS-08-RJ45-5-Q/IP20“, contact assign-
ment always acc. to specification EIA/TIA-568B 1
Ölflex 440P: Q.v. terminal block termination
Plug-termination n/aor upon request
(7) N= Normal ambient temperature range (MTBF): TAMB_N: 0 to +40 [°C]
L= Low ambient temperature range (MTBF): TAMB_L: -30 to +40 [°C]
LL = Lowest ambient temperature range (MTBF): TAMB_LL: -60 to +40 [°C]
H= High ambient temperature range (MTBF): TAMB_H: 0 to +70 [°C]
LH = Broad ambient temperature range (MTBF): TAMB_LH: -30 to 70 [°C]
Note:
The upper temperature limits of type H and type LH of the functional temperature range (MTBF)
depend on the maximum power consumption of the applicable model options and are limited by the
explosion proof temperature range. Currently, model options ExCam IPM1145 and the ExCam
IPM1145-L are available. For the ExCam IPM1145-L, the upper temperature limit is reduced to:
TAMB …+65°C (T5).

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 19 of 40
5 Commissioning
Attention!
Please observe the national regulations regarding security, installa-
tion, and accident prevention (e.g. DIN EN 60079-14 or DIN VDE 0118-
1:2010-02) for the erecting of electrical plants in mining etc.) as well as
the safety guidelines described in this user manual and the EX instal-
lation manual!
Attention!
Please observe the installation and commissioning advices described
in the ATEX/ IECEx/ EAC-Ex Ex-installation manual!
5.1 Step 1: Installation
Install the ExCam®IPM1145-(L) at the desired location. Mounting options and conditions,
accessories, as well as safety guidelines are described in the EX installation manual of
the T08 ExCam®series.
5.2 Step 2: Electrical connection
Attention!
The electrical connection of the equipment must be executed by quali-
fied personnel only!
Attention!
It is mandatory that the housing of the ExCam®Series has to be
grounded via a PE-connection!
Attention!
The minimum cable length of the connection line must not be less
than one meter! The connection cable has to be laid in a protected
manner!
Attention!
Please observe the national regulations regarding security, installa-
tion, and accident prevention (e.g. DIN EN 60079-14 VDE 0118-1:2010-
02), as well as the safety guidelines described in this user manual and
the EX installation manual!

Doc.-ID: 150903-PT08BA-TG-ExCam IPM1145-(L)_en_rev.02.docx, page 20 of 40
The ExCam®IPM1145-(L) Series is delivered with the electrical connection cable type
SKD02-T suitable for the hazardous area. Optionally, the camera can dispose of a power
cable (standard is a type „Ölflex® 440P“).The maximum cable length is 100 m (depend-
ing on electromagnetic tolerance) and can be determined individually to reflect the partic-
ular customer specifications. The minimum cable length is 1 meter.
Die ExCam®IPM1145-(L) is manufactured with a pigtail reflecting the desired cable
length. Any electro-technical work inside the camera’s flameproof enclosure done by the
user is prohibited. Depending on the model option, the ending of the camera’s cable con-
nection is either stripped to the blank Cu conductors or furnished with a plug.
5.2.1 Potential equalization
Figure 5.1 –ExCam IPM1145-(L) potential equalization
The potential equalization / earthing of the camera housing is mandatory in order to avoid
electrostatic charging and hence spark generation. The screw terminal at the lower right
hand side of the housing’s rear side is intended for that purpose (q.v. figure 5.1). The pro-
file of the potential equalization has to reflect the national grounding instructions (min.
4mm2).
Connection table:
Potential
Color (IEC 60757)
Profile
Comment
PE
GN/YE
4 mm2(fix)
Screw terminal: Slotted screw M4 x 0.7 (DIN
84) with washer Ø 9 mm (DIN 125A)), 3Nm
Tightening torque has to be observed!
Table 5.1 –Potential equilization