Samsung MCM-A202DN User manual

OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 12 2013-02-06 오후 6:40:09

OnOff Controller
MCM-A202DN
Air Conditioner
installation manual
imagine the possibilities
Thank you for purchasing this Samsung product.
This manual is made with 100% recycled paper.
EN
DB68-03721A(1)
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 13 2013-02-06 오후 6:40:09

Safety Precautions
 Read carefully this installation manual before installation and check
whether the OnOff controller is installed correctly after installation.
 Do not attempt to install or repair this OnOff controller by yourself.
 This OnOff controller contains no user-serviceable parts. Always
consult authorized service personnel for repairs.
 When moving, consult authorized service personnel for
disconnection and installation of the OnOff controller.
 Ensure that the wall is strong enough to support the weight of the
OnOff controller.
 The OnOff controller must be installed according to the national
electrical rules by an installation specialist.
 When wiring, connect the supplied wires firmly and fasten them
securely so that external force cannot be applied to the terminal
connection area.
 Position all the wires correctly so that the cover of the electric
equipment section doesn’t float. Then securely fasten the cover.
 Before handling or adjusting the power loading terminal, switch
off the power supply.
 When you want to disuse the OnOff controller, consult authorized
installation center.
WARNING
CAUTION  Do not use inflammable gases near the OnOff controller.
 Do not install the OnOff controller in a location where it will come
into contact with the combustible gases, machine oil, sulphide gas,
etc.
 Avoid a location where acid/alkali solution or special spray is used.
 Choose a location that is dry and sunny, but not exposed to direct
sunlight. Available temperature is between 0°C(32°F) and 39°C(102°F).
 Do not spill water into the OnOff controller.
 Do not give tensile strength to the cable to avoid disconnection.
 Do not press buttons with a pointed thing.
 Do not connect the power cable to the control terminal.
 If the OnOff controller is installed in a hospital or other special
places, it should not affect other electronic devices.
 Do not install the product in an area where mineral oil is kept or
arsenic acid of oil and steam frequently exist such as a kitchen.
 Do not install the product in an area where corrosive gases such as
ammonia gas or sulfurous acid gas are generated e.g. an exhaust
pipe of a toilet or an outlet of ventilating opening.
 Do not install the product in an area where a machine that
generates electromagnetic waves is placed.
 Do not install the product in an area where combustible gas
leakage is expected or volatile flammable material such as thinner
and gasoline are handled.
 Do not install the product in an area where carbon textile or
flammable dust float in the air.
 Do not install the product in an area where corrosion is expected
such as shoreline and hot spring.
This installation manual indicates you to install the OnOff controller which is connected to
the indoor unit. For installation of other optional accessories, see an appropriate installation
manual.
2
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 2 2013-02-06 오후 6:40:07

3
OnOff Controller Installation
Accessories
OnOff
Controller (1)
Cable-tie (2) Cable Clamp (5) M4x16 Tapped
Screw (7)
User’s manual (1)
Installation
manual (1)
Wiring Diagram
Number of indoor unit that connect to the same OnOff controller is up to 128. It can be connected
to the communication terminal of the indoor unit.
RMC(1) address
set to “0”
OnO
controller
OnO
controller
Outdoor unit
Outdoor unit
Outdoor unit
Indoor unit
Indoor unit
Indoor unit Indoor unit Indoor unit Indoor unit Indoor unit Indoor unit
Indoor unit Indoor unit Indoor unit Indoor unit Indoor unit
Indoor unit Indoor unit Indoor unit
RMC
00
RMC
04
RMC
OA
RMC
OB
RMC
OC
RMC
OD
RMC
OE
RMC
OF
RMC
05
RMC
06
RMC
07
RMC
08
RMC
09
RMC
01
RMC
02
RMC
03
Wire range that can
be connectable
Rated
Dimension
Stud
Dimension
Basic dimension [mm (inch)]
AWG mm2
(inch2)
mm2
(inch2)
mm
(inch) t Φd1 E F W L
22~16
0.25 ~
1.65
(0.0003 ~
0.0025)
1.5
(0.0023)
3
(0.1181)
0.7
(0.0275)
3.8
(0.1496)
4.5
(0.1771)
6.3
(0.2480)
5.5
(0.2165)
19.05
(0.75)
Φd1
Silver soldering
Stud
W
Selecting pressure connection terminal
 Based on the normal dimension of the connecting power cable, select the pressure connection
terminal.
 Insulate the connection area between pressure connection terminal and the connecting
power cable with sheath.
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 3 2013-02-06 오후 6:40:08

4
OnOff Controller Installation (Continued)
Setting up the installation option of Indoor
Unit and OnOff Controller
1Set the Indoor Unit installation option SEG5 to “1”.
It means use the OnOff controller.
2Set the RMC(1) and RMC(2) address of Indoor Unit.
Example) RMC(1) = SEG11 = 0~F, RMC(2) = SEG12 = 0~F
However, when RMC(1) = F, RMC(2) can be set between 0~E
In Case of Installing OnOff Controller Only
OnOff Controller
 You must reset the OnOff controller to apply the changed
RMC(1) address.
SW22
SW21
SW22
SW21
DIP Switch
RMC(1) address
(SW01) = 0~F
Cooling/Heating switch
Cooling
Heating
OFF : Left
ON : Right
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 4 2013-02-06 오후 6:40:08

5
OnOff Controller Installation (Continued)
Indoor Unit option code system
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12
0X X X X X 1 X X X X X
SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24
2X X X X X 3 X X X X X
SEG2 = A : Address option
= 2 : Installation option
X
SEG5 = 0 : not use the OnOff controller
= 1 : use the OnOff controller - When setting the installation option
X
SEG11 SEG12 = RMC(1), RMC(2)
address (00~FE)
SEG9 - When setting the address option
= 1: RMC address setting
X X X
Note  Detailed method about Installation option establishment refers to Indoor
Unit manual.
 Installation option must set the SEG2 value as "2" in Indoor Unit option code
 Address option must set the SEG2 value as “A" in Indoor Unit option code
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 5 2013-02-06 오후 6:40:08

6
OnOff Controller Installation (Continued)
Different Levels of the OnOff Controller
 Adjust the DIP switch in the OnOff controller PCB and set a level.
This will enable the user to control the indoor units
connected to the OnOff controller according to the set level.
 Level application and authorization for controlling from OnOff
controller can be restricted depending on the Level setting from
the upper controller with priority.
Ex) OnOff controller cannot control the indoor units if the control
level set from the DMS is higher than the level of
OnOff controller.
Switch
No.
SW22 Meaning
1 2
LEVEL 0 OFF OFF
Among the various controllers, such as the OnOff
controller, wired/wireless controller and the indoor
unit button, the air conditioner will only be able to
operate with the most recently used controller
LEVEL 1 ON OFF
The wired/wireless controller can only be used
when the OnOff controller is powered on.
LEVEL 2 OFF ON
The air conditioner can only be operated with
the OnOff controller.
Note  The LEVEL of the OnOff controller is ‘0’ when all the
switches are in the 'OFF' position.
 Changed LEVEL will be applied immediately when you
turn on or off the operation with an OnOff controller.
SW22
SW21
SW22
SW21
DIP Switch
RMC(1) address
(SW01) = 0~F
Cooling/Heating switch
Cooling
Heating
OFF : Left
ON : Right
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 6 2013-02-06 오후 6:40:08

7
OnOff Controller Installation (Continued)
Setting the option for OnOff controller
1You can adjust the DIP switch (SW21) on PCB of the OnOff
controller to set the option and control the OnOff controller
according to the selected option.
SW21 Contents
1 2
ON - Disable OnOff controller usage
OFF -
Enable OnOff controller usage
 All the DIP switches of the OnOff controller is set to OFF as
factory default setting.
 SW21 setting of the DIP switch will be applied instantly.
 Option setting for communication can be executed regardless of
the Level setting.
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 7 2013-02-06 오후 6:40:08

8
OnOff Controller Installation (Continued)
Outdoor unit
OnO
controller
OnO
controller
OnO
controller
RMC(1) address
set to “0”
RMC(1) address
set to “1”
RMC(1) address
set to “2”
Indoor Unit
#1~#15 assign
Indoor Unit
#16~#31 assign
Indoor Unit
#32~#64 assign
To install 128 units to 16 or less number of outdoor units.
(Group control of units)
Control layer connection
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 8 2013-02-06 오후 6:40:08

9
OnOff Controller Installation (Continued)
Indoor unit
ADDRESS
RMC(1) 0
RMC(2) 0 1 2 3 4 5 6 7 8 9 A B C D E F
Indoor unit
ADDRESS
RMC(1) 1
RMC(2) 0 1 2 3 4 5 6 7 8 9 A B C D E F
Indoor unit
ADDRESS
RMC(1) 2
RMC(2) 0 1 2 3 4 5 6 7 8 9 A B C D E F
Indoor unit
ADDRESS
RMC(1) 2
RMC(2) 0 1 2 3 4 5 6 7 8 9 A B C D E F
Indoor unit
31
Indoor unit
30
Indoor unit
29
Indoor unit
18
Indoor unit
17
Indoor unit
16
Indoor unit
32
Indoor unit
33
Indoor unit
34
Indoor unit
45
Indoor unit
46
Indoor unit
47
Indoor unit
63
Indoor unit
62
Indoor unit
61
Indoor unit
50
Indoor unit
49
Indoor unit
48
Indoor unit
0
Indoor unit
1
Indoor unit
2
Indoor unit
13
Indoor unit
14
Indoor unit
15
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 9 2013-02-06 오후 6:40:09

10
OnOff Controller Installation (Continued)
Outdoor unit
OnO
controller
OnO
controller
OnO
controller
RMC(1) address
set to “0”
RMC(1) address
set to “1”
RMC(1) address
set to “2”
Indoor Unit
#1~#15 assign
Indoor Unit
#16~#31 assign
Indoor Unit
#32~#64 assign
To install 80 units for 1 outdoor unit
(Group control of units)
Set layer connection
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 10 2013-02-06 오후 6:40:09

11
OnOff Controller Installation (Continued)
Indoor unit
ADDRESS
RMC(1) 0
RMC(2) 0 1 2 3 4 5 6 7 8 9 A B C D E F
Indoor unit
ADDRESS
RMC(1) 1
RMC(2) 0 1 2 3 4 5 6 7 8 9 A B C D E F
Indoor unit
ADDRESS
RMC(1) 2
RMC(2) 0 1 2 3 4 5 6 7 8 9 A B C D E F
Indoor unit
ADDRESS
RMC(1) 2
RMC(2) 0 1 2 3 4 5 6 7 8 9 A B C D E F
Indoor unit
31
Indoor unit
30
Indoor unit
29
Indoor unit
18
Indoor unit
17
Indoor unit
16
Indoor unit
32
Indoor unit
33
Indoor unit
34
Indoor unit
45
Indoor unit
46
Indoor unit
47
Indoor unit
63
Indoor unit
62
Indoor unit
61
Indoor unit
50
Indoor unit
49
Indoor unit
48
Indoor unit
0
Indoor unit
1
Indoor unit
2
Indoor unit
13
Indoor unit
14
Indoor unit
15
OnOff Controller MCM-A200DN_IM_EN_03721A(1).indd 11 2013-02-06 오후 6:40:09