Samsung Galaxy S6 edge Assembly instructions

Galaxy S6
Glass/Lcd
REPAIR GUIDE
Version 1
2016 Edition

RiAna Soto
Repair Training Specialist
[email protected]
Samsung Galaxy 5s chargeport REPAIR
GUIDE

FOR EVERY REPAIR
MAKE SURE TO COMPLETE, INITIAL,
AND HAVE CUSTOMER SIGN THE CELLAIRIS
REPAIR LIABILITY WAIVER FORM

PRE-REPAIR DEVICE CHECK-IN

•Philips screwdriver
•Spudger
•Tweezers
•Isesamo
•Pentalobe screwdriver
•Magnetic Mat
•IPhone 5/5s replacement Chargeport
TOOLS NEEDED

•Always operate the heat gun on the lowest setting.
•Keep face, hands, hair, and clothing away from the air stream.
•The air nozzle also becomes extremely hot. Never grab the heat gun by the nozzle.
•Never operate the heat gun by laying it on its side on a table. It should be firmly grasped in one hand
at all times during usage.
•Never operate near flammable or explosive liquids and vapors. Cleaning supplies and the 3M #94
Primer are of concern. Make sure fumes are absent from the work area before operating the heat gun
•The heat gun nozzle should never get closer than 2“ to the object being heated.
•Keep heat gun moving. Never stay in one spot.
HEAT-GUN PRECAUTIONS

•Magnetic Pad: During the repair, you will be utilizing a magnetic pad to organize the plethora of
differing screws that you will be pulling out of the iPhone 6S. Below is a list of several internal
components of the iPhone 6S that should never be placed on the pad, or you risk damaging the
hardware or erasing client data:
•LCD/Digitizer Assembly
•Cameras
•Motherboard
•Battery
•Speaker
ADDITIONAL PRECAUTIONS

•Power on/off: To avoid any damage to the hardware during the repair, it is best to have the device
powered off until you can get to and disconnect the battery.
•Battery: Never unplug any flex cables unless the battery has been completely disconnected to avoid
frying your hardware. Do not plug the battery back until all cables have been reconnected.
•Release Screws: Apply pressure on the screw and twist counterclockwise to initially loosen it, then
lighten the pressure and continue twisting until the screw is gently released. Make sure you have
properly sized screwdrivers available for the repair.
•Pin Connectors: extremely fragile and must be plugged or unplugged with extreme caution.
•Battery connector: held down by light adhesive and solder. If not cautious it will come off the
motherboard. Very time consuming to be repaired. Do not break it in the first place.
•Motherboard: small surface mount components can be easily damaged if they are nicked by the
spudger. Always take your time and never touch the surface of the motherboard.
ADDITIONAL PRECAUTIONS

LET’S START!

STEP 1
•Power off device.
•Remove the bottom two (2) pentalobe screws using
the pentalobe screwdriver.
•Take the isesamo tool and slide it in between frame
of phone and bezel to open device. Keep in mind
the iPhone 5s has a home button flex cable attached
to the screen so this needs to be disconnected
before completely opening the screen.
Disassemble the device
Tools: Pentalobe screwdriver

STEP 2 •Once the home button flex cable is
disconnected screen will be lifted open.
•Disconnect the battery by removing
metal bracket covering battery cable and
disconnect.
•Next, disconnect the Digitizer/LCD and
proximity sensor cables to remove screen
by taking off the EMI shield held down by
four (4) Philips screws. Use spudger to
disconnect cables. We will be working
only with the back housing.
Disassemble the device
Tools: spudger, Philips
screwdriver

STEP 3
•Now that the screen is removed we will go back
down to the chargeport flex cable and
disconnect using the flat end of the spudger.
Bend cable back out of the way.
•Disconnect the antenna below battery connector
on board. Use spudger or plastic tweezers. BE
GENTLE!
Disassemble the device
Tips:
The chargeport, audio jack and
microphone are all one part that will be
taken out. Two things attached to
original part will be transferred to new
part.
Tools: spudger

STEP 4
•Remove standoff screw next
to antenna.
•Next we will remove the two
Philips screws at the bottom
of the loud speaker.
•At this point the loud speaker
will be able to come out. Use
flat in of spudger or your
finger to lift it up slightly then
pull the loud speaker to the
right then slide out
Disassemble the device
Tips: make sure to keep screws
organized on magnetic mat.
Tools: Spudger, fingers

STEP 5
•Remove the five (5) Philips screws and make sure to
keep them organized so you will be able to put
them back in the right places.
•Next, use the spudger to get underneath the
chargeport flex cable to lift up and out. It is held
down by adhesive but, once it’s lifted use your
fingers to pull it out.
Disassemble the device
Tools: spudger

STEP 6
•Now that the original part is removed underneath you will
notice a metal bracket and metal washer they sometimes will
come lose make sure to keep those in the device in the correct
position.
•The black rubber gasket covering the gold prong needs to be
transferred and metal bracket lining the audio jack needs to be
transferred if it isn’t already on replacement part. As well as the
bracket holding the cable that will be connected to the home
button flex connector( all pointed out in original picture).
Disassemble the device
Tools: spudger, tweezers
Original
New

STEP 1
•Those pieces are now transferred over so
put the new replacement part back into the
device.
•Start with the rubber black gasket slide that
into position and audio jack until you feel It
snap into position.
•Next, make sure the chargeport is slid all the
way in until you feel it snap into position.
Reassemble the device
Tip: peel blue or red covering
off adhesive so the new part
will stay in place.
Tools: Philips screwdriver,
spudger

STEP 2
•After positioned properly screw in the five (5)
Philip screws.
•Slide the loud speaker into the place by taking
the long end and slide it underneath the home
button flex connector and simultaneously get
the top of the loud speaker prong under the
motherboard.
•Then screw the bottom two (2) Philip screws into
the bottom of speaker.
•Then screw the standoff screw into place
(highlighted by blue circle).
Tips: take your time so
everything is fitting accordingly.
Tools: Philips screwdriver, spudger, Fingers

STEP 3
•Next, reconnect the antenna.
•Reconnect the chargeport flex cable.
•Next reconnect the Digitizer/LCD and proximity cable to assemble screen back. Screw the EMI shield back into
place.
Tips: take your time so
everything is fitting accordingly.
Tools: Philips screwdriver, spudger, Fingers

STEP 4
•Connect battery and put metal bracket back over battery and screw in the two (2) Philips screws.
•Reconnect home button flex cable and place metal bracket over connector, before closing the screen.
Tips: take your time so
everything is fitting accordingly.
Tools: Philips screwdriver, spudger, Fingers

STEP 5
•Final step is to screw the two (2) pentalobe
screws into the bottom of the phone with
the pentalobe screwdriver. At this point
power on device and run a post test to
check functionality and make any notes on
customer check-in device sheet.
•Do Post test actions.
Reassemble the device
Tools: Pentalobe screwdriver