Samsung SCH-6100 - Cell Phone - CDMA User manual

ELECTRONIC
SERVICE
CDMA PORTABLE
PCS TELEPHONE
SCH-6100
3
DEF
15
JKL
6
MNO
GHI
49
WXYZ
PQRS
70
2
ABC. '
CLR
MENU
OK
TALK
8
TUV
OPER
END
Next Space
Manual
CDMA PORTABLE PCS TELEPHONE CONTENTS
1.Specfication
2.NAM Programming
3.Test Procesure - Test command
4.Product Support Tool
5. ExplodedViews and Parts List
6. Electrical Parts List
7.Block Diagrams
8.PCB Diagrams
9.Schematic Diagrams

1.Specification
1-1General
FrequencyRange
Transmitter:1850 ¡- 1910 MHz
Receiver:1930 ¡- 1990 MHz
ChannelBandwidth:1.23 MHz
ChannelSpacing:50 KHz
NumberofChannels:1200
DuplexSeparation:80 MHz
TypeofEmission:G7W
Input/OutputImpedance :50 ohms
IntermediateFrequency
Transmitter:130.38 MHz
Receiver:210.38 MHz
LocalFrequency
Transmitter:1st(FTX-130.38),2nd(260.76MHz)
Receiver:1st(FRX-210.38),2nd(420.76MHz)
TCXOFrequency:19.68 MHz
FrequencyStability:(fRX -80MHz)¡¾ 150Hz
OperatingTemperature:-30¡É ¡- +60¡É
SupplyVoltage:+3.6V
CurrentConsumption
Standby:100mA(Non-slotmode)
Talk:320mA(at+10dBm)
Size(Inch)andWeight
includingSlimBattery:4.1(H) ¡¿ 1.8(W)¡¿ 0.7(D),86g
includingStandardBattery:4.1(H) ¡¿ 1.8(W)¡¿ 0.8(D),109g
includingExtendedBattery:4.1(H) ¡¿ 1.8(W)¡¿ 1.0(D),131g
CDMA Portable PCS Telephone 1-1

1-2Transmitter
Waveform Quality:0.944 or more
OpenLoop PowerControlRange
¡¤-25 dBm:-60.5dBm¡- -41.5dBm
¡¤-65 dBm:-20.5dBm¡- +1.5dBm
¡¤-104dBm:+15.0dBm¡- +30.0dBm
MinimumTXPowerControl:-50dBmbelow
ClosedLoop PowerControlRange:¡¾24dB
MaximumRFOutputPower:200mW(+23dBm)
OccupiedBandwidth:1.23MHz
ConductedSpuriousEmissions@1.25MHz:-42 dBc/30KHz
1-3Receiver
RX SensitivityandDynamicRange:-104dBm,FER=0.5%orless
:-25 dBm,FER=0.5%orless
ConductedSpuriousEmission
¡¤
1930 ¡- 1990 MHz:<-81dBm
¡¤
1850 ¡- 1910 MHz:<-61dBm
¡¤
All OtherFrequencies :<-47dBm
SingleToneDesensitization:lowerthan1%
RX power=-101dBm
Tonepower=-30dBm
Toneoffsetfromcarrier=¡¾1.25MHz
Intermodulation SpuriousResponse Attenuation:lowerthan1%
RX power=-101dBm
Tonepower1=-43dBm
Tonepower2=-43dBm
Tone1offsetfromcarrier=¡¾1.25MHz
Tone2offsetfromcarrier=¡¾2.05MHz
1-2 CDMA Portable PCS Telephone

2.NAMProgramming
NAMfeatures canbeprogrammedasfollows:
Notes:
-IfyouentertheNAMprogram mode,eachitemshowsthe currenlystored data.Goto
thenextitembypressing<OK/
••
>.
-Youcanmodifythedatabyenteringanewdata.
-Ifyouenterawrongdigit,press <CLR>todeletethelastdigit.Press andhold
<CLR>todeleteall digits.
-Toscroll itemsbackwardsorforwards,press theVOLUMEbuttonontheleftsideof
thephone.
2-1GeneralSetup
-------------------------------------------------------------------------------------------------------------------
LCD Display Key in Function
-------------------------------------------------------------------------------------------------------------------
MENU,8,2,0-selectsNAMprogramming
EnterLock??????
SVCMenu¡ç¡æ 2-choose'GENERAL'
1:Phone#
2:General
3:NAM
ESNVolume¡ã -ElectronicSerialNumberofthephoneisdisplayed.
B0000000
CAIversionVolume¡ã -CommonAirInterfaceversionisdisplayed
1
SCMVolume¡ã -StationClass Mark displaysthepowerclass,
01101010 transmission,slottedclass,dualmode.
LockCodeLockcode,currentstatusisdisplayed.
0000 4-digitcode-tochange,enternewcode.
OK/
••
-storesit
SlotModeSlotmode.'Yes'indicatestheslotmode.
Yes
¡ç ¡æ -changesthestatus.
or-storesit.
OK/
••
CDMA Portable PCS Telephone 2-1

SlotIndexSlotmodeindex.Thehigher,thelongersleepingtime
20-7-tochange,enternewone.
OK/
••
-storesit.
BrowserUpBrowserEnable
Yes
¡ç ¡æ -changesthestatus.
or-storesit.
OK/
••
2-2 SettingUpNAM1
-------------------------------------------------------------------------------------------------------------------
LCD Display Key in Function
-------------------------------------------------------------------------------------------------------------------
Svc Menu¡ç ¡æ Volume¡ã NAMProgrammingMenuisdisplayed
1:PCSPhone#
2:General
3:NAM
Svc Menu¡ç ¡æ 3choose'SetupNAM'
3:NAM
IMSI_MCC IMSIMobileCountryCode,currentcodeisdisplayed.
310 number-tochange,enternewone.
OK/
••
-storesit.
IMSI_MNC IMSIMobileNetworkCode,currentcodeisdisplayed.
00 number-tochange,enternewone.
OK/
••
-storesit.
CDMA ACCOLC CDMA Access OverloadClass,currentstatusisdisplayed.
0class number-tochange,enternewone.
OK/
••
-storesit.
CDMAHomeSIDCDMAHomesystemID,currentstatusisdisplayed
Yes¡ç ¡æ -storesit.
or.
OK/
••
CDMAfSIDCDMAforeign SID,currentstatusisdisplayed.
Yes
¡ç ¡æ
-changesthesystem.
or-storesit.
OK/
••
2-2 CDMA Portable PCS Telephone

CDMAfNIDCDMAforeignNID,currentstatusisdisplayed.
Yes
¡ç ¡æ
-changesthesystem.
OK/
••
-storesit.
HomeSIDfirstSIDwritteninthelist,currentstatusisdisplayed.
4120 number-tochange,enternewone.
OK/
••
-storesit.
NIDfirstNIDwritteninthelist,currentstatusisdisplayed.
65535 number-tochange,enternewone.
OK/
••
-storesit.
CDMA Portable PCS Telephone 2-3

3.TestProcesure-Testcommand
ListofEquipments
-DCPowerSupply
-TestJig
-TestCable
-CDMAMobileStationTestSetHP8924C,HP83236A,
CMD-80,etc
-SpectrumAnalyzer(includeCDMAtestmode) HP8596E
ConfigurationofTest
SpectrumAnalyzer
RF In
HP8924C
RF
In/Out
TestJig
DCPowerSupply
(+3.8 V)
Power
spliter
3-1 CDMA Portable PCS Telephone

ConfigurationofTest(Hands-Free)
DCPOWER
SUPPLY
(+13.7V)
+
-
HANDSFREE
KITBOX
DATAPWR
CRADLE
ANTENNA
Red
Orange
Black
CDMA Portable PCS Telephone 3-2

ITEMS SEC CODE REMARK
RFCableGH39-00007ACableLoss :2.1dB,1.9GHz
ConnectionbetweenPhoneandTestEquipment(Ex.8924C)
TESTINTERFACE
BOXGH80-00001AIncluding 1.PowerCable(Black,Red)
2.9-pinRS232 CableforPC.
DMCableGH39-30525AConnectionbetweenPhoneandPC
TESTCABLEGH39-00052AConnectionbetweenPhoneandDB25 connectorofINTERFACEBOX
Test Cable Connection Diagram
TEST INTERFACE BOX
TEST CABLE
Items needed to purchase from SAMSUNG
UP: AUTO POWER ON
DOWN: NOT USE
AUTO SELECT
LEFT: AUDIO IN
RIGHT: AUDIO OFF
DC POWER INPUT PORT
CHANGE VOLTAGE LEVEL
BY MODEL (3.8 VDC)
• RED: +
• BLACK: GND
DB9 CONNECTOR
CONNECT TO IBM PC
SERIAL PORT
RJ11 CONNECTOR
CONNECT TO HP
SERIAL PORT
DB25 CONNECTOR
CONNECT TO DB25 CONNECTOR OF
TEST INTERFACE BOX
I/F CONNECTOR
CONNECT TO HHP
NOT USED
CONNECT TO
AUDIO IN PORT OF
TEST EQUIPMENT
(USE BNC CABLE)
CONNECT TO
AUDIO OUT PORT OF
TEST EQUIPMENT
(USE BNC CABLE)
DB25 CONNECTOR
CONNECT TO DB25
CONNECTOR OF
TEST CABLE
TEST INTERFACE BOX
AUTO A-IN RED(+)
DC3.8V TO PC
TO HP
PROBETO A-INTO A-OUT
T
E
S
T
P
A
C
K
BLK(-)
3-3 CDMA Portable PCS Telephone

Test Mode
A.Tochangethephone's statefromNormalModetoTestMode,Youshouldenterthe
followingkeys.
"4 7 *869#1235"
B.Press thekeys"0 1"(Suspend)alwaysintheTestMode.
C.The command"2 0"ismodeandchannelchange,press <OK/
••
>tosave.
"30600"
Channel:600
Defaultvalue:3
D.TofinishtheTestMode,Youshouldenterthe command"0 2".
Channel Selection & Adjustment of the Transmit Power Level
A.EntertoTestMode.
B.Press thekeys¡° 0 1¡± (Suspend)alwaysintheTestMode.
E."090600#":Set to'0600'channel.
F."0 7":CarrierOn.
G."3 4":Spreadspectrumto1.23MHzbandwidth.
H."7 1 ***":OutputRFpowerlevel is setpowerlevel2
"***"meansAGClevelandAGClevelrangeisfrom000 to511.
CDMA Portable PCS Telephone 3-4

TEST COMMAND TABLE
COMMANDNO
(OP,AB,RB)COMMANDSWNODESCRIPTION
01(1F,0,0)
02(3F,0,0)
03(FD,0,0)
04(1D,0,1)
05(1C,1,0)
06(1E,0,0)
07(81,0,0)
08(82,0,0)
09(83,4,0)
10(84,1,0)
11(85,0,0)
12(86,0,0)
13(87,0,0)
14(88,0,0)
16(8F,0,0)
17(90,0,0)
18(AE,2,0)
20(94,5,0)
22(91,96,96)
23(95,3,4)
24(9F,7,8)
25(92,0,0)
26(93,0,0)
27(96,0,0)
28(97,0,0)
29(9A,0,0)
30(9D,15,0)
32(A0,1,0)
33(A1,0,0)
34(A2,0,0)
35(A3,3,0)
36(A4,3,0)
38(A6,3,0)
39(A7,3,0)
40(A8,0,3)
41(A9,3,0)
42(AA,1,0)
43(AB,0,0)
44(B0,0,0)
45(B1,0,0)
46(B2,0,0)
T_SUSPEND_I
T_RESTART_I
T_SAVE_VAL_I
T_GET_MODE_I
T_SET_MODE_I
T_WRITE_NV_I
T_CARRIERON_I
T_CARRIEROFF_I
T_LOADSYN_I
T_PWRLEVEL_I
T_RXMUTE_I
T_RXUNMUTE_I
T_TXMUTE_I
T_TXUNMUTE_I
T_STON_I
T_STOFF_I
T_LCD_CONTRAST_I
T_TEST_SYS_I
T_SNDNAM_I1)
T_SNDVERSION_I1)
T_SNDESN_I1)
T_BACKLIGHT_ON_I
T_BACKLIGHT_OFF_I
T_LAMP_ON_I
T_LAMP_OFF_I
T_REBUILD_I
T_PLINE_I
T_SATON_I*2)
T_SATOFF_I*
T_CDATA_I
T_VOLUME_UP_I
T_VOLUME_DOWN_I
T_PCS_CH_FLATNESS_BP_ON_I
T_TXRAS_ADJ_BP_ON_I
T_RXRAS_FLAT_AUTO_I
T_RXRAS_FLATNESS_I
T_DTMFON_I2)
T_DTMFOFF_I
T_COMPANDORON_I
T_COMPANDOROF_I
T_FM_VCLINE_I*
Entertotestmenu
Escapefromtestmenu
SavevaluesinEEPROMonlyinautotest
GetmodeCDMA/FM
SetmodeCDMA/FM
WritetheEEPROMitem
Turnonthecarrier
Turnoff thecarrier
Loadthesynthesizerforlocking
ChangeRFpowerlevel
MuteRX audio
UnmuteRX audio
MuteTXaudio
UnmuteTXaudio
TransmitacontinuousSignalingTone(ST)
StoptransmitacontinuousSignalingTone(ST)
LCDContrastcontrol
RoamTestSystem
Display&SendNAMInformation
Display&SendSoftwareVersion
Display&returnESN
Backlighton
Backlightoff
LAMPon
LAMPoff
RebuildingEEPROM
Displayandreturnproductiondate
EnablethetransmissionofSAT
DisablethetransmissionofSAT
ContinuouslysendTXControldata
ElectricVolumeUp
ElectricVolumeDown
TXrastableadjust
..........
SetsRXAdjustRX RAS
TurnonDTMF
Turnoff DTMF
Turnoncompander
Turnoff compander
EnterFMvoicestate
3-5 CDMA Portable PCS Telephone

COMMANDNOCOMMANDSW NODESCRIPTION
47(B3,3,0)
48(B4,0,0)
49(B5,0,0)
50(B6,0,4)
52(B9,2,2)
55(AC,1,0)
57(BC,0,0)
58(BD,0,0)
59(BE,0,0)
60(BF,3,0)
61(C0,3,0)
62(C1,3,0)
63(C2,3,0)
64(C3,3,0)
65(C4,3,0)
66(C5,3,0)
67(C6,3,6)
68(C8,0,3)
69(C9,0,3)
70(CA,3,0)
71(D1,3,0)
72(D2,3,0)
73(D3,1,0)
74(D4,3,0)
75(D5,0,3)
76(D6,3,0)
77(D7,0,3)
78(D8,0,3)
79(D9,1,0)
80(DA,0,0)
81(E3,0,0)
82(E4,0,0)
83(E5,0,0)
84(E6,0,0)
85(E7,0,0)
86(E8,0,0)
87(E9,0,0)
88(EA,3,0)
89(EB,3,0)
T_FM_AUD_GAIN_I
T_VIBRATOR_ON_I
T_VIBRATOR_OFF_I
T_BATT_TYPE_I
T_HW_VERSION_I
T_EXT_AUDIO_I
T_MIC_ON_I
T_MIC_OFF_I
T_ALLPATH_I
T_FM_TX_GAIN_I2)3)
T_FM_RX_GAIN_I2)3)
T_DTMF_VOL_TX_I2)3)
T_TX_LIMITER_I2)3)
T_FM_SAT_LEVEL_I2)3)
T_FM_FREQ_SGAIN_I2)3)
T_FM_ST_GAIN_I2)3)
T_READ_BATT_I1)
T_VBATT1_I3)
T_VBATT2_I3)
T_WRITE_BATT_I3)3)
T_CDMA_TXADJ_I2)
T_FM_TXADJ_I2)
T_SET_PA_R_I2)
T_TXRAS_ADJ_I
T_READ_RSSI_I3)
T_WRITE_RSSI_I3)
T_READ_TEMP_I
T_RXRAS_AUTO_I
T_BUZZER_ON_I2)
T_BUZZER_OFF_I
T_VOC_PCMLPON_I
T_VOC_PCMLPOFF_I
T_BYPASS_ON_I
T_BYPASS_OFF_I
T_SPEAKER_ON_I
T_SPEAKER_OFF_I
T_FM_LOOP_TEST_I
T_TRK_ADJ_I3)
T_CDTRK_ADJ_I
FMaudiogain
Activateavibrator
Inactivateavibrator
BatteryType
HWversion
ExternalAudioPathOn/Off
MuteMICPath
UnmuteMICPath
Tuneontheall audiopath
AMPSTxAudioGainControl
AMPSRxAudioGainControl
AMPSTxDTMFGainControl
AMPSTxLimiterGainControl
AMPSTxSATlevelControl
AMPSTxMasterGainControl
AMPSTxSTGainControl
SavedLowbatteryvalueread
Set thelowbatterypositioninthe standby
Set thelowbatterypositioninthetalking
writeaBATT
SetsTX_agc_adjforCDMAmode
SetsTX_agc_adjforfm mode
SetsPAR1,R0rangebits
TX RAStableadjust
ReadaRSSI
WriteaRSSI
Readatemperature
AdjRXRASfrom8924C
Buzzeron
Buzzeroff
TurnontoplayaPCMLOOPBACK
Turnoff toplayaPCMLOOPBACK
Turnonthebypass mode
Turnoff thebypass mode
Turnonthe speakerpath
Turnoff the speakerpath
FMloop back
TRK LOCALADJUST
CDMATRK LOCALADJUST
CDMA Portable PCS Telephone 3-6

COMMANDNO
(OP,AB,RB)COMMANDSW NODESCRIPTION
90(F0,2,0)
91(F1,4,0)
92(F2,3,0)
93(F3,3,0)
94(EF,3,0)
95(F4,4,0)
96(F5,4,0)
97(F6,3,0)
98(F7,3,0)
99(FC,3,0)
100(FF,0,0)
T_HW_CHANFLAT_I
T_SW_CHANFLAT_I
T_FM_TX_PWR_I
T_CH_FLATNESS_I
T_RXRAS_ADJ_I
T_PCS_HW_CHANFLAT_I
T_PCS_SW_CHANFLAT_I
T_PCS_CH_FLATNESS_I
T_PCS_CH_MAX_MIN_I
T_SND_GAIN_I
T_MAX_I
-------
-------
Settingthe volumeforpowerlevel2
EdgeChannelMax/MinPowerCode
1)TheAB(InputArgumentByteNumber)values ofthese commandsareusedonlyin
themanualtest.Inautomatictestmode, theABisregardas0.
2)Youcanassignthe value forthese commands.
IftheABvalueisassignedwithout argument,thetestisachievedwiththe value
storedinEEPROM.
3)Afteryouget a desiredtestvaluebyperformingthese commands, ifyouwant to
save the valueintothe correspondingposition.
*OP:OperationCommandNumber
AB:InputArgumentByteNumber
RB: ReturnByteNumber
*SAT32,33 arenotoperatinginMSM@CHIPtest
*46 commandisrequiredinRx,and Txpathtest at AMPSmode
3-7 CDMA Portable PCS Telephone

4.ProductSupport Tools
4-1General
IMPORTANTINFORMATION
Purpose
TheProductSupportTool (PST)offersyoutheabilitytointerface withtheSAMSUNG
PCStelephoneusingaPC.Withthistoolyoucanprogramthephones network
systemrequirementsandfunctionality, swap phonedata,and downloadsoftware
upgrades. ThisdocumentsupportsUniPSTversionx.xx.
NOTE:This softwaremustbe executedintheWindows95/98 mode.
EQUIPMENTREQUIRED
Make sureyouhave the followingequipmentsetup:
1. MinimumPCconfiguration:586 CPU,16MBRAM, Windows95/98,5MBofdisk
space free forsoftwareupgrade.
2.PSTSoftwarewithappropriate cable(DMCable forSAMSUNGPCSphone).
3.SerialPort(16550 SerialInterface Card).
4.PowerSupply(3.8V) orBattery.
INSTALLATION
Software
1.Insert thePSTfloppydiskintodrive (A:\).
2.CreateanappropriatedirectoryontheC:\drive forPSTsoftware, Execute
setup.exe file, Theinstallationprogramcreates folderandtask baronthe
windows95/98 startbar.
SAMSUNGPCS Phone
The serialportshould be configuredtoCOM1orCOM2.
Use the followingproceduretoconnect thephone, cable, and PC.
Plugthe female endoftheDMCableintothe16550 card.
Pull theblackrubberconnectorawayfromthe socket at thebase ofthephone.
Plugthe specialconnectoronthe cableintothe socket at thebase ofthephone.
CDMA Portable PCS Telephone 4-1

4-2PST(ProductSupportTool)
4-2-1 GettingStarted
MAIN MENU SCREEN
1.At theWindows95/98,DoubleClick"UniPst.exe".
2.The MainMenuScreenwill bedisplayed.
The MainMenuScreenshowsthebasictasksthat areavailable.
CAUTION: DONOTattempt toprogramphonewithalow battery.
PSTSETUP
UniPstsupportsSAMSUNGPCSportabletelephone. YoucanselectserialportCOM1
orCOM2.
4-2-2OperationProcedure
Service Programming
TheService Programmingscreens enableyoutoset andchangethe service
activationparametersofthephones. These items canbe changedindividuallyoras
agroupvia the"EditItems"PropertySheetofthePST.
Thereare severalpages ontheService ProgrammingPropertySheet
ReadData fromFile
Click"open"icontoselect thenameofafilewhose extensionis"mmc".The values
will bereadfromthenamedfile, andwill initializetheparametervalues seenonthe
Service programmingscreen
ReadData fromPhone
ClickReadfromthePhoneicontouploadthe currentprogrammableparametersof
thephone. The values arereadfromthephone, sothephonemusthave thepower
ONand beproperlyconnectedtothePST.
NOTE:ToactuallyviewthedatayouneedtogototheEditItems screens.
4-2 CDMA Portable PCS Telephone

EditItems
ClickthisicontoeditNumberAssignmentModule(NAM) itemsorUIitems.
Therearetwotypes of screens:
1.ParametersassociatedwithaparticularNumberAssignmentModule(NAM)
2.UIitems settings
PhoneBook
ClickthisicontoeditPhoneBook.
Whileyoueditcell,youcanuse <Enter>and<UP,DOWN,LEFT,LIGHTArrow>and
<SPACE>key.Ifyouwant toeditphonenumberorname , youmustmove
rectanglebox tocell whereyouwant toedit,Writeitdown.if<UPandDOWN
Arrow>keyispressed,the cursormoves tonextcell orprevious cell.
Save DatatoFile
Clickthisicontosave the currentparameterstoafile. Once youenterafilename,
Click<OK>buttontowriteall currentparameterstothat file. Thiswaythe same
informationcanbedownloadedintomultiplephones.
WritetoPhone
Clickthisicontowritethe selected parametervalues tothephone. Writingthe
selectedvalues tothephonemaytakeuptoaminute.
Iftherearedependencies inafieldyoucanmakeall the changes intheproper
fieldsand downloadtheinformationall together.
Ifyouintendtousethis"WritetoPhone" feature, itisrecommendedthat youdoa
"ReadData fromPhone" first,andthenmakethechanges, sothat nothinggets
inadvertentlyoverwritten.
NOTE:DONOT TOUCHTHEPHONEWHILEWRITINGISINPROGRESS.
Software DownloadandUpgradeScreen
Tobeginasoftwareupgradeordownload,performthe followingsteps:
CDMA Portable PCS Telephone 4-3

1.Fromthemainmenuscreenchoose DOWNLOADMODE
Clickopenicontochoose aBIN fileofthenewsoftwaretobeloaded.Choose the
appropriateBIN file, thenClick<Open>
2.ClickDownloadtobegindownloadingthefile. Youwill noticevariousmessages
andaprogress barthat informstheuserwhat percentageofthedownloadinghas
alreadyoccurred.
3.ClickModeSelectbox,thenSelectSERVICEMODE toreturntotheServiceMode
Screen.
NOTE:DONOTPOWEROFF WHILETHEPHONEISBEING DOWNLOADED!
4-4 CDMA Portable PCS Telephone

5. Exploded View and Parts List
5-1 Main Set Exploded View
5
6
2
8
1
3
13
18
43
19
26
25
38
31
32
39
30
29 28
20
14
15
17
42
41
24
39
40
44
45
22
23
21 35 34
33 37 36
27
16
9
10
12 13
11
7
4
CDMA Portable PCS Telephone 5-1

5-2 CDMA Portable PCS Telephone
5-2 Main Set Parts List
MEA FRONT-SCH6100 GH97-01499A 1 ASS’Y
MEC-FRONT COVER GH75-00332A 1 ASS’Y
1 PMO-FRONT COVER GH72-00560A 1
2 PMO-REFLECTOR LED GH72-00561A 1
3 MPR-SPONGE LCD GH74-00286A 1
4 MPR-TAPE WINDOW GH74-00287A 1
5 PCT-WINDOW LCD GH73-00297A 1
6 WINDOW-LCD BOHO VINYLE GH74-00555A 1
7 RMO-KNOB VOLUME GH73-00316A 1
8 CUSHION-EARPHONE (A) GH74-00530A 1
MEC-HINGE GH75-00046A 2 ASS’Y
9 HINGE-HOUSING GH72-00064A 2
10 HINGE-SHAFT GH72-00061A 2
11 HINGE-CAM GH72-00060A 2
12 HINGE-SPRING GH71-00011A 2
13 HINGE-CAP GH72-00059A 2
MEC-FLIP COVER GH75-00554A 1 ASS’Y
14 FLIP-COVER GH72-00562A 1
15 MAGNECTIC - 1
16 LABEL (R)-FLIP GH68-00664A 1
17 MAIN PBA GH92-00808A 1 ASS’Y
FPCB ASS’Y-VOL/SPK/BUZ GH96-00868A 1 ASS’Y
18 FPCB-VOL/SPK/BUZ - 1
19 RMO-HOLDER BUZZER GH73-00184A 1
20 RMO-CUSHION SPK/BUZ GH73-00298A 1
FPCB ASS’Y-MIC GH96-00867A 1 ASS’Y
21 FPCB-MIC - 1
NO LEVEL DESCRIPTION SEC CODE Q’TY REMARK
1234

22 RMO-HOLDER MIC GH73-00183A 1
23 RMO-CUSHION MIC GH73-00297A 1
MEA REAR-SCH6100 GH97-01500A 1 ASS’Y
MEC-REAR COVER GH75-00335A 1 ASS’Y
24 PMO-REAR COVER GH72-00563A 1
25 PMO-LOCKER MAIN GH72-01224A 1
26 SPRING-LOCKER GH70-10516A 1
27 PMO-EARPHONE COVER GH72-00564A 1
28 NDC-ANT. BUSHING GH71-00035A 1
29 VIBRATOR GH31-00007A 1
30 SPONGE-MOTOR GH74-00516A 1
31 LABEL(R)-QUALCOMM GH68-30846A 1
32 ANTENNA-CONTACT GH71-00056A 1
33 COVER CONNECTOR GH73-00362A 1
34 CUSHION-EARPHONE COVER(B) GH74-00531A 1
35 RMO-SUPPORT LCD GH73-00264A 1
36 MPR-SPONGE TCXO GH74-00247A 1
37 MPR-SPONGE BGA GH74-00246A 1
38 LABEL(R)-BARCODE GH68-30963A 1
39 MACHINE-SCREW 6001-001148 4
40 LABEL(R)-MAIN GH68-00665A 1
41 KEYPAD-DOME GH72-01074A 1
42 FOAM TAPE-FPCD GH74-00132A 1
43 ANTENNA GH42-00034A 1
44 STANDARD-BATTERY PACK GH43-00162A 1
45 EXTENDED-BATTERY PACK GH43-00150A 1 OPTION
NO LEVEL DESCRIPTION SEC CODE Q’TY REMARK
1234
CDMA Portable PCS Telephone 5-3