Samsung MWR-WE13N User manual

1
SAMSUNG
Quick Reference Technical
Handbook
All manuals and user guides at all-guides.com
all-guides.com

2
INDEX
1. Controllers Pages 4-21
2.CAC Split Range Pages 22-39
3.RAC Split Range Pages 40-42
4. VRF Range Pages 43-77
5. Miscellaneous Pages 78-82
For any enquiries or technical support please contact us on:
Ph. 01 2864377
E. [e-mail]
All manuals and user guides at all-guides.com

3
CONTROLLERS
•MWR-WE13N ………………………………………………………………………………………………………………… Pages 4-11
•MWR-WGOOJN ……………………………………………………………………………………………………………….Pages 5-21
These are the most common type of controller in use. For details on other
controllers, please contact GT Phelan.
All manuals and user guides at all-guides.com

4
MWR-WE13N
Initializing Your Wired Remote Controller Communication
Wired remote controller must be initialized if installation status changes.
• Changing number of ventilator (ERV)/indoor unit or their address
Press the Delete and ESC buttons at the same time for more than five seconds.
• Your Wired Remote Controller will be initialized, and the device will search for the indoor
units/ventilator(ERV) connected to your Wired Remote Controller again.
All manuals and user guides at all-guides.com

5
Wired Remote Controller Installation/Service Mode
Additional Functions of Your Wired Remote Controller
If you want to use the various additional functions for your Wired Remote Controller, press the Delete
and Set buttons at the same time for more than three seconds.
•You will enter the additional function settings, and the [main menu] will be displayed.
Refer to the list of additional functions for your Wired Remote Controller on the next page, and select
the desired menu.
•U sing the buttons, select a main menu number and press the [>] button to enter the sub-menu
setting screen.
•Using the buttons, select a sub-menu number and press the [>] button to enter data setting
screen.
•When you enter the setting stage, the current setting will be displayed.
•Refer to the chart for data settings.
•Using the buttons, select the settings. Press the [ ] button to move to the next setting.
•Press the Set button to save the settings and exit to the sub-menu setting screen.
•Press the ESC button to exit to normal mode.
•While setting the data, you can use the [ ]/[ ] buttons to set the range of Data bit.
•While configuring the setting, press the ESC button to exit to the setting sub-menu without saving
your changes.
All manuals and user guides at all-guides.com

6
Wired Remote Controller Installation/Service Mode
Installation/Service Mode
All manuals and user guides at all-guides.com
all-guides.com

7
Installation/Service Mode (Cont.)
All manuals and user guides at all-guides.com

8
User Setting Options
How to Set the Additional User Functions
1If you want to set the detailed settings, press the User Set button.
You will enter the User Set mode, and the [Main Menu] is displayed.
2Refer to the wired remote controller's User Set list on the next page to select the desired menu.
Using the [ UP ]/[ DOWN ] buttons, select a main menu number and press the [>] button to enter the submenu setting
screen.
Using the [ UP ]/[DOWN ] buttons, select a sub-menu number and press the [> ] button to enter the data setting screen.
Once you have entered the setting screen, the current setting is displayed.
Refer to the chart for data setting.
Using the [ UP]/[ DOWN] buttons, change the settings and press the [ >] button to move to the next setting.
Press the Set button to save the setting and exit to the sub-menu setting screen.
Press the ESC button to exit to normal mode.
All manuals and user guides at all-guides.com

9
Setting Additional User Functions (Cont.)
All manuals and user guides at all-guides.com

10
Setting Additional User Functions (Cont.)
All manuals and user guides at all-guides.com

11
MWR-WG00JN
Tracking Your Indoor Unit from the Wired Remote Controller
Tracking of your Wired Remote Controller will automatically start when you turn on the power after
installation.
If you want to perform tracking again after installation, then press the and buttons at the
same time for more than 5 seconds.
The system will reset, and tracking will start again.
During tracking, the total number of currently searched indoor units and ventilator(ERV) will be
displayed.
NOTE
The operation displays on the remote controller may differ depending on the selected language.
If you want to perform tracking again after installation, then press the LEFT and SETTINGS buttons at
the same time for more than 5 seconds.
Initializing Your Wired Remote Controller Communication
Wired remote controller must be initialized if installation status changes.
Changing number of ventilator (ERV)/indoor unit or their address
Press the buttons at the same time for more than 5 seconds.
Your Wired Remote Controller will be initialized, and the device will search for the indoor units/
ventilator(ERV) connected to your Wired Remote Controller again.
All manuals and user guides at all-guides.com
all-guides.com

12
Installation/Service Mode
All manuals and user guides at all-guides.com

13
Installation/Service Mode (Cont.)
All manuals and user guides at all-guides.com

14
Installation/Service Mode (Cont.)
All manuals and user guides at all-guides.com

15
Installation/Service Mode (Cont.)
All manuals and user guides at all-guides.com

16
Installation/Service Mode (Cont.)
All manuals and user guides at all-guides.com
all-guides.com

17
Installation/Service Mode (Cont.)
All manuals and user guides at all-guides.com

18
User Setting Options
All manuals and user guides at all-guides.com

19
User Option Codes (Cont.)
All manuals and user guides at all-guides.com

20
User Option Codes (Cont.)
Current Time Setting (Example)
1Press the SETTING button.
2Press the UP,DOWN or LEFT,RIGHT button to select Option, and then press the OK button.
3Press the UP,DOWN or LEFT,RIGHT button to select User mode, and then press the OK button.
4Press the UP,DOWN or LEFT,RIGHT button to select Wired remote controller, and then press the OK button.
5Press the UP,DOWN or LEFT,RIGHT button to select Current time, and then press the OK button.
6Press the UP,DOWN or LEFT,RIGHT button to select Time, and then press the OK button.
7Press the UP,DOWN or LEFT,RIGHT button to select Time format, Hour, Minute and AM/PM, and then press the OK button
All manuals and user guides at all-guides.com