Samsung STC-14 User manual

Security IR Camera STC-14 User’s Manual
Thank you for purchasing a SAMSUNG Security IR Camera.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
ENGLISH

This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the
equipment.
WARNING - To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.

Security IR Camera User’s Manual
4
Security IR Camera User’s Manual
5
Contents Features
The STC-14 Security IR Camera is a contactless monitoring device capable of
measuring the surface temperatures of all target areas, and displaying the
resulting data via temperature distribution images (thermal images).
Because the STC-14 is equipped with a two-dimensional uncooled thermal
sensor (microbolometer) incorporating the latest technology, neither sensor
cooling nor sensor maintenance are required. In addition, its sensor boasts long
wavelength sensitivity (detecting infrared radiation with wavelengths between
8-14 μm from targets and background), allowing it to produce high resolution
thermal images with minimal impact from sunlight, even during outdoor daytime
monitoring in clear weather.
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products. The Eco mark represents
Samsung Techwin's will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
• Features ………………………………………………………………………… 5
• Warnings & Cautions ……………………………………………………… 6
• Warnings ………………………………………………………………………… 7
• Cautions ………………………………………………………………………… 8
• Overview ………………………………………………………………………… 9
• External Part Names ………………………………………………………… 10
■
Names of external camera parts 

■
Names of internal camera parts 

■
Assembly/Adjustment Methods 
• Installing the Camera ……………………………………………………… 12
■
Inputting Power 

■
Startup 

■
Calibration (NUC) 

■
Monitor/Communications Connection  

■
Monitoring Guidelines  

■
Storage 
• Interface ………………………………………………………………………… 15
• Operating the Camera ……………………………………………………… 18
■
Function Menu Configuration  
■
Function Settings Methods 
•BRIGHTNESS
  

•CONTRAST
 
•RANGE
 

•NUC (calibration)
 
•NUC MODE (calibration mode)
 

•IMAGE ADJ
 

•SPECIAL (environment settings mode)
 

•SAVE
 
•EXIT (close menu)
  
• Specifications ……………………………………………………………… 28
• Troubleshooting …………………………………………………………… 29
• Dimension …………………………………………………………………… 30

Security IR Camera User’s Manual
6
Security IR Camera User’s Manual
7
Refrain from installing the product
yourself.
Both technical expertise and experience are required in order
to install the product. A fire or electric shock could result if a
customer installs the product by themselves. Contact your
sales agent for all matters pertaining to installation.
Stop using the product if smoke is emitted from the
camera or an abnormal amount of heat is produced.
Failure to obey this warning could result in a fire.
Always install a lightning rod when setting
the product up independently outdoors.
Failure to obey this warning could result in product
failure, electric shock, or fire.
Do not install the product in an
insecure mounting location.
Failure to obey this warning could result in the
product falling off.
Do not touch the power plug with wet
hands.
Failure to obey this warning could result in an electric
shock.
Do not disassemble the product or
insert foreign objects.
Failure to obey this warning could result in a product
failure or fire.
There is a risk of death or serious injury if the designated instructions are not
adhered to.
The action is forbidden.
Disassembly is forbidden.
There is a risk of personal injury or property damage if the designated
instructions are not adhered to.
Explanation of Warnings/Cautions/Displays
Warnings & Cautions
The following points are presented in order to promote customer safety and prevent
property damage. After reading this information, be sure to use the product in the correct
manner.
* Please direct any product inquiries towards the merchandiser from which the device was purchased. Be aware that
if service is carried out, customers are responsible for any costs pertaining to the use of expensive ladders or other
equipment.
* Ensure that the power plug is disconnected around times in which electrical storms are experienced. (This prevents
fire and product failure)
* This product is an auxiliary device that is used as part of a monitoring system. Samsung Techwin will not be held
liable in cases when personal or property damage is caused due to theft, fire, or other unavoidable occurrences.
Warnings

Security IR Camera User’s Manual
8
Security IR Camera User’s Manual
9
1STC-14, camera sun shield
2Screws for fastening camera (4×M3XL12)
3L-type hexagon wrenches (3: 1.5 mm/2.5 mm/3.0 mm)
4Bolts for fastening camera (2)
5Adapter (Input: AC 220 V/60 Hz, Output: AC 24 V/60 Hz)
6Lens cap
7User’s Manual
Position the camera so that it is not facing
towards the sun or any other bright light source.
Failure to obey this caution could result in the
microbolometer being damaged beyond repair.
Do not install the product in very hot
or very cold locations.
Using the product in an area with very hot (55°C or higher) or
cold (-30°C or lower) temperatures could result in product
failure, or a reduction in image quality. Ensure proper ventilation
when installing the product in particularly hot locations.
Do not drop the product, or subject it
to strong impacts or vibrations.
Failure to obey this caution could result in product
failure.
Do not touch the camera lens with
your hands or fingers.
The lens is the most important part of the camera.
Ensure the lens is kept free of fingerprints, etc.
❶ 2 3
5 6 7
4
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard), or 0.197" (ASA
standard)
Cautions
Overview

Security IR Camera User’s Manual
10
Security IR Camera User’s Manual
11
1Video signal/communications (RS485) cable
2Power cable (AC 24 V, 50/60 Hz)
3Lens (14 mm)
4Support platform for fastening camera
1Lens (14 mm)
2Key SW
3Key SW terminal block
4IF terminal block
1 2 34
Names of external camera parts
Names of internal camera parts
Front Rear
13 4
2❶ A screw to fix the focus is located on the bottom of the lens.
2
A sun shield is provided with this camera to allow for outdoor installation.
Using the bolts and hexagon wrenches included in this package, fasten the camera unit
and sun shield firmly in place. (Do not use excessive force during assembly.)
❶
2
External Part Names
• Do not adjust the focus after purchasing this product, because it will have been set to
the optimum position. Incorrectly adjusting the focus will hinder the camera’s
performance.
Notes
Assembly/Adjustment Methods

Security IR Camera User’s Manual
12
Security IR Camera User’s Manual
13
Inputting Power
Startup
Connect the video output terminal on the rear of this product to the monitor.
■Connecting the Monitor
IR camera Intermediate video receiver End equipment
* Deviations may occur depending on the type of power cable shown in the chart above, and on the
wiring manufacturer.
When the resistance value of copper wire is at [20°C(68°F)]
Copper wire size (AWG)
#24(0.222) #22(0.332) #20(0.522) #18(0.832)
Resistance (Ω/m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
 •Thisdeviceisnotfittedwithapowerswitch.Thedevice
must be provided with power to turn it
 •Aftercheckingthelabelonthecableontherightsideof
the camera, connect the output cable of the provided
adapter.
 •Refertotheowner’smanualforeachdevice.Connectionmethodsemployedmaydiffer
depending on the monitors and peripheral devices used.
 •Beforeconnectingdevices,ensuretheirpoweristurnedoff.
 •Adjustthe75Ω/Hi-Zconversionswitchforeachdevicebasedonthefollowing
illustration.Select“Hi-Z”forintermediatevideoreceiversand“75Ω”forendequipment.
Calibration (NUC)
Monitor/Communications Connection
Installing the Camera
1. Remove the lens cap.
2. Engage the power. (Use the adapter provided with this product.)
3.TheratedinputvoltageforthisproductisAC24V,50/60Hz.
1.TheSTARTscreenwillappearafterthepowerhasbeenturnedon.
2. After completion of initialization, thermal images will be displayed. (approx. ten seconds
after engaging the power)
Thisdevicewillperformacalibrationnecessaryforimaging(NUC)aftertheinternalshutter
closes.
During NUC, the screen will freeze momentarily. Please note that this is not a malfunction.
Thesensorwillnotoperateproperlyimmediatelyafterthepoweristurnedon,orwhenswitching
between HIGH and LOW ranges. As a result, thermal images will not display consistently for several
seconds.Menucontrolscanbeusedtosavevaluestobeappliedatsubsequentstart-upofthe
STC-14.(Ifvaluesarenotsaved,thenthelastsavedsettingswillbeapplied.)
• A 22-18 gauge power wire is recommended for this camera.
• Voltage reinforcement will occur based on the length of the power wire. If the adapter
output wire is too long, camera performance may suffer.
Notes
IR camera Monitor

Security IR Camera User’s Manual
14
Security IR Camera User’s Manual
15
Interface
Attach the lens cap before storing this device.
Ensure that the storage area is kept within the allowable temperature range listed in this
device’sproductspecifications.Donotplacethisdeviceinalocationwherecondensation
may occur.
A user interface terminal block is attached to the inside of this device.
Aftermakingadjustmentstotheinternalterminalblock,ensurethatthebackcoveris
properly attached.
3.AlwayscarryoutanNUCwheneversunlightorhightemperatureobjectsarewithinthe
field of view.
4. When the camera is used continuously for a long period of time, pay attention to the
buildup of dirt on the lens. A dirty lens may result in phenomena such as shortened
detection distances.
5. Even if the same item is being monitored, changes in environmental conditions such as
rain and fog will affect detection distance. Ensure the camera is operated while being
aware of how such changes may influence detection distance.
6. In order to operate the camera properly, ensure suitable usage conditions during
monitoring.
External communications cable RS485 control terminal
(+) CONNECTION TERMINAL (TRX+) 485+
(-) CONNECTION TERMINAL (TRX-) 485-
Storage
Installing the Camera
UsingRS485communications,functionsettingsmenuscanbeadjustedusingtheSamsung
TechwinDVRorSystemcontroller.
(1) Controlling menus using a PC
Using an RS485 converter, connect the camera's RS485 control terminal to a serial cable.
Example) PC serial board (COM1)  serial cable  RS485 converter  camera RS485 control
terminal
(2) Controlling menus using a DVR system controller
ConnectanRS485cable(TRX+,TRX-)toanRS485controlboardconnectionterminalcapableof
connecting to the DVR system controller.
■RS485 Communications Controls
Communications Settings Default Values (camera default values at the time of shipment)
• Please use Samsung Techwin Protocol or Pelco-D Protocol when controlling the camera
with a separate controller.
Notes
• Leakage may occur if the back cover is not properly attached.
Notes
After thermal images appear, the camera will begin to monitor its range of coverage.
1.Donotadjustthefocusifthereisnoparticularpointoffocustomonitor.
2.Foranin-depthexplanationofthecontrolsusedwiththeSTC-14,refertothesection
detailing how the camera is operated on page 16.
Duringmonitoring,theSTC-14willcaptureheatsourcesanddisplaytheresultingimageson
the monitor.
1.Ifthesubjectenvironmentexperiencesadramaticchangeintemperatureduring
monitoring,besuretosetNUCMODEtoeitheranINTERVALof10MINorless,oranAMB
of 1.0°C or lower .
2. Please be aware that because this is an infrared camera, reflections not visible to the
naked eye may still be displayed. Images reflected off glass or mirrors located in front of
the camera may become visible.
Interface
Monitoring Guidelines

Security IR Camera User’s Manual
16
Security IR Camera User’s Manual
17
Function Explanation Notes
RS485 I/F
(R+/-, D-/+)
Operates the RS485 I/F.
Because full-duplex communication
is supported, this function is used
to update F/W.
Standard users should utilize the
same cables as those employed at
the time of shipment.
Shipment status : R+,D+ => TRX+
R-,D- => TRX-
Communication terminator
settings:
- Default value: ON
- If multiple cameras are installed :
Turn only the camera measuring
the furthest distance ON, and the
remaining cameras OFF.
Video output
(Video)
Acts as a composite video signal
output.
Switch between NTSC/PAL using
the menu.
Power supply
(POW+/-) Provides power. AC 24 V, 50/60 Hz
KEY contact
output
Operates menu controls.
(Has the same connection as the
circuit board KEY.)
This output is provided for
adjustment purposes. For that
reason, please refrain from
extending the controls to several
meters or longer.
(For remote control operation, use
RS485 I/F.)
LED
Notifies users using the LED
display whether the power is ON/
OFF, and whether a device
abnormality or warning has
occurred.
Power ON : Lighting
Device Abnormality/Warning :
Flashing
KEY controls Enables operation of the menu
controls. Used to make adjustments.
①
③
②
④
⑤
■Connector specifications and signals
<Function Chart>
① POWER LED
•PowerON:Lit
•Abnormality/Warning:Flashing
② Terminal Block A
③ RS485 Terminator SW
•TerminatorON:1-2
•TerminatorOFF:2-3
④ Multi Direction S/W : same connector as Terminal Block B
⑤ Terminal Block B
PIN Name Explanation
1 R+ RS485+ Communications Non-inverting input/output
2 R- RS485- Communications Inverting input/output
3 D- RS485- Communications Inverting input/output
4 D+ RS485+ Transmission Non-inverting input/output
5 G Ground
6 Video Composite video signal
Impedance : 75 Ω
7 G Ground
8 POW+ Power input AC +24 V
9 POW- Power input DC AC -24 V
PIN Name Explanation
1 *UP KEY UP contact input (Active LOW)
2 *DOWN KEY DOWN contact input (Active LOW)
3 *LEFT KEY LEFT contact input (Active LOW)
4 *RIGHT KEY RIGHT contact input (Active LOW)
5 *SET KEY SET contact input (Active LOW)
6 GND GND
7 MD Terminal used when product is shipped from the factory.
Interface
■Rear Terminal Placement
• Before supplying a terminal block with power, verify that the wiring has been properly
connected.
Notes

Security IR Camera User’s Manual
18
Security IR Camera User’s Manual
19
Function Menu Configuration
Functionsettingsmaybeadjustedusingtheinternalswitchesafterremovingtherear
cover.(Referto“5.Interface”fordirectionsonhowtoremovetherearcover.)
UPbutton :Movethemenucursorup.
RIGHTbutton:Increase(+)thesettingsvalueoftheselecteditem.
DOWNKey :Movethemenucursordown.
LEFTbutton :Decrease(-)thesettingsvalueoftheselecteditem.
SETbutton :Ifa“ ”iconisdisplayed:Movetoascreenwhereyoucanselectsettings
values (move down a level)
If a “ ”iconisnotdisplayed:Executeoradjusttheselecteditem
PresstheSETbuttontodisplaytheMAINSETUPmenuscreen.TheMAINSETUPmenu
uses a tree structure. When you select a function, a sub menu will appear.
UP
SET (Push)
RIGHT
DOWN
LEFT
Function Explanation
BRIGHTNESS AUTO / MANUAL (level ranging from 1-10)
CONTRAST AUTO / MANUAL (level ranging from 1-10)
RANGE AUTO / L/H
NUC NUC
NUC MODE
INTERVAL / AMB / MANUAL
INTERVAL 0H 1MIN-24H 0MIN
AMB 0.1°C-5.0°C
IMAGE ADJ
3D-DNR OFF/L/M/H
SHARPNESS 0-5
ZOOM OFF/X2/X4
POLARITY BW/WB
SPECIAL
TV SYSTEM NTSC/PAL
LANGUAGE ENGLISH / OTHERS
COMM ADJ CAMERA ID 0-255
BAUD RATE 4800/9600/19,200/38,400
UART MODE BIT/PARITY/STOPBIT
8-O-1
8-N-1
8-E-1
RET PKT ON/OFF
CAMERA ID ON/OFF
RESET
SAVE SAVE
EXIT EXIT
< Control buttons >
Function Settings Methods
Operating the Camera
MAIN SETUP
1. BRIGHTNESS AUTO
2. CONTRAST MANUAL
3. RANGE AUTO
4. NUC
5. NUC MOOE INTERVAL
6. IMAGE ADJ
7. SPECIAL
8. SAVE
9. EXIT
Use the UP button or DOWN
button to select the item you
would like to set.
UsetheRIGHTbuttonorLEFT
button to change the status of
the corresponding setting.

Security IR Camera User’s Manual
20
Security IR Camera User’s Manual
21
UsethisoptiontoswitchbetweenanLRangeandHRangesettings.Select“AUTO”toallowthe
settings to automatically change between L Range and H Range based on the surrounding
temperature.Choose“L”tokeepthetemperaturerangeatLRangeregardlessofthesurrounding
temperature.Inthesameway,select“H”toalwayshavethetemperaturerangesetatHRange.
3.PresstheLEFTbuttonorRIGHTbuttonwhilethecursorisalignedwith“3.RANGE”toswitchthe
RANGEsettingfrom:AUTO  L  H  AUTO.(Defaultvalue:AUTO)
4.PresstheSETbuttonwhilethecursorisalignedwith“4.NUC”tocalibrate.Screenoperationswill
then be temporarily suspended.
MAIN SETUP
1. BRIGHTNESS AUTO
2. CONTRAST MANUAL
MAIN SETUP
1. BRIGHTNESS AUTO
2. CONTRAST MANUAL
3. RANGE AUTO
MAIN SETUP
1. BRIGHTNESS AUTO
2. CONTRAST MANUAL
3. RANGE AUTO
4. NUC
MAIN SETUP
1. BRIGHTNESS AUTO
2. CONTRAST MANUAL
3. RANGE AUTO
4. NUC
5. NUC MOOE INTERVAL
Operating the Camera
BRIGHTNESS
RANGE
NUC (calibration)
CONTRAST
1.PresstheSETbuttonwhilethecursorisalignedwith“1.
BRIGHTNESS”todisplaytheBRIGHTNESSsubmenushown
below.PresstheLEFTbuttonorRIGHTbuttonwhilethecursoris
alignedwith“AUTO”toswitchtheBRIGHTNESSAUTOADJUST
settingfrom:ONOFFON.
 PresstheLEFTbuttonorRIGHTbuttonwhilethecursorisaligned
with“MANUAL”toadjusttheBRIGHTNESSovertendifferent
levels:12 3 4 5 6 78 9 10 
1.Select“2.RETURN”toconfirmthecurrentsettingandgo
backtotheMAINSETUPmenuscreen.(Defaultvalue:AUTOON)
2. PresstheSETbuttonwhilethecursorisalignedwith“2.
CONTRAST”todisplaythefollowingsubmenu.PresstheLEFT
buttonorRIGHTbuttonwhilethecursorisalignedwith“AUTO”
toswitchtheCONTRASTAUTOADJUSTsettingfrom:ON 
OFF  ON.
PresstheLEFTbuttonorRIGHTbuttonwhilethecursorisalignedwith“MANUAL”toadjustthe
CONTRASTovertendifferentlevels:12 3 4 5 6 78 9 10 1. Select
“2.RETURN”toconfirmthecurrentsettingandgobacktotheMAINSETUPmenuscreen.(Default
value:6)
*InorderfortheCONTRASTAUTOsettingtobeenabled,theBRIGHTNESSAUTOsettingmustalreadybe
turned on.
Accordingly,ifAUTOcannotbesetto“ON”,enabletheBRIGHTNESSAUTOsettingandthenturnonthe
CONTRASTAUTOsetting.
BRIGHTNESS
▶ 1.MANUAL 5
2.RETURN
CONTRAST
▶ 1.MANUAL 5
2.RETURN

Security IR Camera User’s Manual
22
Security IR Camera User’s Manual
23
SelectanNUCoperationmode.Ifyouchoose“MANUAL”,theuseristoperformNUCmanually,
instead of having the device conduct calibration automatically.
5.PresstheSETbuttonwhilethecursorisalignedwith“5.NUCMODE”todisplaythefollowing
NUCMODEsubmenu.PresstheLEFTbuttonorRIGHTbuttonwhilethecursorisalignedwith
“5.NUCMODE”toswitchfrom:INTERVAL  AMB  MANUAL  INTERVAL.PresstheSETbutton
againtoadjustthesubmenu.Select“2.RETURN”toconfirmthecurrentsettingandgobackto
theMAINSETUPmenuscreen.(Defaultvalue:INTERVAL)
 ·INTERVAL:AnNUCwillbeperformedatthespecifiedINTERVAL.
 ·AMB :AnNUCwillonlybeperformedwhenatemperaturechangemeetingtheset
temperature(0.1°C-10.0°C)isdetectedbytheinternaltemperaturesensor.
 ·MANUAL :AnNUCwillnotbeperformed.
Usethismenutoadjustimages.Afteryouselectthisoption,thefollowingsubmenuwillappear.

ZOOM(digitalzoomsettings):
  PresstheLEFTbuttonorRIGHTbuttonwhilethecursoris
alignedwith“3.D-ZOOM”toswitchthezoomsettingfrom:
OFF  X2(timestwo)  X4(timesfour)  OFF. Select “5.
RETURN”toconfirmthecurrentsettingandgobacktothe
MAINSETUPmenuscreen.(Defaultvalue:OFF)

SHARPNESS(edgeemphasis):
Use this option to use image processing to emphasize
edges.PresstheLEFTbuttonorRIGHTbuttonwhilethe
cursorisalignedwith“2.SHARPNESS”toswitchthe
SHARPNESSsettingfrom0-5.Select“5.RETURN”to
confirmthecurrentsettingandgobacktotheMAINSETUP
menuscreen.(Defaultvalue:4)

3D-DNR(noisereduction):
 PresstheLEFTbuttonortheRIGHTbuttontolimitthe
amountofnoiseproduced.(Defaultvalue:M)
MAIN SETUP
1. BRIGHTNESS AUTO
2. CONTRAST MANUAL
3. RANGE AUTO
4. NUC
5. NUC MOOE INTERVAL
6. IMAGE ADJ
7. SPECIAL
Operating the Camera
NUC MODE (calibration mode) IMAGE ADJ
MAIN SETUP
1. BRIGHTNESS AUTO
2. CONTRAST MANUAL
3. RANGE AUTO
4. NUC
5. NUC MOOE INTERVAL
6. IMAGE ADJ
IMAGE ADJ
1.3D-DNR OFF
2.SHARPNESS OFF
▶ 3.D-ZOOM X2
4.POLARITY BW
5.RETURN
IMAGE ADJ
1.3D-DNR OFF
▶ 2.SHARPNESS OFF
3.D-ZOOM X2
4.POLARITY BW
5.RETURN
IMAGE ADJ
▶ 1.3D-DNR OFF
2.SHARPNESS OFF
3.D-ZOOM X2
4.POLARITY BW
5.RETURN

Security IR Camera User’s Manual
24
Security IR Camera User’s Manual
25
MAIN SETUP
1. BRIGHTNESS AUTO
2. CONTRAST MANUAL
3. RANGE AUTO
4. NUC
5. NUC MOOE INTERVAL
6. IMAGE ADJ
7. SPECIAL
8. SAVE
POLARITY”toswitchtheblack/whiteinversionsettingfrom:BWWBBW.Select“5.
RETURN”toconfirmthecurrentsettingandgobacktotheMAINSETUPmenuscreen.
(Defaultvalue:BW)
  -THLo:SettheLRangethreshold.
  -THHi:SettheHRangethreshold.RETURNConfirmthecurrentsettingandgobacktothe
IMAGEADJsubmenuscreen.
Usethismenutoadjustenvironmentsettingsitemsrelatedtoareassuchasscreendisplay,video
output,andcommunications.PresstheSETbuttonwhilethecursorisalignedwith“7.SPECIAL”to
display the following sub menu.

TVSYSTEM(videooutputsetting):
  Usethisoptiontoadjustthevideooutputsetting.
  PresstheLEFTbuttonorRIGHTbuttonwhilethecursoris
alignedwith“1.TVSYSTEM”toswitchtheTVSYSTEM
settingfrom:NTSC  PAL  NTSC.Select“5.RETURN”
to confirm the current setting and go back to the MAIN
SETUPmenuscreen.(Defaultvalue:NTSC)

COMMADJ(communicationsettingsmode):
  Usethismenutoadjustcommunicationsettings.
  PresstheSETbuttonwhilethecursorisalignedwith“3.
COMMADJ”intheSPECIALSETUPmenutodisplaythe
following sub menu.

CAMERAID(cameraIDsettings):
  UsethisoptiontoadjustCAMERAIDsettings.
  PresstheLEFTbuttonorRIGHTbuttonwhilethecursorisalignedwith“1.CAMERAID”to
adjusttheCAMERAIDsettingtoavaluefrom0-255.Theadjustedvaluewillbecomevalid
whenthesettingissaved.Select“6.RETURN”togobacktotheSPECIALSETUPmenu
screen.(Defaultvalue:0)

BAUDRATE(communicationsspeedsettingsmode):
  UsethisoptiontochangetheBAUDRATEtooneoffoursettings:38,400bps,19,200bps,
9600bps,4800bps.PresstheLEFTbuttonorRIGHTbuttonwhilethecursorisalignedwith
“2.BAUDRATE”toswitchtheBAUDRATEsettingfrom:4800  9600  19,200  38,400
 4800.Select“6.RETURN”toconfirmthecurrentsettingandgobacktotheSPECIAL
SETUPmenuscreen.(Defaultvalue:9600bps)

UARTMODE(paritysettingsmode):
  Usethisoptiontoadjustparitysettings.
  PresstheLEFTbuttonorRIGHTbuttonwhilethecursorisalignedwith“3.UARTMODE”to
switchtheUARTMODEsettingfrom:8-E-1  8-O-1  8-N-1  8-E-1.Pleasenotethat
boththebitlength(8)andthestopbit(1)arefixed.Select“6.RETURN”toconfirmthecurrent
settingandgobacktotheSPECIALSETUPmenuscreen.(Defaultvalue:8-E-1)

RETPKT(returnpacketsetting):
  Usethisoptiontoadjustthereturnpacket(returnedusingthesamestatusasthedata
entered) setting.
  PresstheLEFTbuttonorRIGHTbuttonwhilethecursorisalignedwith“4.RETPKT”toswitch
theRETPKTsettingfrom:ON  OFF  ON.Select“6.RETURN”toconfirmthecurrent
settingandgobacktotheSPECIALSETUPmenuscreen.(Defaultvalue:ON)

CameraID(IDdisplaysetting):
  UsethisoptiontoadjustthedisplaysettingofthecurrentlysetCameraID(appearsonthetop
left of the screen).

POLARITY:
Use this option to set the black/white properties of images.
When“BW”isselected,hightemperatureareaswillbe
shown in white, while low temperature areas will be
displayedinblack.If“WB”ischosen,blackandwhitewill
bedisplayedintheoppositewayasBW.PresstheLEFT
buttonorRIGHTbuttonwhilethecursorisalignedwith“4.
Operating the Camera
SPECIAL (environment settings mode)
IMAGE ADJ
1.3D-DNR OFF
2.SHARPNESS OFF
3.D-ZOOM X2
▶ 4.POLARITY BW
5.RETURN
SPECLAL SETUP
▶ 1.TV SYCTEM NTSC
2.LANGUAGE ENGLISH
3.COMM ADJ
4.RESET
5.RETURN
COMM ADJ
1.CAMERA ID 1
▶ 2.BOUDRATE 4800
3.URAT MODE 8-E-1
4.RET PKT ON
5.DISPLAY CAM ID OFF
6.RETURN

Security IR Camera User’s Manual
26
Security IR Camera User’s Manual
27
SPECLAL SETUP
1.TV SYCTEM NTSC
2.LANGUAGE
3.COMM ADJ
▶ 4.RESET
5.RETURN
MAIN SETUP
1. BRIGHTNESS AUTO
2. CONTRAST MANUAL
3. RANGE AUTO
4. NUC
5. NUC MOOE INTERVAL
6. IMAGE ADJ
7. SPECIAL
8. SAVE
9. EXIT
MAIN SETUP
1. BRIGHTNESS AUTO
2. CONTRAST MANUAL
3. RANGE AUTO
4. NUC
5. NUC MOOE INTERVAL
6. IMAGE ADJ
7. SPECIAL
8. SAVE
9. EXIT

RESET(Reset):
Use this option to restore each item to its default setting.
  PresstheSETbuttonwhilethecursorisalignedwith“4.RESET”torestoreeachitemtoits
factorydefaultsetting.Pleasenote,however,thatneitherTVSYSTEMnorCOMMADJcanbe
changed.Select“5.RETURN”togobacktotheSPECIALSETUPmenuscreen.
Use this option to save device settings and establish the basic settings which will be used the next
timeyoustartupthedevice.PresstheSETbuttonwhilethecursorisalignedwith“8.SAVE”to
recordyourcurrentsettingstotheinternalmemory.Ifyouexitwithoutsaving,theMAINSETUP
menu will close without any values being updated.
  PresstheLEFTbuttonorRIGHTbuttonwhilethecursorisalignedwith“5.DISPLAYID”to
switchtheCAMERAIDdisplaysettingfrom:ON  OFF  ON.Select“6.RETURN”toconfirm
thecurrentsettingandgobacktotheSPECIALSETUPmenuscreen.(Defaultvalue:OFF)
PresstheSETbuttonwhilethecursorisalignedwith“9.EXIT”toclosetheMAINSETUPmenu.
①
AfterswitchingBRIGHTNESSand/orCONTRASTtoMANUALandsavingyourchanges,images
maynotbedisplayedthenexttimeyourestartthedevice.Torenderimagesinsuchacase,set
BRIGHTNESSand/orCONTRASTto“AUTO”orreadjusttheMANUALsetting.
②
If you save after changing the RS485 communications CAMERA ID, the ID will then be set/stored.
If the CAMERA ID was set incorrectly, exit without saving.
Operating the Camera
SAVE
EXIT (close menu)
• Do not disengage the power while settings are being saved.
Notes

Security IR Camera User’s Manual
28
Security IR Camera User’s Manual
29
Item Specification Comment
Sensor
Detector (sensor)
format Uncooled model
Sensor pixels 320(H)×240(V)
Sensor pitch 23.5μm
Measured
wavelength range 8 ~ 14μm
Minimum detection
temperature 80mK Minimum detection temperature
Sync
Video ratio 30 Frame / Sec (NTSC)
25 Frame/Sec(PAL)
Video data output at 30 frames
per second (NTSC Mode)
Video output VBS : 1.0VP-P,75Ω composite (NTSC or PAL)
Synchronous model Internal
Function
OSD English/Korean/Japaness
Noise reduction
function Adjustable over four levels
Polarity function BW/WB (256 levels displayed)
Set either black or white to
display subjects containing
high temperatures
Brightness/contrast
adjustment
Each adjustable over 11 levels
(AUTO/MANUAL: ten levels)
Temperature range AUTO/MANUAL (two levels) Monitored area temperature
range setting
Sharpness Adjustable over six levels
lens
Built-in lens f:14mm, F:1.4
Focus distance
(focus range/
adjustment)
(At time of shipment: adjusted before shipment)
IFOV(Instantaneous
field of view) 1.68mrad
Viewing angle (H × V) 30.1° × 22.8°
Zoom Digital zoom function (2×, 4×)
Communications specifications RS485 control
Samsung Techwin Protocol, backup OSD control function
Input voltage AC24V,50/60Hz
Electricity consumption Approx. 10.5 W (22 W when heater is being
operated)
Operating temperature (Heater automatic operation)
Storage temperature -40  ~ +70 
Outer diameter size 104(W) X 123(H) X 352(D) mm
Dustproof/waterproof
protection rating IP66
Weight Approx. 2.2 kg (including cables)
*Althoughtheinfraredsensorhasbeenbuiltusinghigh-precisiontechnology,pleaseunderstandthatthere
may be times when pixels may be lost, or remain stuck/flashing. Also, be aware that continuously monitoring
ahightemperatureobjectbeyondacertainperiodoftimemayproduceanafterimage.
* In cases where the product installation site experiences a sudden change in temperature (dropping by 15°C
ormore),thecamera’sfocuswillbecomeblurredwithregardstosubjectslocatedwithinthreemeters.
Specifications
* RS485 Communication Settings Default Values
Item Camera No. Communications
Speed
Communications
Mode Data Reception
Default Value 19600 8-EVEN -1 In use
Check the points listed below if the product appears to be malfunctioning. If the problem
continues, please contact the sales agent from whom the product was purchased.
• If nothing can be seen onscreen :
 -Verifythatthepowersourceisconnectedproperly,andthatthedeviceisreceivingpower.
-Verifythatthevideosignalwireisconnectedproperly.
• If screen images do not appear clearly :
 -Wipethelenswithacleanclothorbrushtoremoveanydustthatmaybepresent.
 -Adjustthestatusofthemonitor.
-Changethepositionorangleofthecameraifalargeamountofbrightlightisdisplayedonscreen.
• If the screen is too dark :
 -Adjustthestatusofthemonitor.
 -Verifythatintermediateprocessingcanbeperformedproperlybetweensystems.
• If the camera is operating abnormally, or its surface is very hot, causing black lines to appear
onscreen :
 -Verifythatthepowervoltagereceivedbythecameraconformstotheproperrating.Also,confirm
whether performance is affected by the time of day.
• If RS485 communications cannot be carried out :
 -VerifythepolarityoftheRS485communicationsterminalandthearrangementofthecables.
 -VerifytheRS485communicationssettings.
Troubleshooting

Security IR Camera User’s Manual
30
Security IR Camera User’s Manual
31
Ø104 352
123 104
DECLARATION OF CONFORMITY
Application of Council Directive(s) 89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
European Representative Name
European Representative Address
Equipment Type/Environment Security IR Camera
Model Name SDC-425P, SDC-425PH, SDC-425PD
Beginning Serial NO. S8030001
Year of Manufacture 2009. 03. 01
Conformance to EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe
Signature Signature
Full Name HAN SEUG KIM Full Name
Position QUALITY CONTROL MANAGER Position
Place CHANGWON, KOREA Place
Date 2009. 03. 01 Date
Dimension