Samsung MH020FPEA User manual

INSTALLATION MANUAL
MANUAL DE INSTALACIÓN
MANUEL D’INSTALLATION
MANUALE D’INSTALLZIONE
MANUAL DE INSTALAÇÃO
INSTALLATIONS-HANDBUCH
INSTALLATION MANUAL
INSTALLATION MANUAL
Free Joint Multi Air Conditioner (Cool and Heat)
Acondicionador de aire libre del empalme multi (Refrigeración y Calefacción)
Climatiseur Free Joint Multi (Refroidissement et Chauffage)
Aria condizionata Free Joint Multi (Raffreddamento e Riscaldamento)
Free Joint Multi ar condicionado (Refrigeração e Aquecimento)
Free Joint Multi Klimaanlage (Kühlen und Wärmen)
Free Joint Multi Air Conditioner (Cool and Heat)
Free Joint Multi Air Conditioner (Cool and Heat)
ENGLISH
ESPAÑOL
FRANÇAIS
ITALIANO
PORTUGUÊS
DEUTSCH
E§§HNIKA
RUSSIAN
MH020FPEA
MH023FPEA
MH026FPEA
MH035FPEA
MH052FPEA
MH18VP2-09
MH19VP2-07
MH19VP2-12
E S F I P D G R DB98-20238A(2)
MH026FPEA IM_E_20238 1/24/05 5:25 PM Page 17

E-2
Safety Precautions
The following safety precautions must be taken when using your air conditioner.
◆The unit should not be installed by the user. Ask the dealer or authorized
company to install the units except room air conditioners for the U.S.A and
Canada area.
◆If the unit is installed improperly, water leakage, electric shock or fire may
result.
◆The air conditioner must be installed in accordance with national wiring
regulations and safety regulations wherever applicable.
◆Mount with the lowest moving parts at least 2.5m above the floor or grade
level. (If applicable)
◆The manufacturer does not assume responsibility for accidents or injury
caused by an incorrectly installed air conditioner. If you are unsure about
installation, contact an installation specialist.
◆When installing the built-in type air conditioner, keep all electrical cables
such as the power cable and the connection cord in pipe, ducts, cable
channels e.t.c to protect them against liquids, outside impacts and so on.
WARNING
INSTALLING THE UNIT
◆If the power cord of this air conditioner is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
◆The unit must be plugged into an independent circuit if applicable or
connect the power cable to the auxiliary circuit breaker. An all pole
disconnection from the power supply must be incorporated in the fixed
wiring with a contact opening of >3mm.
◆Do not use an extension cord with this product.
◆If the unit is equipped with a power supply cord and a plug, the plug must
be accessible after installation.
◆This appliance must be installed accordance with the national wiring
regulations.
POWER SUPPLY LINE,
FUSE OR CIRCUIT
BREAKER
Risk of electric shock. • Can cause injury or death. • Disconnect all
remote electric power supplies before servicing, installing or cleaning.
• This must be done by the manufacturer or its service agent or a similar
qualified person in order to avoid a hazard.
MH026FPEA IM_E_20238 1/24/05 5:25 PM Page 2

E-3
ENGLISH
Contents
◆PREPARING THE INSTALLATION
■Deciding on Where to Install the Air Conditioner ......................................... 4
■Air Conditioner and Accessories .................................................................. 7
◆INSTALLING THE INDOOR UNIT
■Fixing the Installation Plate .......................................................................... 8
■Purging the Unit ........................................................................................... 8
■Connecting the Assembly Cable .................................................................. 9
■Installing and Connecting the Indoor Unit Drain Hose ................................. 10
■Installing and Connecting the Indoor Unit Assembly Piping ........................ 11
■Cutting/Extending the Piping ........................................................................ 12
■Placing the Indoor Unit in Position ............................................................... 13
■Assigning Address to Indoor Unit ................................................................. 13
■Additional Functions ..................................................................................... 13
◆COMPLETING THE INSTALLATION
■Wiring Wired Remote Controller (Optional) ................................................. 14
■Troubleshooting ............................................................................................ 15
■Explaining Operations to the Owner ............................................................ 15
MH026FPEA IM_E_20238 1/24/05 5:25 PM Page 3

E-4
Deciding on Where to Install the Air Conditioner
When deciding on the location of the air conditioner with the owner, the following restrictions
must be taken into account.
General
Do NOT install the air conditioner in a location where it will come into contact with the following elements:
◆Combustible gases
◆Saline air
◆Machine oil
◆Sulphide gas
◆Special environmental conditions
If you must install the unit in such conditions, first consult your dealer.
Indoor Unit
◆There must be no obstacles near the air inlet and outlet.
◆Install the indoor unit on a surface that can support its weight.
◆Choose a position that enables the piping and cables to be easily connected to the outdoor unit and the
recommended length of 5 metres to be respected.
◆Leave enough clearance beneath the indoor unit to enable the filters to be removed without hindrance.
◆Maintain sufficient clearance around the indoor unit, as indicated in the diagram on the page opposite.
◆Make sure that the water dripping from the drain hose runs away correctly and safely.
PREPARING THE INSTALLATION
◆You have just purchased a Free Joint Multi air conditioner and it has been installed by
your installation specialist.
◆This device must be installed according to the national electrical rules.
◆Max input power & current is measured according to IEC standard and input power &
current is measured according to ISO standard.
CC
CA AU UT TI IO ON N
MH026FPEA IM_E_20238 1/24/05 5:25 PM Page 4

E-5
ENGLISH
PREPARING THE INSTALLATION
1, 220-240, 50
Indoor unit Outdoor unit Power supply
Ø, V, Hz
✴✴ 020/026/035FP ✴✴
✴✴
026/035FK ✴✴
MH052FXEA2
✴✴ 18 ✴✴ MH18VP2X
✴✴ 19 ✴✴
MH19VP2X
✴✴ 20/26/35 ✴✴
Liquid
1/4”
Gas
3/8”
Unit Outside diameter
◗ Piping length and the height
Dimension
Composition
1 Room max
length
20 m
A, B
2 Room total max
length
40 m
A+B
Max height between
indoor units
3 m
(h)
Max height between
indoor unit & outdoor unit
15 m
(H)
160 mm
or more
100 mm
or more
200 mm
or more
300 mm
minimum
600 mm
minimum
600 mm
minimum
300 mm
minimum
Main power switch
(h) (H)
AB
◆ MH18VP2X / MH19VP2X / MH052FXEA2
◗ Piping outside diameter
MH026FPEA IM_E_20238 1/24/05 5:25 PM Page 5

Deciding on Where to Install the Air Conditioner (Continued)
PREPARING THE INSTALLATION
E-6
◆ MH068FXEA4 / MH080FXEA4◆ MH068FXEA4 / MH080FXEA4
1, 220-240, 50
Indoor unit Outdoor unit Power supply
Ø, V, Hz
✴✴23/26/35/52✴✴
MH068FXEA4
MH080FXEA4
✴✴23/26/35✴✴
✴✴52✴✴
Liquid
1/4”
1/4”
Gas
3/8”
1/2”
Unit Outside diameter
◗ Piping outside diameter
◗ Piping length and the height
Dimension
Composition
1 Room max
length
25 m
A, B, C, D
2 Room total max
length
30 m
A+B
3 Room total max
length
45 m
A + B + C
4 Room total max
length
70 m
A + B + C + D
Max height between
indoor units
3 m
(h)
Max height between
indoor unit & outdoor unit
15 m
(H)
160 mm
or more
100 mm
or more
200 mm
or more
300 mm
minimum
600 mm
minimum
600 mm
minimum
300 mm
minimum
Main power switch
AB CD
❊ The split type, 1-way cassette, duct type indoor units can be installed together.
(h) (H)
MH026FPEA IM_E_20238 1/24/05 5:25 PM Page 6

E-7
ENGLISH
E-7
Air Conditioner and Accessories
PREPARING THE INSTALLATION
The following accessories are supplied with the air conditioner.
Accessories in the Indoor Unit Case
OWNER'S INSTRUCTIONS
MANUAL DE INSTRUCCIONES
ISTRUZIONI PER L'USO
MANUAL DE INSTRUÇÕES
MANUEL D'UTILISATION
GEBRAUCHSANWEISUNG
GEBRAUCHSANWEISUNG
GEBRAUCHSANWEISUNG
Splut-typeRoom Air Conditioner
Aireacondicionado doméstico sistema Split
Condizionatored'aria per ambienti ad unità Separate
Aparelhode ar condicionado tipo Split
Climatiseurde type séparé
Geteilteraumklimaanlage
Geteilteraumklimaanlage
Owner’s Instruction
OWNER'S INSTRUCTIONS
MANUAL DE INSTRUCCIONES
ISTRUZIONI PER L'USO
MANUAL DE INSTRUÇÕES
MANUEL D'UTILISATION
GEBRAUCHSANWEISUNG
GEBRAUCHSANWEISUNG
GEBRAUCHSANWEISUNG
Splut-typeRoom Air Conditioner
Aireacondicionado doméstico sistema Split
Condizionatored'aria per ambienti ad unitàSeparate
Aparelhode ar condicionado tipo Split
Climatiseurde type séparé
Geteilteraumklimaanlage
Geteilteraumklimaanlage
Installation Manual
Batteries for
Remote Control (1)
Wired remote
Controller cables (1)
The following connection accessories may be supplied, depending on the option. If they are not
supplied, it is recommended that you collect them together before starting to install the air conditioner.
➢If these accessories are supplied, they are located in the accessory box.
Installation Plate (1)
(✴✴20/23/26/35✴✴)Installation Plate (1) (✴✴52✴✴)
Remote Control
Pipe Clamps B (3) M3.8 x 20 Screws
for Wood (6) Putty 100g (1)M4 x 16 Tapped Screws (6) Drain Hose, length 2m (1)
Pipe Clamps A (3)
Assembly Piping,
Ø6.35mm (1) Assembly Piping, Ø9.52mm (1)
(✴✴20/23/26/35✴✴)
Assembly Piping,
Ø12.70mm (1)
(✴✴52✴✴)
PE T3 Foam
Tube Insulation(1) Vinyl Tape, Width 50mm (1) Drain Plug (1) Rubber Leg (4)
MH026FPEA IM_E_20238 1/24/05 5:25 PM Page 7

E-8
Fixing the Installation Plate
INSTALLING THE INDOOR UNIT
19
100 158
30mm
Installation plate
Pipe hole
(
Ø 65mm)
(Unit : mm)
MH020FPEA/MH023FPEA/MH026FPEA/
MH18VP2-09/MH19VP2-07
45
90 165
(Unit : mm)
MH035FPEA/MH19VP2-12
MH052FPEA
45
512 415
(Unit : mm)
Before fixing the installation plate to a wall or window frame, you
must determine the position of the 65 mm hole through which the
cable, piping and hose pass to connect the indoor unit up to the
outdoor unit. When facing the air conditioner in position on the wall,
the piping and cable can be connected from the:
◆Right
◆Left
◆Rear (right or left)
◆Underside
1Determine the position of the pipe and drain hose hole using the right
figure and drill the hole with an inner diameter of 65 mm so that it slants
slightly downwards.
2 If you are fixing the indoor unit to a... Then follow Steps...
Wall 3.
Window frame 4to 6.
3Fix the installation plate to the wall in a manner appropriate to the weight
of the indoor unit.
➢If you are mounting the plate on a concrete wall with anchor
bolts, the anchor bolts must not project by more than 20 mm.
4Determine the positions of the wooden uprights to be attached to the
window frame.
5Attach the wooden uprights to the window frame in a manner appropriate
to the weight of the indoor unit.
6Using tapped screws, attach the installation plate to the wooden uprights,
as illustrated in the last figure opposite.
Purging the Unit
On delivery, the indoor unit is loaded with an inert gas. All this gas
must therefore be purged before connecting the assembly piping.
To purge the inert gas, proceed as follows.
Unscrew the caps at the end of each pipe.
Result: All inert gas escapes from the indoor unit.
➢To prevent dirt or foreign objects from getting into the pipes
during installation, do NOT remove the caps completely
until you are ready to connect the piping.
MH026FPEA IM_E_20238 1/24/05 5:25 PM Page 8

E-9
ENGLISH
Connecting the Assembly Cable
INSTALLING THE INDOOR UNIT
The indoor unit is powered from the outdoor unit via the assembly cable.
1Extend the assembly cable if necessary.
2Open the front grille by pulling on the tabs on the lower right and left sides
of the indoor unit.
3Remove the screw securing the connector cover.
4Pass the assembly cable through the rear of the indoor unit and connect the
assembly cable such as figure.
➢Each wire is labelled with the corresponding terminal number.
5Pass the other end of the cable through the 65 mm hole in the wall.
6Replace the connector cover, carefully tightening the screw.
7Close the front grille.
8For further details on how to plug the other end of the assembly cable into
the outdoor unit, refer to installation manual of the outdoor unit.
1(L) 2(N)
F1 F2
F12(N)1(L) F2
12E
E
12
F1 F2
F1 F2
Indoor
unit
Outdoor
unit
Earth
terminal
Earth
terminal
MH026FPEA IM_E_20238 1/24/05 5:25 PM Page 9

E-10
To install the drain hose, proceed as follows.
1If necessary, connect the 2-meter extension to the drain hose.
2If you are using the extension, insulate the inside part of the extension
drain hose with a shield.
3Pass the drain hose under the refrigerant piping, taking care to keep the
drain hose tight.
4Pass the drain hose through the hole in the wall, making sure that it is
sloping downwards, as shown in the illustrations above.
➢The hose will be fixed permanently into position once the
whole installation has been tested for gas leaks; refer to
installation manual of the outdoor unit.
Installing and Connecting the Indoor Unit Drain Hose
Care must be taken when installing the drain hose for the indoor unit to ensure that any condensation
water is correctly drained outside. When passing the drain hose through the 65 mm hole drilled in the
wall, check that none of the following situations occur.
The hose must
NOT slope
upwards.
The end of the drain
hose must NOT be
placed in water.
Do NOT bend the
hose in different
directions.
Keep a clearance of
at least 5 cm between
the end of the hose
and the ground.
Do NOT place the
end of the drain hose
in a hollow.
5 cm
less Ditch
INSTALLING THE INDOOR UNIT
Shield
Drain hose Extension drain hose
MH026FPEA IM_E_20238 1/24/05 5:25 PM Page 10