Samsung AR36BSHUMGMNCV User manual

AIR CONDITIONER CONTENTS
SYSTEM AIR CONDITIONER
SINGLE for North America (R-410A, Heat Pump)
1. Precautions
2. Product Speciѣcations
3. Disassembly and Reassembly
4. Troubleshooting
5. PCB Diagram and Parts List
6. Wiring Diagram
7. Reference Sheet
INDOOR UNIT OUTDOOR UNIT
AR36BSHUMGMNCV AR36BSHUMGMXCV

Contents
1. Precautions...................................................................................................................1-1
1-1. Precautions for the Service.............................................................................................................................. 1-1
1-2. Precautions for the Static Electricity and PL................................................................................................ 1-1
1-3. Precautions for the Safety............................................................................................................................... 1-1
1-4. Precautions for Handling Refrigerant for Air Conditioner........................................................................1-2
1-5. Precautions for Welding the Air Conditioner Pipe......................................................................................1-2
1-6. Precautions for Additional Supplement of Air Conditioner Refrigerant................................................1-2
1-7. Other Precautions..............................................................................................................................................1-2
2. Product Specifications................................................................................................ 2-1
2-1. Product Specifications......................................................................................................................................2-1
2-2. Specifications of optional items.................................................................................................................... 2-2
2-2-1. Accessories......................................................................................................................................... 2-2
3. Disassembly and Reassembly.................................................................................... 3-1
4. Troubleshooting ......................................................................................................... 4-1
4-1. Setting an indoor unit address and installation option ............................................................................ 4-1
4-1-1. The procedure of setting option...................................................................................................... 4-1
4-1-2. The procedure of setting option .....................................................................................................4-2
4-1-3. Order for Setting Options (Wired Remote Controller) ...............................................................4-5
4-1-4. Setting the indoor unit addresses..................................................................................................4-6
4-1-5. Changing the addresses and options individually..................................................................... 4-8
4-2. Model-specific option code............................................................................................................................4-9
4-3. Diagnostic Checklist...................................................................................................................................... 4-10
4-3-1. Test operation mode and check mode ........................................................................................4-10
4-3-2. Error code [indoor] ......................................................................................................................... 4-11
4-4. Troubleshooting by symptoms................................................................................................................... 4-12
4-4-1. Indoor temperature sensor error (E121)...................................................................................... 4-12
4-4-2. Indoor heat exchanger temperature sensor error (E122)........................................................4-13
4-4-3. Indoor unit float sensor error (E153) ...........................................................................................4-14
4-4-4. Indoor Fan error (E154).................................................................................................................. 4-15
4-4-5. EEPROM circuit failure (E162).......................................................................................................4-16
4-4-6. Communication error after finishing Tracking (E202)............................................................. 4-17
4-4-7. When the outdoor unit power is not ON - Initial Diagnosis : 1-phase products .................4-18
4-4-8. Indoor/outdoor communication error (1min.) (Error Code : E202)....................................... 4-20
4-4-9. Communication error between outdoor unit INV ᆎMAIN MICOM (1 min.)
(Error Code: E203)..........................................................................................................................4-22
4-4-10. Outdoor sensor error(Error Code : E221, E231, E251, E320) ................................................. 4-23
4-4-11. Compressor down due to freezing control (Error Code : E403)........................................... 4-24
4-4-12. Pipe blockage error (Error Code : E422)....................................................................................4-25
4-4-13. Outdoor unit Fan error (Error Code : E458, E475) .................................................................. 4-26
4-4-14. Compressor starting error / rotation error (Error Code : E461, E467).................................4-27
4-4-15. Full current error / PFC over-current error (Error Code : E462, E484)............................... 4-29
4-4-16. IPM (Over Current) error (Error Code : E464).......................................................................... 4-30
4-4-17. DC LINK over-current / low-voltage error (Error Code : E466)
H/W DC_Link Over Voltage Error (Error Code : E483)
AC Input Voltage Sensor Error (Error Code : E488)............................................................... 4-33
4-4-18. Gas leakage error (Error Code : E554)...................................................................................... 4-34
4-4-19. Others ............................................................................................................................................ 4-36

Contents
5. PCB Diagram and Parts List........................................................................................ 5-1
5-1. Indoor Unit Main PBA ...................................................................................................................................... 5-1
5-2. Indoor Unit Sub PBA........................................................................................................................................ 5-3
5-3. Outdoor Unit Main PBA .................................................................................................................................. 5-4
5-4. Outdoor Unit inverter PBA............................................................................................................................. 5-6
5-5. Outdoor Unit EMI PBA..................................................................................................................................... 5-7
6. Wiring Diagram........................................................................................................... 6-1
6-1. Indoor Unit......................................................................................................................................................... 6-1
6-2. Outdoor unit...................................................................................................................................................... 6-2
7. Reference Sheet...........................................................................................................7-1
7-1. Index for Model Name ......................................................................................................................................7-1
7-1-1. Indoor Unit........................................................................................................................................... 7-1
7-2. Refrigerating Cycle Diagram ......................................................................................................................... 7-2

Samsung Electronics 1-1
1. Precautions
1-1. Precautions for the Service
㽙 Use the correct parts when changing the electric parts.
– Please check the labels and notices for the model name, proper voltage, and proper current for the electric parts.
㽙Fully repair the connection for the types of harness when repairing the product after breakdown.
– A faulty connection can cause irregular noise and problems.
㽙When disassembling or assembling, make sure that the product is laid down on a work cloth.
– Doing so will prevent scratching to the exterior of the rear side of the product.
㽙Completely remove dust or foreign substances on the housing, connection, and inspection parts when performing repairs.
– This can prevent fire hazards for tracking, short, etc.
㽙Please tighten the service valve of the outdoor unit and the valve cap of the charging valve as securely as possible by using
a monkey spanner.
㽙Check whether the parts are properly and securely assembled after performing repairs.
– These parts should be in the same condition as before the repair.
1-2. Precautions for the Static Electricity and PL
㽙Please carefully handle the PCB power terminal during repair and measurement when it is turned on since it is vulnerable
to static electricity.
– Please wear insulation gloves before performing PCB repair and measurement.
㽙Check if the place of installation is at least 2m away from electronic appliances such as TV, video players, and stereos.
– This can cause irregular noise or degrade the picture quality.
㽙Please make sure the customer does not directly repair the product.
– Arbitrary dismantling may result in electric shock or fire.
1-3. Precautions for the Safety
㽙Do not pull or touch the power plug or the subsidiary power switch with wet hands.
– This may result in electric shock or fire.
㽙If the power line or the power plug is damaged, then it must be changed since this is a hazard.
㽙Do not bend the wire too much or position it so that it can be damaged by a heavy object on top.
– This may result in electric shock or fire.
㽙The use of multiple electric outlets should be prohibited.
– This may result in electric shock or fire.
㽙Ground the connection if it is necessary.
– The connection must be grounded if there is any risk of electrical short due to water or moisture.
㽙Unplug the power or turn off the subsidiary power switch when changing or repairing electrical parts.
– Doing so will prevent electric shock.
㽙Explain to workers that the battery for the remote control needs to be separated for storage purposes when the product
will not be used for a long time.
– This can cause a problem for the remote control since battery fluid may trickle out.

Precautions
1-2 Samsung Electronics
1-4. Precautions for Handling Refrigerant for Air Conditioner
Environmental Cautions: Air pollution due to gas release
㽙Safety Cautions
If liquid gas is released, then body parts that come into contact with it may experience frostbite/blister/numbness.
If a large amount of gas is released, then suffocation may occur due to lack of oxygen. If the released gas is heated, then noxious
gas may be produced by combustion.
㽙Container Handling Cautions
Do not subject container to physical shock or overheating. (Flowage is possible while moving within the regulated pressure.)
1-5. Precautions for Welding the Air Conditioner Pipe
㽙Dangerous or flammable objects around the pipe must be removed before the welding.
㽙If the refrigerant is kept inside the product or the pipe, then remove the refrigerant prior to welding.
If the welding is carried out while the refrigerant is kept inside, the welding cannot be properly performed. This will also produce
noxious gas that is a health hazard. This leakage will also explode with the refrigerant and oil due to an increase in the refrigerant
pressure, posing a danger to workers.
㽙Please remove the oxide produced inside the pipe during the welding with nitrogen gas.
Using another gas may cause harm to the product or others.
1-6. Precautions for Additional Supplement of Air Conditioner Refrigerant
㽙Precisely calculate the refrigerant by using a scale and S-net, and proceed with the test operation.
Excessive supplement can cause harm to the product since it can cause an inflow of the liquid refrigerant into the compressor.
㽙Do not heat the refrigerant container for a forced injection.
This may cause harm to the product or others since the refrigerant container may burst.
㽙Do not operate the product after removing the product safety pressure switch and sensor.
If the product is blocked inside, then this may cause harm to the product or others due to the excess pressure increase of the
refrigerant gas.
1-7. Other Precautions
㽙There should be no leakage of the pipes after installation. When withdrawing the refrigerant, the compressor should be
stopped before removing the connecting pipe.
If the compressor is operating while the refrigerant pipe is not correctly connected and the service valve is opened, then
air and other substances can enter the pipe. The interior of the refrigerant cycle may then build up excessive high pressure
resulting in explosion and damage.
㽙If the Wall Mounted type(Wind free) indoor unit is included in the installation combination, please contact us before
changing the Capacity correction for heating function to 33kg/cm2g during Outdoor unit key function setting.

Samsung Electronics 2-1
Item
CRAC
IN AR36BSHUMGMNCV
OUT AR36BSHUMGMXCV
Design
Indoor Unit
Outdoor Unit
Remote Controller
Performance Cooling [Btu/h] 9,500/36,000/39,000
Heating [Btu/h] 9,500/40,000/47,000
Power Consumption Cooling [W] 900/3,790/4,300
Heating [W] 560/4,510/5,820
EER/COP Cooling [Btu/hW] 9.5
Heating [Btu/hW] 8.85
Voltage / Frequency 1,2,208-230,60
Operating Current Cooling [A] 5.0/16.8/19.1
Heating [A] 3.0/20.0/24.0
Sound Pressure Indoor Unit [dBA] (H/M/L/Silence) 51/48/46/38
Outdoor Unit [dBA] (C/H) 52/54
Sound Power Indoor Uint [dBA] (Cooling) 65
Outdoor Uint [dBA] (Cooling) 69
Size
Net Dimension
(WxHxD)
Indoor Unit [mm] 1,280 x 253 x 345
Outdoor Unit [mm] 940 x 1,210 x 330
Shipping Dimension
(WxHxD)
Indoor Unit [mm] 1,352 x 326 x 420
Outdoor Unit [mm] 995 x 1,388 x 426
Weight
Net Indoor Unit [kg] 18.5
Outdoor Unit [kg] 86.0
Gross Indoor Unit [kg] 22.0
Outdoor Unit [kg] 95.5
Harness Specifications
Indoor Fan Motor DB31-00332C
Compressor UG5TK1450FJXSG
Outdoor Fan Motor DB31-00579A
Piping High Pressure עߪࢋߦߣ
Low Pressure עߢߦࢋߩߩ
Refrigerant Type R-410A
Factory Charging [g] 2,900
Additional Refrigerant (Over 5m, for every 5m) [g] 30
Basic Piping Length [m] 7.5
Max. Piping Length [m] 75
Max. Level Difference [m] 30
Option Code
0113FF-194593-276975-371700
020010-100000-200000-300000
030000-100000-200000-300000
050000-100000-200000-300000
2. Product Specifications
2-1. Product Specifications

2-2 Samsung Electronics
2-2-1. Accessories
ŵߤߧ9Ɗ²ƸđđĘAǤ
Item Description AͱʒʪĘͱࢋ Q’ty ŵʪɇθ
ŵߤߧ9Ɗ²ƸđđĘAǤ
ASSY WIRELESS
REMOCON DB96-24901P 1
Indoor Unit
BATTERY-MN 4301-000121 2
MANUAL USERS DB68-11577A 1
MANUAL INSTALL DB68-11578A 1
HOLDER-REMOCON DB61-06087A 1
SCREW-TAPPING(M4*L12) 6002-000213 2
CARD WARRNATY 6801-002246 1
2-2. Specifications of optional items

Samsung Electronics 2-3
Accessories (cont.)
ŵߤߧ9Ɗ²ƸđđǹAǤ
Item Description AͱʒʪĘͱࢋ
Q’ty
ŵʪɇθ
ŵߤߧ9Ɗ²ƸđđǹAǤ
MANUAL INSTALL DB68-11579A 1
Outdoor Unit
RUBBER-LEG DB73-20134A 4
SEAL DRAIN DB63-10355C 3
DRAIN-PLUG OUT DB67-00806A 1

Samsung Electronics 3-1
Item Remarks
+SCREW DRIVER
Adjustable Wrench
(8mm, 10mm, 13mm)
M6, M8 Hex Wrench
Necessary Tools
3. Disassembly and Reassembly

Disassembly and Reassembly
3-2 Samsung Electronics
ŵA࣍đǹ࣎ࡠŵߤߧ9Ɗ²ƸđđĘAǤ
No Parts Procedure Remark
1 Panel-Front 1) Stop the driving of air conditioner and
shut off main power supply.
2) Open the FRONT-GRILLE and pull out
from the PANEL-FRONT.
3) Detach COVER-TERMINAL from the
PANEL FRONT. (use + Screw Driver)
4) Loosen connector wire(white) and
detach the temperature sensor wire.
5) To detach the FRONT-PANELthe main
frame, unfasten 2 screw at the bottom.
(use + Screw Driver )
6) Take off the FRONT-PANEL,lifting up the
bottom

Disassembly and Reassembly
Samsung Electronics 3-3
No Parts Procedure Remark
2 TRAY DRAIN 1) Loosen stepping motor wire and
detach the hook of main frame.
2) To detach TRAY-DRAIN from the main
frame, pull the bottom of the TRAY-
DRAIN towards you.
3) To detach TRAY-DRAIN from the main
frame , pull the bottom of the TRAY-
DRAIN towards you.
.3 CONTROL IN 1) Unfasten the earth screw.
(use + ScrewDriver)
2) Detach the temperature sensor and
Humidity sensor.
3) Detach the temperature sensor.

Disassembly and Reassembly
3-4 Samsung Electronics
No Parts Procedure Remark
.3 CONTROL IN 4) Loosen MOTOR wires(white).
5) Take off the CASE-CONTROL from the
main frame. (use + Screw Driver)
4 PBA 1) Loosen the STEP UP/DOWN connector
(CN802).
AɇЇtion
When you separate the connector,
pull pressing the locking button.
2) Loosen the FUSE CHK connector
(CN140).
AɇЇϩͱ
When you separate the connector,
pull pressing the locking button.

Disassembly and Reassembly
Samsung Electronics 3-5
No Parts Procedure Remark
4PBA
3) Loosen the EVA IN/OUT connector. (CN403)
AɇЇϩͱ
When you separate the connector,
pull pressing the locking button.
4) Loosen the Humidity sensor connector
(CN401).
ĮΧϩͱʀͱʪʀϩͱθࢋ
AɇЇϩͱ
The terminal is locking type.
So, when you separate terminals, pull
pressing the button.
5) Loosen the DISPLAY connector.
(CN501).
AɇЇϩͱ
The terminal is locking type.
So, when you separate terminals, pull
pressing the button.
6) Loosen the POWER connector.
AɇЇϩͱ
When you separate the connector,
pull pressing the locking button.

Disassembly and Reassembly
3-6 Samsung Electronics
No Parts Procedure Remark
4PBA
7) Loosen the COMM wire connector (CN303).
AɇЇϩͱ
When you take off the PBA, don’t
touch the components.
Please hold the PBA both side.
8) Loosen the Motor connector(CN701).
AɇЇϩͱ
When you separate the connector,
pull pressing the locking button.
9) Take off the main PBA from the ASS’Y
Control in.
AɇЇϩͱ
When you take off the PBA, don’t
touch the components.
Please hold the PBA both side.
5 EVAPORATOR 1) Unfasten the screw at the right side.
(use + ScrewDriver)

Disassembly and Reassembly
Samsung Electronics 3-7
No Parts Procedure Remark
5 EVAPORATOR 2) Unfasten the screw at the left side.
(use + ScrewDriver)
3) Detach the HOLDER PIPE.
(use + Screw Driver)
4) Detach the BRACKET-EVAP.
(use + Screw Driver)
5) Detach the HOLDER EVAP.
(use + Screw Driver)
6) Loosen 1 fixing earth screw right side.
(use + Screw Driver)

Disassembly and Reassembly
3-8 Samsung Electronics
No Parts Procedure Remark
6FANMOTOR
&
CROSS FAN
1) Loosen 6 fixing screws of HOLDER-
MOTOR
2) unfasten the screw a little.
(use + Screw Driver)
3) unfasten the screw a little and pull the
MOTOR FAN to the right side.
(use + Screw Driver)
4) Loosen 1 fixing screws of HOLDER-FAN.
(use + Screw Driver)
5) unfasten the screw a little.
(use + Screw Driver)

Disassembly and Reassembly
Samsung Electronics 3-9
No. Parts Procedure Remark
1
Cabinet Front RH
Turn off the power before disassem-
bly necessarily.
1) Remove the 2 screws from the
Cabinet Front RH and separate it.
(Use + Screw Driver)
2 Cabinet Upper 1) Remove the 9 screws which is fixed
to each side of Cabinet Upper and
separate it.(Use + Screw Driver)
3 Cabinet-Installation
Front Part
1) Remove the1 screw which is fixed to
Cabinet-Installation Front Part and
separate it.(Use + Screw Driver)
ŵߤߧ9Ɗ²ƸđđǹAǤ

Disassembly and Reassembly
3-10 Samsung Electronics
No. Parts Procedure Remark
4
Outdoor Unit Guard 1) Pull out the sensor from the Outdoor
Unit Guard and separate it.
2) Remove the 4 screws which is fixed
to Outdoor Unit Guard and separate
it. (Use + Screw Driver)
5 Cabinet Rear RH 1) Pull out the sensor from the Cabinet
Rear RH and separate it.
2) Remove the 4 screws which is fixed
to each side of Cabinet Rear RH and
separate it. (Use + Screw Driver)

Disassembly and Reassembly
Samsung Electronics 3-11
No. Parts Procedure Remark
6
Cabinet-Installation
Rear Part
1) Remove the1 screw from the
Cabinet-Installation Rear Part and
separate it.(Use +Screw Driver)
7 Cabinet Front LF 1) Remove the 9 screws from the
Cabinet Front LF and separate it. (Use
+Screw Driver)

Disassembly and Reassembly
3-12 Samsung Electronics
No. Parts Procedure Remark
7
Cabinet Front LF
8 Fan 1) Remove the 2 fixing nuts like the pic-
ture on the right side. (Use Hexagon
Wrench, Monkey Spanner, Hexagon
Socket)