Samsung 310 5G CPE User manual

Radio Access Network
310 5G CPE Outdoor
Installation Manual
Describes product installation and requirement procedure.
Document Version 1.0
February 2018
Document Number: 2600-00LVNAGAA

© 2018 SAMSUNG Electronics Co., Ltd.
All Rights Reserved. The contents of this document/presentation contain proprietary information that
must be kept confidential. No part of this document shall be photocopied, reproduced, stored in a
retrieval system, or transmitted, in any form or by any means whether, electronic, mechanical, or
otherwise without the prior written permission of SAMSUNG Electronics Co., Ltd.
No warranty of accuracy is given concerning the contents of the information contained in this
publication. To the extent permitted by law no liability (including liability to any person by reason of
negligence) will be accepted by SAMSUNG Electronics Co., Ltd., its subsidiaries or employees for
any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
SAMSUNG Electronics Co., Ltd. reserves the right to change details in this publication without
notice.
This manual should be read and used as a guideline for properly installing and/or operating the
product.
This manual may be changed for system improvement, standardization and other technical
reasons without prior notice.
Updated manuals are available at:
https://systems.samsungwireless.com/
For questions on the manuals or their content, contact
NetSys Tech Write[email protected]amsung.com

Confidential
5G CPE Outdoor Installation Manual v1.0 iii
Copyright © 2018, All Rights Reserved.
Contents
Preface viii
Conventions in this Document.......................................................................................................viii
Revision History............................................................................................................................... ix
Organization of This Document ...................................................................................................... ix
Related Documentation .................................................................................................................. ix
Personal and Product Safety ............................................................................................................ x
Equipment Markings .......................................................................................................................xii
Chapter 1 Before Installation 1
System View and External Interface ................................................................................................ 1
CPE Outdoor View........................................................................................................................ 1
CPE Outdoor External Interface ................................................................................................... 3
Specifications ................................................................................................................................... 4
Cautions for Installation ................................................................................................................... 5
Before Installing........................................................................................................................... 5
While Installing ............................................................................................................................ 5
After Installing ............................................................................................................................. 6
Installation Tools .............................................................................................................................. 7
Chapter 2 Installing System 9
Installation Procedure...................................................................................................................... 9
System Arrangement ..................................................................................................................... 10
Transporting and Unpacking .......................................................................................................... 11
Bringing in Items........................................................................................................................ 11
Unpacking Items ........................................................................................................................ 11
Fixing System.................................................................................................................................. 13
Inserting SIM.............................................................................................................................. 13
Fixing Unit Bracket Assembly..................................................................................................... 15
Fixing System on a Pole Type..................................................................................................... 16
Fixing System on a Wall Type .................................................................................................... 20
System Tilting & Swiveling ......................................................................................................... 25
Chapter 3 Connecting Cables 30
Cabling Procedure .......................................................................................................................... 30
Guidelines for Cable Connections .................................................................................................. 31
Cable Path Inspection ................................................................................................................ 32
Cable Cutting ............................................................................................................................. 32
Cable Installation ....................................................................................................................... 32
Cable Binding ............................................................................................................................. 33
Connector Attachment............................................................................................................... 33
Identification Tag Attachment................................................................................................... 34
Cabling Diagram ............................................................................................................................. 35
Grounding ...................................................................................................................................... 36
Connecting Ground Cable .......................................................................................................... 36
Power Cabling ................................................................................................................................ 39
Connecting PoE Midspan Power Cable ...................................................................................... 39
Interface Cable Connection............................................................................................................ 41
Remove Ethernet Cable ............................................................................................................. 41

Confidential
Contents
5G CPE Outdoor Installation Manual v1.0 iv
Copyright © 2018, All Rights Reserved.
Connecting Ethernet Cable ........................................................................................................ 43
Fixing Cable Cover .......................................................................................................................... 51
Chapter 4 Inspect the Installation 52
Appendix A Acronyms 55
Appendix B Standard Torque 56

Confidential
5G CPE Outdoor Installation Manual v1.0 v
Copyright © 2018, All Rights Reserved.
List of Figures
Figure 1. CPE Outdoor View............................................................................................................................ 1
Figure 2. CPE Outdoor View (with Cable Cover) ............................................................................................. 2
Figure 3. CPE Outdoor External Interface ....................................................................................................... 3
Figure 4. Procedure to Install the CPE Outdoor .............................................................................................. 9
Figure 5. CPE Outdoor Arrangement Pole type Installation.......................................................................... 10
Figure 6. CPE Outdoor Arrangement Wall type Installation ......................................................................... 10
Figure 7. Item List.......................................................................................................................................... 12
Figure 8. Inserting SIM (1)............................................................................................................................. 13
Figure 9. Inserting SIM (2)............................................................................................................................. 14
Figure 10. Inserting SIM (3)............................................................................................................................. 14
Figure 11. Fixing Unit Bracket Assembly (1).................................................................................................... 15
Figure 12. Fixing Unit Bracket Assembly (2).................................................................................................... 16
Figure 13. Fixing Mounting bracket on the Pole (1)........................................................................................ 17
Figure 14. Fixing Mounting bracket on the Pole (2)........................................................................................ 17
Figure 15. Fixing Mounting bracket on the Pole (3)........................................................................................ 18
Figure 16. Fixing CPE Outdoor on the Pole Mounting Bracket ....................................................................... 19
Figure 17. CPE Outdoor Marking Dimensions for Wall Type .......................................................................... 20
Figure 18. Marking Wall Type ......................................................................................................................... 21
Figure 19. Fixing Mounting Bracket on the Wall (1) ....................................................................................... 23
Figure 20. Fixing Mounting Bracket on the Wall (2) ....................................................................................... 23
Figure 21. Fixing CPE Outdoor on the Wall Mounting Bracket ...................................................................... 24
Figure 22. System Tilting (1)............................................................................................................................ 25
Figure 23. System Tilting (2)............................................................................................................................ 26
Figure 24. System Tilting (3)............................................................................................................................ 27
Figure 25. System Swiveling (1)....................................................................................................................... 27
Figure 26. System Swiveling (2)....................................................................................................................... 28
Figure 27. System Swiveling (3)....................................................................................................................... 29
Figure 28. Procedure to Connect System Cable.............................................................................................. 30
Figure 29. Cable Connection Procedure.......................................................................................................... 31
Figure 30. Cable Diagram ................................................................................................................................ 35
Figure 31. Connecting Ground Cable (1)......................................................................................................... 37
Figure 32. Connecting Ground Cable (2)......................................................................................................... 38
Figure 33. Power Equipment Elements........................................................................................................... 39
Figure 34. Connecting Power Cable (1)........................................................................................................... 40
Figure 35. Connecting Power Cable (2)........................................................................................................... 40
Figure 36. Remove Ethernet Cable (1) ............................................................................................................ 41
Figure 37. Remove Ethernet Cable (2) ............................................................................................................ 42
Figure 38. Remove Ethernet Cable (3) ............................................................................................................ 42
Figure 39. Connecting Ethernet Cable_CPE~PoE Midspan (1) ........................................................................ 44
Figure 40. Connecting Ethernet Cable_CPE~PoE Midspan (2) ........................................................................ 44
Figure 41. Connecting Ethernet Cable_CPE~PoE Midspan (3) ........................................................................ 45
Figure 42. Connecting Ethernet Cable_CPE~PoE Midspan (4) ........................................................................ 45
Figure 43. Connecting Ethernet Cable_CPE~PoE Midspan (5) ........................................................................ 46
Figure 44. Connecting Ethernet Cable_CPE~PoE Midspan (6) ........................................................................ 46
Figure 45. Connecting Ethernet Cable_CPE~PoE Midspan (7) ........................................................................ 46
Figure 46. Connecting Ethernet Cable_PoE Midspan~Home Router (1) ........................................................ 48
Figure 47. Connecting Ethernet Cable_PoE Midspan~Home Router (2) ........................................................ 48

Confidential
List of Figures
5G CPE Outdoor Installation Manual v1.0 vi
Copyright © 2018, All Rights Reserved.
Figure 48. Checking a LED (1) .......................................................................................................................... 49
Figure 49. Checking a LED (2) .......................................................................................................................... 50
Figure 50. Fixing Cable Cover on CPE Outdoor ............................................................................................... 51
Figure 51. Installation Inspection Procedure .................................................................................................. 52

Confidential
5G CPE Outdoor Installation Manual v1.0 vii
Copyright © 2018, All Rights Reserved.
List of Tables
Table 1. Specifications ................................................................................................................................... 4
Table 2. Basic Installation Tools..................................................................................................................... 7
Table 3. Parts and Tools for inserting the SIM............................................................................................. 13
Table 4. Parts and Tools for Fixing Unit Bracket on CPE Outdoor ............................................................... 15
Table 5. Parts and Tools for Fixing Mounting bracket on the Pole.............................................................. 16
Table 6. Parts and Tools for Fixing CPE Outdoor on the Pole ...................................................................... 19
Table 7. Tools for Marking ........................................................................................................................... 20
Table 8. Tools for Drilling ............................................................................................................................. 21
Table 9. Anchor Bolt Drill Bits and Hole Depth ............................................................................................ 21
Table 10. Drilling Example ............................................................................................................................. 22
Table 11. Parts and Tools for Fixing Mounting Bracket on the Wall.............................................................. 22
Table 12. Parts and Tools for Fixing CPE Outdoor on the Wall...................................................................... 24
Table 13. Tools for System Tilting .................................................................................................................. 25
Table 14. Tools for System Swiveling............................................................................................................. 27
Table 15. Recommended Minimum Allowed Cable Bending Radius............................................................. 33
Table 16. CPE Outdoor Connection Cable...................................................................................................... 35
Table 17. Parts and Tools for Connecting Ground Cable ............................................................................... 36
Table 18. Parts and Tools for Connecting Power Cable ................................................................................. 39
Table 19. Tools for Remove Ethernet Cable .................................................................................................. 41
Table 20. Parts and Tools for Connecting Ethernet Cable (CPE~PoE Midspan)............................................. 43
Table 21. Ethernet Cable Pin Map (CPE~PoE Midspan)................................................................................. 43
Table 22. Parts and Tools for Connecting Ethernet Cable (PoE Midspan~Home Router) ............................. 47
Table 23. Ethernet Cable Pin Map (PoE Midspan~Home Router) ................................................................. 47
Table 24. LED Indication ................................................................................................................................ 48
Table 25. Parts and Tools for Fixing Cable Cover on CPE Outdoor ................................................................ 51
Table 26. Construction Situation Checklist .................................................................................................... 53
Table 27. Standard Torque Value for Fastening Bolts ................................................................................... 56
Table 28. Brass Bolts Torque Value................................................................................................................ 56
Table 29. Connector Connection Torque Value............................................................................................. 56

Confidential
5G CPE Outdoor Installation Manual v1.0 viii
Copyright © 2018, All Rights Reserved.
Preface
This manual describes how to install a 5G Customer Premises Equipment (CPE)
Outdoor and how to connect its cables. This manual includes the following 5G
CPE Outdoor:
•CPE Outdoor
Conventions in this Document
Samsung Networks product documentation uses the following conventions.
Symbols
Symbol
Description
Indicates a task.
Indicates a shortcut or an alternative method.
Provides additional information.
Provides information or instructions that you should follow to avoid service
failure or damage to equipment.
Provides information or instructions that you should follow to avoid personal
injury or fatality.
Provides antistatic precautions that you should observe.
Menu Commands
menu | command
This indicates that you must select a command on a menu, where menu is the
name of the menu, and command is the name of the command on that menu.
File Names and Paths
These are indicated by a bold typeface. For example:
Copy filename.txt into the /home/folder1/folder2/bin/ folder.

Confidential
Preface
5G CPE Outdoor Installation Manual v1.0 ix
Copyright © 2018, All Rights Reserved.
User Input and Console Screen Output Text
Input and output text is presented in the Courier font. For example,
context <designated epc-context-name>
CLI commands are presented in bold small caps. For example,
Type the RTRV-NE-STS command in the input field.
Revision History
The following table lists all versions of this document.
Document Version
Publication Date
Remarks
1.0 February 2018 First version
Organization of This Document
Section
Title
Description
Chapter 1 Before Installation This chapter introduces CPE Outdoor and describes items
should be understood before installation.
Chapter 2 Installing System This chapter describes the procedures to install the CPE
Outdoor.
Chapter 3 Connecting Cables This chapter describes the procedures to connect the cables to
the CPE Outdoor installed.
Chapter 4 Inspect the
Installation This chapter describes the procedures of inspecting installation status after CPE Outdoor installation and cabling is completed.
Appendix A Acronyms This annex describes the acronyms used in this manual.
Appendix B Standard Torque This annex describes the standard torque when fastening the
bolt.
Related Documentation
•5G CPE System Description

Confidential
Preface
5G CPE Outdoor Installation Manual v1.0 x
Copyright © 2018, All Rights Reserved.
Personal and Product Safety
This product safety information includes American directives, which you must
follow. If these do not apply in your country, please follow similar directives that
do apply in your country.
Proposition 65 Warning (US Only)
State of California Proposition 65 Warning (US only)
WARNING: This product contains chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm.
Electrical
The product is designed to operate from a 120 V AC supply.
The product contains hazardous energy levels as defined by UL 60950. Care must
be taken when maintaining this equipment as injury to personnel or damage to the
equipment could result from mistakes. Maintenance should only be carried out by
trained and competent engineers who are familiar with the relevant procedures and
instructions.
Manual Handling
Care should be taken when handling equipment. Give due consideration to the
weight of the equipment, the physical capability of the individual(s) handling the
equipment, and movements such as twisting, bending and stooping, which could
lead to skeletal and muscular injuries.
Installation
Installation must be carried out by trained and competent engineers only. All
relevant safety measures should be taken to ensure equipment is not connected to
live power and transmission sources during installation. Equipment must be
correctly installed in order to meet the relevant safety standards and approval
conditions.
Maintenance
Maintenance must only be carried out by a suitably trained and competent
technician. All safety instructions must be carefully observed at all times.
Equipment covers should not be removed while live power and transmission is
connected unless in a controlled environment by trained technicians.
Fire
The product is powered from a 120 V AC supply. To protect against fire, the
equipment is fused.

Confidential
Preface
5G CPE Outdoor Installation Manual v1.0 xi
Copyright © 2018, All Rights Reserved.
Environment
The product must be operated in an environment with the specified relative
humidity and ambient temperature ranges.
Keep all liquids away from the equipment as accidental spillage can cause severe
damage.
Anti-Static Precautions
The circuit boards and other modules in the product are sensitive to and easily
damaged by static electricity. If any card or sub-assembly is removed from the
unit, the following anti-static precautions must be observed at all times:
•Service personnel must wear anti-static wrist straps.
•Circuit boards and sub-assemblies must be placed on ground conductive mats
or in conductive bags.
•All tools must be discharged to ground before use.
•The anti-static wrist strap and cord must be checked at regular intervals for
their suitability for use.
Power Supply Connection
The equipment is designed to be powered from a 120 V AC supply. Power
connections and installation of associated wiring must be carried out by a suitably
qualified technician.
Product Disposal
To reduce the environmental impact of products, Samsung has joined WEEE
compliance activities.
The WEEE symbol on the product indicates that the product is covered by the
European Directive 2002/96/CE for the disposal of Waste Electrical and Electronic
Equipment (WEEE). This means that the product should be disposed of separately
from the municipal waste stream via designated collection facilities appointed by
the government or the local authorities. This will help prevent potential negative
consequences for the environment and human health. Please check the terms and
conditions of the purchase contract for information about correct disposal.
California USA Only
This Perchlorate warning applies only to primary CR (Manganese Dioxide)
Lithium coin cells in the product sold or distributed ONLY in California USA
‘Perchlorate Material-special handling may apply, See
www.dtsc.ca.gov/hazardouswaste/perchlorate.’

Confidential
Preface
5G CPE Outdoor Installation Manual v1.0 xii
Copyright © 2018, All Rights Reserved.
Equipment Markings
This marking on the product, accessories or literature indicates that the
product and its electronic accessories (e.g. charger, headset, USB cable)
should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, please separate these items from other
types of waste and recycle them responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased
this product, or their local government office, for details of where and how
they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in countries with separate collection systems.)
The marking on the battery, manual or packaging indicates that the battery
in this product should not be disposed of with other household waste. Where
marked, the chemical symbols Hg, Cd or Pb indicate that the battery
contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66.
The battery incorporated in this product is not user replaceable. For
information on its replacement, please contact your service provider. Do not
attempt to remove the battery or dispose it in a fire. Do not disassemble,
crush, or puncture the battery. If you intend to discard the product, the waste
collection site will take the appropriate measures for the recycling and
treatment of the product, including the battery.

Confidential
5G CPE Outdoor Installation Manual v1.0 1
Copyright © 2018, All Rights Reserved.
Chapter 1
Before
Installation
This chapter introduces the CPE Outdoor and describes the items that you should
know before installation.
System View and External Interface
This section provides the pictorial view of the CPE Outdoor and its interfaces.
CPE Outdoor View
The figure below depicts the physical structure of the CPE Outdoor.
Figure 1. CPE Outdoor View
6.77 (172)
2.52
(64)
[Front View]
[Rear View]
[Right View]
Unit: in. (mm)
2.08
(53)
10.19 (259)
[Left View]
[Top View]
[Bottom View]

Confidential
Chapter 1 Before Installation
5G CPE Outdoor Installation Manual v1.0 2
Copyright © 2018, All Rights Reserved.
Figure 2. CPE Outdoor View (with Cable Cover)
[Bottom View]
[Top View]
[Left View]
13.71 (348.4)
2.08
(53)
Unit: in. (mm)
[Right View]
[Rear View]
[Front View]
6.86 (174.4)
2.52
(64)

Confidential
Chapter 1 Before Installation
5G CPE Outdoor Installation Manual v1.0 3
Copyright © 2018, All Rights Reserved.
CPE Outdoor External Interface
The figure below depicts the external interface structure of the CPE Outdoor.
Figure 3. CPE Outdoor External Interface
Ground Terminal
LAN
[Bottom View]

Confidential
Chapter 1 Before Installation
5G CPE Outdoor Installation Manual v1.0 4
Copyright © 2018, All Rights Reserved.
Specifications
The table below lists the main specifications of the CPE Outdoor.
Table 1. Specifications
Item
COF110-284
Technology 5G (follows Verizon 5GTF's latest version)
Operating Frequency 27.5-28.35 GHz
Channel Bandwidth 100 MHz
Operating Bandwidth 100 MHz × 8 Carrier
Antenna Configuration Integrated Antenna
•Data Channel: 2Tx/2Rx
•RF chain per Data Channel: 32
RF Output Power 36 dBm/Path (EIRP, Antenna Gain: 19 dBi )
Power PoE (Midspan)
* Use the power supplies that meets LPS.
Ethernet RJ45 1 Port
•PoE, 100 Base-TX or 1000 Base-T
USB USB 2.0 1 Port
Bluetooth BLE4.0
USIM
Nano-SIM 1 Port
•Replaceable regular SIM
•support Class C operating conditions: terminal or a smart card operating at 1,8 V
± 10 %
LED
Total: 4 EA
•Power: Green LED
•Signal: 3 Color (Green/Amber/Red)
•Connection: 3 Color (Green/Amber/Red)
•Alarm: 3 Color (Green/Amber/Red)
Factory Reset 1EA (Push Button Switch)
Operational Temperature -30 to 55°C without solar load
Humidity 5-100 % RH, condensing, not to exceed 30 g/m3 absolute humidity
IP rating IP65
EMC FCC Part 15 Subpart B
FCC FCC Part 30 (5G RF)
Installation Pole/Wall mounting bracket
Dimension (W × D × H)
6.77 in.(172 mm) × 2.08 in.(53 mm) × 10.19 in.(259 mm)
Volume < 2.5 L (main frame, excluding bracket)
Weight < 4.4 lb (2.0 kg) (main frame, excluding bracket)
Power Consumption Typical 25 W, a maximum of 35 W

Confidential
Chapter 1 Before Installation
5G CPE Outdoor Installation Manual v1.0 5
Copyright © 2018, All Rights Reserved.
Cautions for Installation
Observe the safety instructions described in this section when installing the
system. Installation must be done in accordance with the applicable local electric
codes.
Before Installing
•Post warning signs in areas where high-voltage cables are installed.
•Post ‘off limit’ signs in areas where accidents are most expected.
•Use guardrails or fences to block open areas such as ditches, open roof areas,
and scaffolds.
Install the system in the restricted access area.
Use the power supplies that meets LPS.
While Installing
The system power must be cut off before installing.
Ensure the power switch of power supply is off when installing the system.
Installing the system with power switch on may cause system damage or fatal
human injury when connecting or disconnecting cables.
Ensure that workers wear protection gloves and goggles to prevent injury from
debris while drilling holes in a wall or ceiling.
Do not wear accessories such as watches and rings to prevent electrical shock.
Cover unused ports with a cap. This prevents foreign substances from entering into
the unused ports.
To prevent foreign substances, outdoor air, and moisture from entering the cable
inlet (including cable gland and conduit), finish the inlet as follows:
Unused inlet: Use the hole finishing materials including cap and rubber packing.
Cable-installed inlet: After cable installation, block any space in the inlet with
tape, compressed sponge, rubber packing, and silicone.

Confidential
Chapter 1 Before Installation
5G CPE Outdoor Installation Manual v1.0 6
Copyright © 2018, All Rights Reserved.
After Installing
Remove any debris produced during the work and clean up the installation site.
In the system, the laser beam light runs through the optical cable. The workers
must handle the optical cables with care as the laser beam can seriously damage
the eyes.
Ensure that the workers do not damage installed cables while cleaning the system.
While cleaning the power supply device, take precaution that the device does not
come in contact with foreign objects that may cause power failure.

Confidential
Chapter 1 Before Installation
5G CPE Outdoor Installation Manual v1.0 7
Copyright © 2018, All Rights Reserved.
Installation Tools
The table below lists the basic tools needed for installation. The additional tools
required for each site need to be identified and arranged during a site survey before
starting the installation.
Table 2. Basic Installation Tools
Number
Name
Specification
Purpose of use
1 Torque Driver Apply a torque range
: 2-10 lbf·in For fastening M3 Screw
Apply a torque range
: 20-90 lbf·in
For fastening M6 SEMS (Hexagon+)
2 Screw Driver Bit +, Number 2 For fastening M3 Screw
+, Number 3 For fastening M6 SEMS (Hexagon+)
3 Screw Driver +, Number 2 For loosening M3 Screw
+, Number 3 For loosening M6 SEMS (Hexagon+)
T25H For loosening M5 SEMS
4
T25H For fastening Torx Screw (T25H)
5 Torque Wrench
Apply a torque range
: 10-50 lbf·in For fastening Cable Gland Nut
6 Torque Wrench Spanner
Head
Apply Hexagon Head: 42 mm
(for 10~50 lbf·in) For fastening Cable Gland Nut
7 Spanner
42 mm For loosening Cable Gland Nut
8 Tape Measure
16 ft./150 ft. Tape measure for length
measurement
9
Power Extension Cable
100 ft.
Basic tool
10 Level
Normal For horizontality and verticality
11 Hammer Drill
Normal Wall type drilling

Confidential
Chapter 1 Before Installation
5G CPE Outdoor Installation Manual v1.0 8
Copyright © 2018, All Rights Reserved.
Number
Name
Specification
Purpose of use
12 Concrete Drill Bit
1/4 in. (6 mm) For Plastic Anchor
13 Cable Cutter
0.24-1.26 in. (6-32 mm) Cable cutting
14 Crimping Tool
14 AWG-4 AWG (1.5-16 mm2) Pressure terminal for crimping
15 Cable Stripper Apply cable thickness: 1.5-6.2
in. (4-16 mm) Cable sheath for removal
16 Nipper
Basic Tool For cutting cable
17 LAN Tool
Basic Tool RJ45 crimper
18 Industrial Scissor
Basic Tool Cutting
19 Knife
Basic Tool Cutting
20 Multi tester
Digital Pocket Tester To measure voltage and current to
detect cable disconnection
21 Compass
Normal Check azimuth during installation
22 Heating Gun
50-300°C Shrinking Heat Shrink Tube
The required installation tools may vary depending on the site conditions.
In addition to the basic tools, protractor, ladder, safety equipment, and cleaning
tools must also be arranged, considering the site conditions.