Samsung AZ09F1KE User manual

OWNER’S
INSTRUCTIONS
AZ09F1KE
WINDOW-TYPE
ROOM AIR CONDITIONER
(Cool and Heat)
E R
DB68-02037A(1)

The following safety precautions must be taken when installing
and using your air conditioner.
Safety Precautions
1 The air conditioner must be plugged into its own specific power source, which must be
installed in compliance with national wiring, earthing and safety regulations.
Depending on national regulations and your specific installation, you may need to install:
◆ A circuit breaker
For further information on electrical requirements, contact a professional electrician.
This device must be installed according to the national electrical rules.
2 Make sure that the unit is correctly ventilated at all times;
do NOT place clothing or other materials over it.
4Do NOT insert anything between the air outlet blades, as the inner fan may be damaged
and you may be hurt. Particularly, keep children away from the unit.
5ALWAYS ensure that the power cable is in good condition.
Make sure that it is not walked on or damaged by items placed on or against it.
If the power cord is damaged in any way, it must be replaced by an approved
power cord available from the manufacturer or its service agent.
6Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact:
◆ An approved service center
◆ The outlet at which the air conditioner was purchased
7Do NOT place any obstacles in front of the unit.
3NEVER spill liquids of any kind into the unit.
Should this happen, unplug the unit and contact your installation specialist.
8The appliance is not intended for use by young children or infirm person without
supervision; young children should be supervised to ensure that they do not play with
the appliance.
The manufacturer do not take the responsibility of the accident happened
because the air conditioner is not fixed firmly or installed securely, during
installing or using the product. In case you have difficulty in installation,
you must ask for an installation specialist help. The accident will be hap-
pened in case of installing improperly.
CC
CA AU UT TI IO ON N
E-2

Contents
◆PREPARING YOUR AIR CONDITIONER
■Safety Precautions ......................................................................................... 2
■Air Conditioning Unit - Main Parts and Control Panel .................................... 4
■Getting Started ............................................................................................... 5
◆OPERATING YOUR AIR CONDITIONER
■Cooling Your Room ......................................................................................... 6
■Heating Your Room ......................................................................................... 7
■Airing Your Room ............................................................................................ 8
■Switching the Air Conditioner Off ................................................................... 8
■Adjusting the Air Flow Direction Horizontally ................................................. 9
■Adjusting the Air Flow Direction Vertically ...................................................... 9
◆RECOMMENDATIONS FOR USE
■Operating Recommendations ......................................................................... 10
■Temperature and Humidity Ranges ................................................................ 10
■Cleaning Your Air Conditioner ......................................................................... 11
■Solving Common Problems ............................................................................ 12
■Technical Specifications ................................................................................. 13
◆METHOD OFINSTALLATION ................................................................................. 14
E-3

Air Conditioning Unit - Main Parts and Control Panel
Outer air flow blades
(up/down orientation)
Air inlet (Inside)
Air filter
(The air filter is located in inside )
Ventilation lever
Power plug
(The type of power plug may
differ, depending on the local
power supply.)
Air Outlet
Air inlet (Outside)
Temperature
control dial
Operating mode
selection dial
Air flow blade swing switch
Inner air flow blades
(right/left orientation)
E-4
❄The design and shape are subject to
change according to the model.

Getting Started
You have just purchased a window-type room air conditioner and it has been installed
by your installation specialist.
Your Owner’s Instructions contain much valuable information on using your air conditioner.
Please take the time to read them as they will help you take full advantage of the unit’s features.
The booklet is organised as follows.
◆The illustration on page 4 shows the air conditioning unit;
it indicates the location and purpose of the main parts and controls on the unit.
◆ In the main part of the document, you will find a series of step-by-step
procedures for each function available.
The illustrations in the step-by-step procedures use four different symbols:
PRESS PUSH IMPORTANT NOTE
☛
➢
E-5

Select the operating mode and fan speed.
To cool your room with a... Set the operating mode
selection dial to...
High fan speed HI COOL
Low fan speed LOW COOL
Result: ◆ The air conditioner starts up in Cool mode.
◆ The fan starts up at the speed selected.
You can change modes at any time.
CoolingYour Room
You must select the Cool mode if you wish to lower the temperature
in your room. You can also set the fan speed.
1
2
To control the direction of the air flow, refer to page 9.
3
To adjust the temperature, turn the temperature control dial towards
the right and the blue position.
Possible temperatures: Between 18°C and 25°C inclusive.
Result: The air conditioner starts cooling if the room temperature
is higher than the selected temperature.
29˚C
~ 27˚C
27˚C ~ 23˚C
23˚C
~ 18˚C
➢
E-6

Select the operating mode and fan speed.
To heat your room with a... Set the operating mode
selection dial to...
High fan speed HI HEAT
Low fan speed LOW HEAT
Result: ◆ The air conditioner starts up in Heat mode.
◆ The fan starts up at the speed selected.
You can change modes at any time.
You must select the Heat mode if you wish to heat your room
to a specific temperature. You can also select the fan speed.
To adjust the temperature, turn the temperature control dial towards
the left and the red position.
Possible temperatures: Between 25°C and 29°C inclusive.
Result: The air conditioner starts heating if the room temperature
is lower than the selected temperature.
2
To control the direction of the air flow, refer to page 9.
3
HeatingYour Room
1
29˚C
~ 27˚C
27˚C ~ 23˚C
23˚C
~ 18˚C
➢
E-7

To switch the unit off, simply set the operating mode selection dial
to the OFF position.
Result: The air conditioner stops operating.
AiringYour Room
Switching the Air Conditioner Off
If the atmosphere in your room is stale, you can air it using
the Fan feature and if necessary, evacuate the stale air outside.
You can switch the air conditioner off whenever you want.
1
Set the operating mode selection dial to the FAN position.
Both fan settings (left and right) have the same function.
Result: The air conditioner starts up in Fan mode.
2
To control the direction of the air flow, refer to page 9.
3
➢
If you wish to evacuate stale air outside, pull the ventilation lever on the front
of the unit and the open position ( ).
Result:
The air inside the room circulates and stale air is evacuated outside.
Otherwise, push the ventilation lever and the closed position ( ).
Result: The air simply circulates inside the room.
Open
Position Closed Position
E-8

Adjusting the Air Flow Direction Horizontally
Adjusting the Air Flow Direction Vertically
Depending on the position of the unit in your room, you can adjust the
orientation of the inner air flow blades on the right-hand side of the
unit, thus increasing the efficiency of the air conditioner.
1
To stop the blades moving left and right, set the air flow blade swing switch
to the position.
To stop the blades in a specific position and orient the air flow in the
corresponding direction, simply set the switch to the position
when the blades are in the required position.
2
Set the air flow blade swing switch to the position .
Result: The inner blades swing automatically left and right.
The blades may stop swinging momentarily when the Deice function
is activated (see page 10 for further details on this function).
They will start swinging again automatically as soon as the Deice
function stops.
Again depending on the position of the unit in your room, you can
adjust the orientation of the outer air flow blades on the right-hand
side of the unit.
RECOMMENDATION When...
Cooling
Heating
Adjust the blades to face...
Upwards.
Downwards.
Adjust the air flow blades to the required position, by pushing them
upwards or downwards.
If you orient the air flow blades downwards and the unit operates
in Cool mode for a long period of time, dew may:
◆ Form on the surface of the blades
◆ Drip from the blades
➢
➢
➢
E-9

Here are a few recommendations that you should follow when using
your air conditioner.
Topic Recommendation
The heat pump inside the air conditioner absorbs heat from
outside air and brings it indoors. If the temperature of the outside
air drops, the air conditioner will heat less.If you find that the room
is not warm enough, use an additional heating appliance.
Heating
performances
The air conditioner circulates warm air to heat your room;
as a result, some time will be required after starting
the air conditioner to warm the entire room. If necessary,
set the air conditioner going a short time before you wish
to use the room.
Warm air
circulation
When outside temperatures are low and humidity is high,
frost may form in the unit’s condenser when heating with your
air conditioner.
If this happens:
◆ The unit stops heating
◆ The air flow blades stop swinging
◆ The Deice mode is triggered automatically for about
five minutes.
No intervention is required from you; after about five minutes,
the air conditioner starts operating again normally.
Frost
If both the indoor and outdoor temperatures are high and you
select the Heat mode, the fan and compressor in the unit may
stop at times.This is normal; simply wait until the air conditioner
switches on again.
High indoor
and outdoor
temperatures
If a power failure occurs when the air conditioner is operating,
the unit is switched off. When the power returns,
the air conditioner starts up again automatically.
Power failure
Temperature and Humidity Ranges
Operating Recommendations
E-10
If the air conditioner is used at... Then...
Higher temperature The automatic protection feature may be triggered
and the air conditioner stopped.
Lower temperature A water leakage or some other malfunction may happen
if the heat exchanger freezes.
Higher humidity levels Water may condense on and drip from the surface of the unit
if it is used for long periods.
The following table indicates the temperature and humidity ranges,
within which the air conditioner can be used.
Mode Indoor
Temperatures Outdoor Temperature Indoor Humidity
Heating
Cooling
28°C or less
21°C to 32°C approx.
0°C to 21°C approx.
21°C to 43°C approx.
-
80% or less