Samcon ExCam IPQ6055 User manual

ExCam IPQ6055
User manual

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 2 of 24
Content
1Introduction ..............................................................................................................4
2Technical Data..........................................................................................................5
2.1 Parameters of the explosion protection...............................................................5
2.2 Electrical parameters of the camera....................................................................5
2.3 Electrical parameters of the heating (optional)....................................................6
2.4 System Cable SKDxx..........................................................................................6
2.5 Supply cable (optional)........................................................................................6
2.6Video technical data............................................................................................7
2.7 Other technical data............................................................................................7
3Safety guidelines......................................................................................................8
4Illustration of the model key....................................................................................8
5Commissioning ......................................................................................................10
5.1 Step 1: Installation.............................................................................................10
5.2 Step 2: Electrical connection.............................................................................10
5.2.1 Potential equalization...............................................................................................................11
5.2.2 Connection and protection.......................................................................................................12
5.2.3 Tests prior to switching on voltage ..........................................................................................16
5.3 Optional steps ...................................................................................................17
5.3.1 Work preparation .....................................................................................................................17
5.3.2 Opening the pressure-resistant housing..................................................................................18
6Network access and visualization ........................................................................19
6.1 Browser Support................................................................................................19
6.2 Assigning the IP address...................................................................................19
6.3 Password / Identification ...................................................................................20
7Maintenance / Servicing / Alterations...................................................................21
8Repairs and Maintenance......................................................................................21
9Disposal / Recycling ..............................................................................................21
10 Drawings & 3D models.......................................................................................22
11 Notes....................................................................................................................23

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 3 of 24
Table of Figures
Table 4.1 –Model key.......................................................................................................8
Figure 5.1 –ExCam IPQ6055 potential equalization.......................................................11
Table 5.1 –Potential equilization.....................................................................................11
Figure 5.2 –ExCam IPQ6055 T08-TNXCD-C-XXX-K-N .................................................12
Figure 5.3 –ExCam IPQ6055 T08-TNXCD--XXX-P-N....................................................12
Figure 5.4 –ExCam IPQ6055 T08-TNXCD-C-XXX-K-L(L) .............................................13
Figure 5.5 –ExCam IPQ6055 T08-TNXCD-C-XXX-P-L(L) .............................................13
Table 5.2 –Pin assignment SKDxx and plug contact RJ45.............................................14
Figure 5.6 –RJ45 Contact assignment ...........................................................................15
Figure 5.7 –SKDxx Pin assignment................................................................................15
Table 5.3 –Pin assignment supply cable ........................................................................16
Figure 6.1 –Axis IP Utility................................................................................................20
Revision history
Product: T08 ExCam® IPQ6055
Titel: User manual ExCam®IPQ6055
Doc. -Id. 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx
Author: Dipl.-Ing. (FH) Eva Schneider
Date: March 30, 2017
Rev.-
Index
Date
Name
Comment
Approved by EX Officer
0
March 30,
2017
E.Schneider
Compilation of the document
(Derived from the document 160530-PT08BA-
SS-ExCam IPQ6045_en_rev.00)
1
Avril 09, 2018
E.Schneider
Correction of Links in chapter 10,
Revision of some pictures
Digital
unterschrieben von
Steffen Seibert
DN: cn=Steffen
Seibert, o=SAMCON,
ou,
email=s.seibert@sam
con.eu, c=DE
Datum: 2018.04.11
09:21:57 +02'00'

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 4 of 24
1 Introduction
The ExCam IPQ6055 is a high performance IP dome camera of the latest generation with
a 2 megapixel resolution of 1920 x 1080p pixel. It is certified according to ATEX, IECEx,
and EAC-Ex.
The dome camera has a continuous 360° pan and a 180° tilt function; the adjustment of
the picture is done automatically. A special feature is the high speed and precession with
which the pan as well as the tilt functions is carried out.
The ExCam Series is certified according the European ATEX directive as well as to the
international IECEx directive. The ex-protective housing is suitable for the usage within
the Ex zones 1, 2, 21 and 22 including the gas group IIC and the dust group IIIC. It is al-
so certified according to EAC-Ex.
During the design of the ExCam IPQ6055, the main focus was put on security as well as
on mechanical precision and high-quality stainless steel. In addition, the modular design
allows, for example, a connection via FOC.

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 5 of 24
2 Technical Data
2.1 Parameters of the explosion protection
Identification marks according to
directive 2014/34/EU: II 2G (Zone 1 and 2)
II 2D (Zone 21 and 22)
Explosion protection (gas): Ex d IIC T6 Gb or
Ex d IIC T5 Gb or
Ex d IIB T6 Gb or
Ex d IIB T5 Gb
Explosion protection (dust): Ex tb IIIC T80°C Db IP68 or
Ex tb IIIC T95°C Db IP68
Protection level: IP 66/68 (IEC /EN 60529)
Transportation and storage
temperature (EX): -40°C…+60°C
Ambient temperature (EX)
1
: -50°C…+50°C (T6)
Noticed body: TÜV Rheinland (number 0035)
EU Type Examination: TÜV 14 ATEX 7539 X
IECEx TUR 14.0026X
Test protocol ATEX: 557/Ex.539.00/14
Test report IECEx: DE/TUR/ExTR14.0026/00
Quality Assessment Report: DE/BVS/QAR14.0006/00
2.2 Electrical parameters of the camera
Axis Q6055
Power supply: PoE, IEEE 802.3at Class 4
Reference power: 48 V DC (44...54 V DC)
Maximum power input: 30 W
1
Maximum ambient temperature range relevant for explosion protection might deviate to the maximum functional temperature range.
For maximum functional temperature range (MTBF) see chapter 2.12

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 6 of 24
2.3 Electrical parameters of the heating (optional)
Power supply: 12…30 V DC
Reference power: 24 V DC
Maximum power input: 40W @-30°C
60W @-50°C
Suggested fuse supply cable: 6000mA –T at 3G 1.5 mm2
2.4 System Cable SKDxx
Description: Data transfer and power supply of the camera
module (DIN EN 60079-14 conform)
Color of sheath: Green (GN), similar RAL6018
Outer diameter: 9.1 mm ± 0.2 mm
Bending radius: 100 mm
Cable: 4 x 2 x AWG22/1 CAT.6a
Characteristics: PUR halogen free, flame retardant, UV
resistant, chemical resistance, shielded
Interface: P version: RJ-45 (EIA/TIA-568B)
10BASE-T/100BASE-TX PoE
K version: 8x single pin twisted pair (solid
conductor 0.64 mm2, about 5 mm stripped)
1x shield (Cu braid 2.5 mm2, ferules)
10BASE-T/ 100BASE-TX PoE
2.5 Supply cable (optional)
Description: Power supply of the heating elements including
temperature controller, Ölflex® 440p
2
(DIN EN 60079-14 conform)
Color of sheath: Black (BK) matt, similar RAL9005
2
Further cables available upon request, e.g. „Ölflex® Petro FD 865 CP“ (high resistance against oil and drilling liquids) or „XPLE
Armoured 3 x 2.5“ (extremely robust, particularly designed for offshore environments)

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 7 of 24
2.6 Video technical data
For details regarding video technical data of the installed AXIS Q6055 dome camera,
please refer to the AXIS®product documentation:
http://www.axis.com/us/en/products/axis-q6055
2.7 Other technical data
Permitted ambient
temperature (MTBF)
3
: 0 °C … +50 °C (type N)
-30 °C … +50 °C (type L)
-50 °C … +50 °C (type LL)
Protection level EN 60529/IEC 529: IP 68
Test conditions: 24 h/ 3 m water column at
5 °C. An additional mechanical protection
against water jets is recommended
Housing material: Stainless steel MNo.: 1.4404
(X2CrNiMo17-12-2), AISI 316L (V4A)
Material sight glass: LEXAN
Weight: 15 kg
Dimensions housing (WxHxD): D195 mm x 378 mm
3
Functional temperature range concerning the operational temperature range of the installed components according to manufacture
declarations (MTBF –meantime ration duration between failures). For ambient temperature ranges relevant for explosion protection
(ATEX, IECEx) see chapter 2.1 –Explosion protection)

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 8 of 24
3 Safety guidelines
Please observe the safety guidelines indicated in the EX installation manual of the
T08 ExCam series!
4 Illustration of the model key
The following model options are currently available for the ExCam IPQ6055:
Model options
Ex product name1)
Type2)
Housing
combination3)
Gas expl.
group4
Cable length/m
SKDxx/SKLxx5)
cable
termin.6)
Temperature
range7)
ExCam IPQ6055
T08-
TNXCD
B-
005-
K-
N
T08-
TNXCD-
B-
005-
P-
N
T08-
TNXCD-
C-
005-
K-
N
T08-
TNXCD-
C-
005-
P-
N
ExCam IPQ6055
T08-
TNXCD-
B-
005-
K-
L
T08-
TNXCD-
B-
005-
P-
L
T08-
TNXCD-
C-
005-
K-
L
T08-
TNXCD-
C-
005-
P-
L
ExCam IPQ6055
T08-
TNXCD-
B-
005-
K-
LL
T08-
TNXCD-
B-
005-
P-
LL
T08-
TNXCD-
C-
005-
K-
LL
T08-
TNXCD-
C-
005-
P-
LL
Table 4.1 –Model key
1) ExCam IPQ6055 = Functional camera description of the ExCam IPQ6055 network camera
(Basis: AXIS Q6055)
2) T08 = Certified production type, device designation „T08 ExCam series“, EU type
examination: „TÜV 14 ATEX 7539 X“ and „IECEx TUR 14.0026X“
3) TNXCD = Ex-d housing
4) B= Explosion group IIB/ IIIB (Standard - all gases except hydrogen, acetylene,
carbon disulfide, flammable fibrous materials, and non-conductive dusts)
C= Explosion group IIC/ IIIC (optional - all gases, flammable fibrous materials,
and conductive dusts)
5) 005 = Length of the connection line in meter at delivery. The standard cable
length is 5 m (minimum/maximum cable length: 001…100 [m])

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 9 of 24
6) K= Terminal block execution (standard)
SKDxx: 8 x single pin twisted pair (solid conductor 0.64 mm2, about
5 mm stripped), 1x shield (Cu braid 2.5 mm2, ferules)
Supply: („Ölflex 440p2 x 2.5 mm2 Cu litz wire with ferule, sheath
about 10 cm stripped and furnished with bend relief/shrink
tubing
P= Plug termination (optional)
SKDxx: RJ-45 network plug (heavy duty), AWG 26-22.
Pin assignment according to EIA/TIA-568B
Supply: („Ölflex 440p“) n.a. / upon request
7) N= Normal ambient temperature range (MTBF): TAMB_N: 0 …+50 [°C]
L= Low ambient temperature range (MTBF): TAMB_L: -30 … +50 [°C]
LL = Lowest ambient temperature range (MTBF): TAMB_LL: -50 … +50 [°C]

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 10 of 24
5 Commissioning
Attention!
Please observe the national regulations regarding security, installa-
tion, and accident prevention (e.g. DIN EN 60079-14) as well as the
safety guidelines described in this user manual and the EX installation
manual!
Attention!
Please observe the installation and commissioning advices described
in the Ex installation manual!
5.1 Step 1: Installation
Install the ExCam®IPQ6055 at the desired location. Mounting options, accessories, as
well as safety guidelines are described in the EX installation manual of the ExCam®se-
ries.
5.2 Step 2: Electrical connection
Attention!
The electrical connection of the equipment must be executed by quali-
fied personnel only!
Attention!
It is mandatory that the housing of the ExCam®Series has to be
grounded via a PE-connection!
Attention!
The minimum cable length of the connection line must not be less
than one meter! The connection cable has to be laid in a protected
manner!
Attention!
Please observe the national regulations regarding security, installa-
tion, and accident prevention (e.g. DIN EN 60079-14), as well as the
safety guidelines described in this user manual and the EX installation
manual!

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 11 of 24
The ExCam ® IPQ6055 is delivered with an electrical connection cable type SKDxx (Sys-
tem Kabel Digital) and optional with an additional supply cable e.g. of the type „Ölflex®
440p“. The maximum cable length is 100 m (depending on electromagnetic tolerance)
and can be determined individually to reflect the particular customer specifications. The
minimum cable length is 1 meter.
The ExCam®IPQ6055 is manufactured with a pigtail reflecting the desired cable length.
Any electro-technical work inside the camera’s flameproof enclosure done by the user is
prohibited. Depending on the model option, the ending of the camera’s cable connection
is either stripped to the blank Cu conductors or furnished with a plug.
5.2.1 Potential equalization
Figure 5.1 –ExCam IPQ6055 potential equalization
The potential equalization / earthing of the camera housing is mandatory in order to avoid
electrostatic charging and hence spark generation. The screw terminal at the lower right
hand side of the housing’s rear side is intended for that purpose (q.v. figure 5.1). The pro-
file of the potential equalization has to reflect the national grounding instructions (mini-
mum 4 mm2).
Connection table:
Potential
Color (IEC 60757)
Profile
Comment
PA
GN/YE
4 mm2(fx)
-
Table 5.1 –Potential equilization

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 12 of 24
5.2.2 Connection and protection
Figure 5.2 –ExCam IPQ6055 T08-TNXCD-C-XXX-K-N
Figure 5.3 –ExCam IPQ6055 T08-TNXCD--XXX-P-N

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 13 of 24
Figure 5.4 –ExCam IPQ6055 T08-TNXCD-C-XXX-K-L(L)
Figure 5.5 –ExCam IPQ6055 T08-TNXCD-C-XXX-P-L(L)

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 14 of 24
The green patch cable SKDxx disposes of 8(+1) conductors used for the data transfer
with other network devices as well as to power the camera. In order to guarantee the
power supply (Power Device, PD) of the ExCam IPQ6055 (power device, PD) a Power-
over-Ethernet component (Power Sourcing Equipment, PSE) has to be available at the
connecting side (e.g. a PoE Switch, a PoE Injector, or Midspan) which meets the specifi-
cation IEEE 802.3at with class 4 (HiPoE, PoE+ (30W). A 100 Mbit Ethernet Connection
(100BASE-TX) is used for the ExCam IPQ6055 data transfer.
In case the camera disposes of a plug, (figure 5.4); it has to be plugged into the RJ45
PoE slot of the network device. Due to the design, a faulty connection or pin assignment
is not possible. The network device can already be supplied with power, prior to connect-
ing it to the camera, hence there is no „power ON“ priority which has to be observed.
In case the ExCam IPQ6055 disposes of a terminal block termination, the correct con-
nection of the individual pins in accordance with EIA/TIA-568B has to be observed (q.v.
table 5.2). Generally, the pins of the same color code are connected. Only use SAMCON
approved clamps!
It is allowed to separate the ExCam IPQ6055 from the network and to switch it on again
while in operation or in interaction with a visualization, video management system or
while accessing the web inteface (hot plugging).
Attention: „Hot plugging“ as well as the connection and separation of the data and
power cable SKDxx with/of network devices and terminal blocks under power is
only allowed within the safe area (non-hazardous atmosphere)!
The pin assignment of the SKDxx according to EIA/TIA-568B standard for 100BaseTX
with PoE (IEEE 802.3at) is done as follows:
Pin / Potential
Color
SKDxx
(IEC60757)
Plug /
pin contact
(TIA-568B)
Cross sec-
tion area
Remarks
Mode A
Mode B
Tx+ / PoE ±48 VDC
Tx+
WH / OG
1
0.32 mm2
Solid conductor
Tx- / PoE ±48 VDC
Tx-
OG
2
0.32 mm2
Solid conductor
Rx+ / PoE GND
Rx+
WH / GN
3
0.32 mm2
Solid conductor
n.a.
PoE +48 VDC
BU
4
0.32 mm2
Solid conductor
n.a.
PoE +48 VDC
WH / BU
5
0.32 mm2
Solid conductor
Rx- / PoE GND
Rx-
GN
6
0.32 mm2
Solid conductor
n.a.
PoE GND
WH / BN
7
0.32 mm2
Solid conductor
n.a.
PoE GND
BN
8
0.32 mm2
Solid conductor
shield/ GND
(complete conductor bunch)
BK
9
2.5 mm2
Shield braid of
tinned copper
wires Ø=0.13 mm
(AWG 36)
shield
(single, twisted pair pins)
n.a.
n.a. / 10
n.a.
Aluminum synthe-
tic strapp, twisted
Table 5.2 –Pin assignment SKDxx and plug contact RJ45

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 15 of 24
Figure 5.6 –RJ45 Contact assignment
Particularly in EMC critical environments, it is important to earth the shield at the terminal
block side (q.v. figure 5.3 –pin with black shrink tubing and blue ferule).
Figure 5.7 –SKDxx Pin assignment
In case the ExCam IPQ6055 is supplied via a PoE capable device, an additional safe-
guarding of the power supply is not necessary. The power supply is executed by the PoE
network device via an electronic with intelligent set-up. The camera as well as the con-
nection is permanently monitored in order to avoid any failure or defects in case of a
short-circuit fault.
For a camera with terminal block execution, it is possible to operate the camera either
with a PoE capable network device or with a separate 48 V DC power supply (supply
voltage and network streams are self-sustaining). In this event an adequate supply safe-
guarding has to be dimensioned.
Recommended is a 300 mA medium time lag fuse.
4
2
6
3
9 (shield/
GND)
5
8
7
1
10 (shield)
9

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 16 of 24
If the Ex CCTV application calls for a separate 48 V DC supply voltage, the wire/pin as-
signment has to reflect Mode B operation mode (q.v. table 5.2)!
If the camera is equipped with a heating (type L or type LL), a second power supply with
a separate supply protection at the „L+“ has to be available. Standardly the supply is car-
ried out via the supply cable Ölflex® 440p. Connection assignment and supply protection
according to table 5.3.
Potential/
Pin no.
Color „Ölflex
440p“
(IEC60757)
Cond.
design
Voltage
Maximum power in-
put / protection
(type L)
Maximum power in-
put / protection
(type LL)
L+ / 1
BK
2.5 mm2
litz wire
+24 VDC
40 W / fuse (L+) 6000
mA -T- time lag
(high inrush current!)
60 W / fuse (L+) 6000
mA -T- time lag
(high inrush current!)
L- / 2
BK
2.5 mm2
litz wire
0 VDC / GND
Table 5.3 –Pin assignment supply cable
5.2.3 Tests prior to switching on voltage
Attention!
Prior to commissioning, all tests as indicated by the national regula-
tions have to be executed. In addition, it is mandatory that the proper
functioning of the operating device in accordance with this user man-
ual and all other applicable regulation has been executed.
Attention!
Incorrect installation and operation of the camera may lead to a loss of
warranty!
Attention!
When powering the camera on in ambient temperatures less than 0°C
(storage temperature), make sure to heat up the enclosure before
switching on the camera circuit. For non-continuous systems please
use an adequate time relay to switch on the heater, before the camera
circuit is switched on!

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 17 of 24
5.3 Optional steps
5.3.1 Work preparation
Attention!
Please carry out any preoperational work carefully and in accordance
with the applicable regulations
Attention:
Note: Depending on the zone classification, it might be necessary to
obtain a work permit/clearance! When adjusting the camera settings
potentially explosive atmosphere must be avoided by any means!
To allow the camera delivering the best picture quality, please consider the lighting
conditions, the object distance and size, the angle of view as well as the minimum object
distance for focusing when selecting the installation place.
Use appropriate tools
Make sure you have a secure foothold
Avoid static charge

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 18 of 24
5.3.2 Opening the pressure-resistant housing
The opening of the TNXCD housing requires special tools and it is not intended that cus-
tomer open the housing. In case that due to an unforeseeable event the housing has to
be opened, inform SAMCON Support ([email protected]) prior to executing any
measures.
Always observe all ex-relevant restrictions:
„WARNING – DO NOT OPEN IN HAZARDOUS AREA“
Note: Depending on the zone classification, it might be necessary to
obtain a work permit/clearance! Even after disconnection of the volt-
age, it is mandatory to avoid potentially explosive atmosphere when
opening the camera housing (de-installation of the camera and execu-
tion of the work within the safe area (non EX)!
Attention!
Beware not to damage the surface of bore hole and shaft (fit) at the
flame proof gap preventing the transmission of ignition.
Attention!
Please make sure not to damage housing sealings and to keep them
clean

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 19 of 24
6 Network access and visualization
In the following, the most important steps for the initial commissioning of the camera are
described. The configuration menu of the web surface allows an intuitive navigation and
offers several configuration possibilities. For a comprehensive user manual of the web
surface, please refer to the to the Axis user manual, also available at the following link:
http://www.axis.com/us/en/products/axis-q6055
At delivery, the ExCam IPQ6055 is set to the applicable net frequency (50Hz or 60Hz). If
the camera is used at a location with a differing net frequency, a flickering of the picture
might be noticeable, particularly in surroundings with fluorescent tubes. In such a case,
the applicable settings have to be carried out within the menu “System Options > Ad-
vanced > Plain Config”
User: root
Password: root
6.1 Browser Support
A list with the currently supported web browsers, operating systems, and required add-
ons can be viewed at:
http://www.axis.com/techsup/cam_servers/tech_notes/browsers.htm
6.2 Assigning the IP address
The ExCam IPQ6055 is an Ethernet network camera requiring an IP address to access it.
Usually, a DHCP server is integrated in most networks which automatically assigns an IP
address.
In case no DHCP server is available in the network, the ExCam IPQ6055’s default IP
address is 192.168.0.90 (subnet masking 255.255.255.0).
Using the AXIS IP Utility is the suggested procedure to determine the IP address under
Windows. The application is available for download at:
http://www.samcon.eu/en/info-center/drivers-software/
In case it is not possible to assign the IP address, it might be necessary
to change the firewall settings!

Doc.-ID: 180409-PT08BA-SS-ExCam IPQ6055_en_rev.01.docx, page 20 of 24
The “AXIS IP Utility“ tool automatically recognizes all ExCam devices and displays them.
It can also be used to manually assign a static IP address. Please note that the ExCam
IPQ6055 network camera has to be installed within the same network segment (physical
subnet) as the computer on which the “AXIS IP Utility” tool is executed. For example, the
ExCam IPQ6055 network identification is „Axis Q6055“ (q.v. figure 6.1). MAC address
and serial number are also determined and displayed so that a non-ambiguous identifica-
tion is possible.
Figure 6.1 –Axis IP Utility
6.3 Password / Identification
The default user name is: root
The default password is: root
ExCam IP1365
ExCam IPQ6055
Axis Q6055