Samsung SVD4600 Series User manual

High Resolution Vandal-proof Dome Camera SVD-4600 User Guide
Before installing and operating this product,
please read this manual thoroughly.
ENGLISH

This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer
could void the user ’ s authority to operate the equipment.
WARNING - To prevent electric shock and risk of fire hazards:
◆Do NOT use power sources other than that specified.
◆Do NOT expose this appliance to rain or moisture.
Before operating the camera, confirm the camera model and proper input power
voltage. In order to that you can understand this manual thoroughly, we'll introduce our
model description.
n SVD-4600 SERIES
 •NTSCMODEL •PALMODEL
 SVD-4600(W)N SVD-4600(W)P
nMODEL DESCRIPTION
 •SVD-4600(W)X
_ _
 •SIGNALSYSTEM
  NNTSCMODEL
  PPALMODEL
 •CAMERACOLOR
SILVERCOLOR
  WIVORYCOLOR
SIGNALSYSTEM
CAMERACOLOR

COLOR CCD CAMERA User Guide
4
COLOR CCD CAMERA User Guide
5
• Precautions …………………………………………………………………… 7
• Components and Accessories …………………………………………… 9
• Overview ………………………………………………………………………… 9
• Connection ……………………………………………………………………… 10
nConnectingToMonitor
  
nConnectingToPower  
nRS-485communicationcontrol  
• Operating Your Camera …………………………………………………… 13
nMenuConfiguration
 

nMenuSetup
  
 •LENS 
 •EXPOSURE  
 •WHITEBALANCE 
 •BACKLIGHT 
 •SSNR  
 •DAY/NIGHT  
 •IMAGEADJ   
 •SPECIAL  
 •EXIT  
• Troubleshooting …………………………………………………………… 29
• Specification ………………………………………………………………… 30
• Dimension …………………………………………………………………… 30
Contents Features
Excellent Sensitivity
Adoptinga Diagonal 6mm(1/3"),highly sensitiveCCD and
digital signal processing technology, it can clearly
distinguish the outline and color of a subject in an
extremely low luminance environment – even, for example,
understarlight.Since surveillanceispossiblein places
where the light is poor, the camera is appropriate for day
and night surveillance outdoors or on the outside of
buildings.
-0.00004Lux
Day & Night
The camera identifies whether it is day or night and
automatically switches to the appropriate mode, depending on
its environment. By day, the camera switches to color mode in
orderto maintainoptimalcolor.Atnight,it switchesto B/W
mode so as to obtain better picture definition.
DIS (Digital Image Stabilizer)
TheDISfunctioncompensatesforanycamera
movement, to produce more stable pictures.
Sub Monitor Function
The sub monitor function enables easy adjustment of the
camera angle within the monitoring range during its installation.
IP66 Approved /
Dust & Rain Resistant
Withdustandrainresistantdesign,thecameracanbe
installed ouside under building eaves or place that is
esposed to the dust and rain.
Miscellaneous Functions
SYNC(INT/LL),SENS-UP, FREEZE,FLIP(H/V-REV),
D-ZOOM,SHARPNESS,MOTIONDETECTIONand
PRIVACYfunctionsareprovided.
RS-485 Communication
Control Support
RemoteOSDmenucontrolviaanRS-485interfaceissupported.
OSD
The camera control is convenient by using 9 different
foreignlanguageO.S.D.
-NTSC:Korean,English,Spanish,Japanese,French,Portuguese
-PAL:English,French,German,Spanish,Italian,Chinese,Portuguese
Wide Dynamic Range (WDR):
ByadoptingaproprietarySV-IVDSPchip,thecameradelivers
clear, high quality pictures even in backlight, by increasing
exposure in dark areas while decreasing it in bright areas; a
corrected image with clear details results.
SSNR (Samsung Super Noise
Reduction) Function
ThehighperformanceSV-IVDSPchip
dramatically reduces the gain noise in digital
image processing, producing clear, sharp images
in low lighting environments.
Ultra High Resolution
Byadopting adouble-speed410,000pixelSonyCCD,the
camera produces clear picture quality with a horizontal
resolutionof560TVlinesforcolor,and700TVlinesforB/W.
Vari-focal Lens Built-in
With built-in vari-focal lens, the camera can control the focal
distanceeasilyfrom2.8to10.0mm.

COLOR CCD CAMERA User Guide
6
COLOR CCD CAMERA User Guide
7
SamsungTechwincaresfor theenvironmentat allproductmanufacturing
stages to preserve the environment, and is taking a number of steps to provide
customerswithmoreenvironment-friendly products.The Eco markrepresents
SamsungTechwin’swilltocreateenvironment-friendlyproducts,andindicates
thattheproductsatisfiestheEURoHSDirective.
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise.Pleasereaditcarefullyandusetheproductaccordingly.
Warnings & Cautions
 *Forproductinquiries,pleasecontacttheretailshopwhereyouboughtthecamera.Theuseofequipmentsuchas
anaerialladderwhileprovidingafter-salesserviceshallbeatyourexpense.
 *Separatethepowerplugwhenthundercrashesorlightingflashes.
 *Thisproductissupportequipmentforsurveillancesystem.Therefore,wecan'tcompensateformateriallossand/or
personal injuries by robbery, fire, natural disaster or something like this type.
Ignoring this information may
resultinmateriallossand/or
serious personal injuries including
death.
Indicates“NeverAllowed.”
Ignoring this information may
resultinmateriallossand/ora
slight injuries.
Indicates“NoDisassembling.”
Do not install the camera in
extreme temperature conditions.
Onlyusethecameraunderconditions
where temperatures are between
-10ºC and +50ºC. Be especially careful
to provide ventilation when operating
under high temperatures.
Do not install or use the camera in an
environment where the humidity is high.
It can cause the image quality to be
poor.
Do not install the camera under
unstable lighting conditions.
Severelightingchangeor flickercan
cause the camera to work improperly.
Do not touch the front lens of the
camera.
It is one of the most important parts of
the camera. Be careful not to be
stained by fingerprint.
Precautions
Warning/Attention/Special Mark Messages

COLOR CCD CAMERA User Guide
8
COLOR CCD CAMERA User Guide
9
Do not drop the camera or subject
them to physical shocks.
It can cause malfunctions to occur.
Never keep the camera face to
strong light directly.
•If thecameraisexposed tospotlightorobjectreflectingstrong light,smearor
blooming may occur.
•Pleasecheckthatthe power satisfies the normal specification before connecting
the camera.
Notes
ItcandamagetheCCD.
Do not expose the camera to
radioactivity.
If it isexposedtoradioactivity,For
heatedCCD,itwillbeoutoforder.
Precautions
❶ SVD-4600

2 Instruction Manual

3 M5 Tapping Screw 4EA

4 Quick Install Guide

5Wrench

6 Template

7
 Installation Video Output Cable
❶5
67
2 4
Components and Accessories
876
4
⓬⓫23
5
9❿
1
Overview
3

COLOR CCD CAMERA User Guide
10
COLOR CCD CAMERA User Guide
11
❶ Pan Base
: control panning angle of camera
2 Rotate Base
: control rotating angle of camera
3 X3.6 Vari-focal Lens Module
4 Rotate Base Holding Screw
: fix rotated position
5 Pan Base Holding Screws (Color : Silver)
: fix panned position
6 RS-485 Control Cable
: The detailed description refers to p12
7 Power Input Jack

8 Video Output Jack
9 Function Setup switch
: display the menu on the screen and move the cursor to four
directions to confirm status or after changing a selected item.
❿Video Output Terminal to Monitor

⓫Dome Cover
⓬Shield Case
Overview
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
Connection
Monitor
CCTVCamera
CCTVCamera
Intermediate Endmonitor
Connect the adaptor to the power input
connector as shown in the figure below.
The recommended adaptor specification
for SVD-4600 is AC 24V / 500mA or DC 12V
/ 500mA.
power input terminal
• As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an
excessively long adaptor output line for connection to the camera may affect the
performance of the camera.
*Standard voltage for camera operation : DC 12V ± 10%,AC 24V±10%
*There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
•Besuretoconnectpoweronlyafteralltheinstallationiscomplete.
•UsetheULlisted,class2powertransformerofAC24Vadaptor.
•GroundshouldbeconnectedtotheGNDterminal.
Notes
When the resistance value of copper wire is at [20ºC(68°F)]
Copper wire size (AWG) #24(0.22㎟)#22(0.33㎟)#20(0.52㎟)#18(0.83㎟)
Resistance (Ω / m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.078 0.018 0.011 0.006
Connecting to Monitor
Connecting to Power
• As the connecting method varies with the instruments, refer to the manual supplied with the
instrument.
• If necessary, you can connect the monitor to the REMOTE jack on the back of your camera.
• Only connect the cable when the power is turned off.
• Set the 75Ω/ Hi-Z selection switch as shown below if you have an intermediate device.

COLOR CCD CAMERA User Guide
12
COLOR CCD CAMERA User Guide
13
Using a RS-485 communication, it will be able to control the OSD menu at the
SAMSUNG TECHWIN System Controller or DVR.
(1) The case which it controls from the PC
Using a RS-485 converter, It connects to RS-485 control cable outside camera
and serial cable
EX) SERIAL PORT OF THE PC(COM1) → SERIAL CABLE → RS-485 CONVERTER → RS-485
CONTROL CABLE
(2)The case which it controls from the DVR or System Controller
It connects the RS-485 control cable in the connection terminal of 485 control
boards which are connected with the DVR or System Controller.
Connecting to RS-485 Control Cable
•Whenyouconstructexternalcontrolsystemsforacameracontrol,pleaseusetotheSAMSUNG
TECHWINPROTOCOLorPELCO-DPROTOCOL.
•WhenyouconnectingtoRS-485controlcable,pleasepeelofftheouterskininsidetheRS-485
control cable.
•IncaseofSCC-101connection,changecommunicationmodeto  8-E-1  at  Communication
configuration  menu.(Formoreinformation,refertoSCC-101manual.)
Notes
* RS-485 Communication establishment initial value
Connection
485 Control Board Connection Port RS-485 Control Port
(+) CONNECTION TERMINAL RED (TRX+)
(-) CONNECTION TERMINAL WHITE (TRX-)
CONTROL CABLE SPEC
RED (TRX+) RS-485+
WHITE(TRX-) RS-485-
Item Camera ID BAUD RATE UART MODE RET PKT
Initial value 19600 8-NONE-1 ENABLE
Setup Menu
LENS
 DC
EXPOSURE
 SHUTTER  AGC   SENS-UP 
 RETURN 
WHITE BALANCE
 ATW  MANUAL  AWC→SET 
 OUTDOOR  INDOOR
BACKLIGHT

OFF

WDR

BLC

HLC
SSNR

ON

OFF
DAY/NIGHT

COLOR

B/W

AUTO
IMAGE ADJUSTMENT
(IMAGE ADJ.)

FREEZE

V-REV
 
H-REV


D-ZOOM

SHARPNESS
 
RETURN
SPECIAL

CAMTITLE

SYNC
 
MOTION DET

PRIVACY

DIS
 
COMM ADJ


LANGUAGE

RESET

RETURN
EXIT
Operating Your Camera
Use the Function Setup switch on back of the camera.
FunctionSetupswitch
RS-485 communication control
Menu Setup
Menu Configuration

COLOR CCD CAMERA User Guide
14
COLOR CCD CAMERA User Guide
15
1. Press the Function Setup switch.
• Main setup menu is displayed on the monitor screen.
2. Select a desired function using the Function Setup switch.
• Place the cursor over a desired item.
Operating Your Camera
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
Using this function, you can control screen brightness.
1. When the SETUP menu screen is displayed, select 'LENS' by using the Function
Setup switch so that the arrow indicates 'LENS'.
LENS
•Anitemwiththe icon also has sub menus. To select a sub menu, select an item
withtheiconandpresstheFunctionSetupswitch.
•Anitemwiththe---iconisunavailableduetofunctionsettings.
Notes
Selectthefunctionbymoving
up or down direction of
function setup switch.
Changethestatusby
moving right or left
direction of function setup
switch.
SHUTTER : Because of using a DC lens, the shutter speed is fixed.
(NTSC mode l: 1/60 sec, PAL model : 1/50 sec)
When flickering occurs on the screen, select the A.FLK mode using the
Function Setup switch.
- A.FLK : Select this when you experience picture flicker, which can happen when there is a
clash with the frequency of the installed lighting.
•To producebetterresults withA.FLK, do notuseit in conjunctionwiththeWDR
modeoftheBACKLIGHTmenu.
•WhentheSHUTTERissettoA.FLKmode,SENS-UPwillbedisabled.
Notes
DC : Select Auto Iris Lens
• When DC is selected, you can control screen
brightness. The range of brightness control is
between 1 and 70. Adjust the brightness
appropriately for optimal screen brightness.
1. When the SETUP menu screen is displayed, select
'EXPOSURE' by using the Function Setup switch so that
the arrow indicates 'EXPOSURE'.
2. Select a desired mode using the Function Setup switch.
EXPOSURE
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
9.EXIT
MAIN SETUP
1.LENS DC
2.EXPOSURE
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW

COLOR CCD CAMERA User Guide
16
COLOR CCD CAMERA User Guide
17
Operating Your Camera
AGC (AUTO GAIN CONTROL) :
The higher the gain level, the brighter the screen - but the higher the noise.
- OFF : Deactivates the AGC function.
- LOW :Allows automatic gain control from 5.3dB to 30dB.
- HIGH :Allows automatic gain control from 5.3dB to 42dB.
SENS-UP :
When it is night or dark, the camera automatically detects the light level and
maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO :Activates the SENS-UP function.
RETURN :
Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.
•IfyoupresstheFunctionSetupswitchin‘AUTO’mode,Youcanadjustbrightnessby
increasingordecreasingtheshutterspeed.(x2~x256)
•Notethatthehigherthezoomlevel,thebrighterthescreen,butthemorelikelyitis
thatanafter-imagewillappear.
•AlthoughNoise,Spots,andWhitishsymptoms mayoccurin SENS-UPoperation
when the zoom level is increased, this is normal.
Notes
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ‘White Bal.’ by using the
Function Setup switch so that the arrow indicates ‘White Bal.’ .
2. Select a desired mode using the Function Setup switch.
Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1,800ºK and 10,500ºK
INDOOR : Select this when the color temperature is between 4,500ºK and 8,500ºK.
OUTDOOR : Select this when the color temperature is between 1,800ºK and 10,500ºK.
(sodium light inclusion)
AWC →SET : To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press
the Function Setup switch. If the environment changes, readjust it.
White Balance (White Bal.)
MANUAL : Select this to fine-tune White Balance
manually. Set White Balance first by using the
ATW or AWC mode. After that switch to
MANUAL mode, fine-tune the White Balance
and then press the Function Setup switch.
•WhiteBalancemaynotworkproperlyunderthefollowingconditions.Inthiscase
selecttheAWCmode.
❶Whenthecolortemperatureofenvironmentsurroundingthesubject isout ofthe
control range (e.g. clear sky, or sunset)
2Whentheambientilluminationofthesubjectisdim.
3
If the camera is directed towards a fluorescent light or is installed in a place
whereilluminationchanges dramatically, theWhiteBalanceoperation may
become unstable.
Notes
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF

COLOR CCD CAMERA User Guide
18
COLOR CCD CAMERA User Guide
19
This camera is designed so that it delivers a distinctive subject and background at
the same time, even when the subject is in backlight, unlike conventional cameras,
by adopting a proprietary SV-IV DSP chip.
1. When the SETUP menu screen is
displayed, select ‘BACKLIGHT’ by using the
Function Setup switch so that the arrow
indicates ‘BACKLIGHT‘.
2. Select a desired mode using the Function
Setup switch depending on the camera
purpose .
Operating Your Camera
BACKLIGHT
OFF : Not being used.
3. Select a desired mode using the Function Setup switch and press the SET button.
WDR OFF
• Select ‘WDR’ to adjust the WDR LIMIT and LEVEL.
HLC(High Light Compensation) :
If the scene contains extremely bright light areas such as; from car headlight,
the light can mask out much of the on-screen detail.
- DAY : in normal daylight conditions, the HLC is not activated.
- NIGHT : lf a high light that is larger than a certain size is present on the screen,
HLC is activated to remove the high light.
- HLC : Enable a user to select a mask color of high light area from a picture.
- LIMIT : Adjust the WDR Sensitivity by selecting LOW,
MIDDLE, or HIGH.
- LEVEL : Adjust the WDR Brightness by controlling the
bar from 1 to 100.
• The WDR compensates for backlight more effectively than previous models,
by applying an optimum fusion ratio when combining the high speed shut
ter used in bright areas and the low speed shutter used in dark areas.
•Sincethefollowing symptomsmayoccur accordingto the ambientillumination when
WDRisselected,setittoOFF.
❶Colororscreenchangesunnaturally.
2Noiseappearsinthebrightpartofthescreen.
•SincetheperformanceoftheWDRfunctionmaybeaffectedbytheareaofthebrightpart
ofthescreen,optimizetheinstallationangleforthebestWDRperformance.
•IfyouincreaseLIMIT,thescreendisplaymaybedistorted.
•In adark environment,theHLCis onlyactivated whena highlightthat islarger thana
certain area is present.
•TheHLCisnotactivatedinlightoroverlydarkconditions.
Notes
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
BLC : Enables a user to directly select a desired area
from a picture, and to view the area more clearly.
• Select ‘BLC’ to adjust the area to be enhanced and
enhancement level.
WDR : When there are both bright and dark areas at
the same time, this mode makes both areas
distinctive.

COLOR CCD CAMERA User Guide
20
COLOR CCD CAMERA User Guide
21
Operating Your Camera
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select ‘SSNR’ by using the Function
Setup switch so that the arrow indicates ‘SSNR’ .
2. Select a desired mode using the Function Setup switch.
OFF : Deactivates SSNR. Noise is not reduced.
ON : Activates SSNR so that noise is reduced.
SSNR
3. Set the SSNR mode to ‘ON’ and press the Function Setup switch. Then you can
adjust the noise reduction level.
•YoucannotsettheSSNRto‘ON’or‘OFF’whentheAGCmodeoftheEXPOSURE
menuis‘OFF’.
•WhenadjustingthenoisereductionleveloftheSSNRmode,rememberthatthe
higher the level set, the more the noise level will be reduced but that after image
may also occur.
Notes
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the
Function Setup switch so that the arrow indicates ‘DAY/NIGHT’.
DAY/NIGHT
2. Select a desired mode using the Function Setup switch according to the picture
display you want.
COLOR : The picture is always displayed in color.
B/W : The picture is always displayed in black and
white. Please press SETUP button to turn on
or off the burst signal on B/W mode.
AUTO : The mode is switched to ‘Color’in a normal
environment, but switches to ‘B/W’mode
when ambient illumination is low. To set up
the switching time or speed for AUTO mode,
press the Function Setup switch.
- DWELL TIME : You can select the duration time about
changing the day/night mode.
 5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
- DURATION : You can select brightness of illumination about changing the
day/night mode.

COLOR CCD CAMERA User Guide
22
COLOR CCD CAMERA User Guide
23
• YoucannotcontroltheDAY/NIGHTmenuwhenAGCintheEXPOSUREmenuis‘OFF’.
Atthistime,theexchangebetweenDAYmodeandNIGHTmodeoperatesaslike
selecting‘COLOR’mode.
•TheOSDkey doesnot work for3 seconds whenswitching toColoror B/W, to
ensure stable camera operation.
• The camera may focus less well under infrared illumination than under normal illumination.
Notes
EXTERN : This mode allows you to apply a desired filter to external signals.
* The brightness of illumination is changeable
by installed environment.
Operating Your Camera
2. Select a desired mode using the Function Setup switch.
1. When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the
Function Setup switch so that the arrow indicates ‘IMAGE ADJ.’
IMAGE ADJ.
FREEZE : You can view still or moving pictures.
V-REV : You can flip the picture vertically on the
screen.
H-REV : You can flip the picture horizontally on
the screen.
D-ZOOM : You can use a digital zoom of x2~x10.
SHARPNESS :
As you increase this value, the picture outline
becomes stronger and clearer. Adjust this value
appropriately depending on the sharpness of
the picture.
PED LEVEL : Please use this menu item when
using a LCD monitor other than
standard ones. You can change
PED LEVEL.
RETURN : Select this to save the settings for the IMAGE ADJ. menu and to
return to the SETUP menu.
•WhentheV-REVorH-REVmodeisenabled,thetextonthescreendoesnotflip.
•IfyouincreasetheSHARPNESSleveltoohigh,thepicturemaybecomedistortedor
noise may appear.
Notes
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
IMAGE SETUP
1. V-REV OFF
2. H-REV OFF
3. D-ZOOM OFF
4. SHARPNESS ON
5. PED LEVEL 0
6. RETURN
Color B/W B/W Color
Fast 2.5 lux 4 lux
Slow 0.8 lux 6 lux

COLOR CCD CAMERA User Guide
24
COLOR CCD CAMERA User Guide
25
Operating Your Camera
1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function
Setup switch so that the arrow indicates ‘SPECIAL’.
SPECIAL
CAM TITLE : If you enter a title, the title will appear on the monitor.
❶
If the SPECIAL menu screen is displayed, use the Function Setup switch so
that the arrow indicates ‘CAM TITLE’.
2
Set it to ‘ON’by using the Function Setup switch.
･WhentheCAMTITLEmenu is･OFF･, no
title will be displayed on the monitor screen
even if you enter one.
Notes
•WhentheCAMTITLEmenuis‘OFF’,notitle
will be displayed on the monitor screen
even if you enter one.
Notes
3
Press the Function Setup switch.
4
Use the Function Setup switch to move to a desired letter and select the letter
by pressing the Function Setup switch. Repeat this to enter multiple letters.
You can enter up to 15 letters.
•IfyoumovethecursortoCLRandpresstheFunctionSetupswitch,alltheletters
are deleted. To edit a letter, change the cursor to the bottom left arrow and press
theFunctionSetupswitch.Movethecursoroverthelettertobeedited,movethe
cursortothelettertobeinsertedandthenpresstheFunctionSetupswitch.
Notes
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
CLR POS END
5 Enter a title, move the cursor to ‘POS’ and press
the Function Setup switch. The entered title
appears on the screen. Select the position to
display the title on the screen by using the
Function Setup switch and press. When the
position is determined, select ‘END’ and press the
Function Setup switch to return to the SPECIAL
menu.
FRONT DOOR
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
9.EXIT
SPECIAL
1. CAM TITLE OFF
2. SYNC INT
3. MOTION DET OFF
4. PRIVACY OFF
5. DIS OFF
•OnlyEnglishisavailableinthismode.
SPECIAL
1. CAM TITLE OFF
2. SYNC INT
3. MOTION DET OFF
4. PRIVACY OFF
5. DIS OFF
6. COMM ADJ
7. LANGUAGE ENGLISH
8. RESET
9. RETURN
2. Select a desired mode using the Function Setup switch.

COLOR CCD CAMERA User Guide
26
COLOR CCD CAMERA User Guide
27
Operating Your Camera
❶
When the SPECIAL menu screen is displayed, press the Function Setup
switch so that the arrow indicates ‘MOTION DET’.
2
Set up the mode using the Function Setup switch.
MOTION DET:
You can monitor activity more efficiently, because a
signal is generated by the camera whenever
motion is detected.
• WhenusingACpowerat60Hzfrequency,youcanusetheL/Ltypesynchronization.
•WhenthepowerisDC12V,theSYNCmenuisfixedtothe‘INT’mode.
Notes
PRIVACY : Hide an area you want to hide on the
screen.
❶
  When the SPECIAL menu screen is displayed,
press the Function Setup switch so that the
arrow indicates ‘PRIVACY’.
2
Set up the mode using the Function Setup
switch.
- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high,
motion detection sensitivity is increased to recognize even small
movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- FILL SET : Fills in a selected MD area. Fills in a selected MD area.The color of filling
is sequentially selected as brown, orange, blue, cyan, yellowish green,
yellow and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL
menu.
• MDareasshowonlyMOTIONDETmenu.Therefore,MDareasdon’tdisplayonthe
monitor screen.
• Whenmotionisdetected,“MOTIONDETECTION”expressionisdisplayedonthescreen.
Notes
- AREA SEL : You can select up to 8 PRIVACY areas.
- AREA MODE : Determines whether to use the area
selected in the AREA SEL, and the
size and position of the area.
- MASK COLOR : Determine area color. You can select Gray, Green, Red, Blue, Black,
White.
- TRANSP : Determine the transparency of selected area as controlling number
from 0 to 3.
- RETURN : Select this to save the PRIVACY menu settings and return to the
SPECIAL menu.
DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as
wind.
• ThechanceofresolutiondecreaseisexistedbecauseDISfunctionusesthedigitalzoom.
• DISdoesn’toperatewhenbackgroundilluminationistoolow.
• DISdoesn’toperatewhenobjectpatternismonotonicaslikeskyorwhitewall.
•IfDISisenabled,thedigitalzoomisconfiguredtolessthan46level.
Notes
SYNC :
In areas where the supply is at 60Hz, you can
synchronize the output phase of multiple cameras
using the power synchronization function (Line-
Lock) without using a synchronization signal
generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
• Press the Function Setup switch.
• You can select a desired phase from 0 to 359 when select 'phase'.
• You can decide the synchronization between luminance and color signal when
select the 'Mode' to TRACE.

COLOR CCD CAMERA User Guide
28
COLOR CCD CAMERA User Guide
29
485 Control Board Connection Port RS-485 Control Port
(+) CONNECTION TERMINAL (TRX+) 485+
( - ) CONNECTION TERMINAL (TRX-) 485-
Press the Function Setup switch in the EXIT menu to save the current settings and exit the
MAIN SETUP menu.
EXIT
LANGUAGE : You can select the menu language according to your
requirements.
RESET : Resets the camera settings to the factory defaults.
RETURN :
Select this to save the SPECIAL menu settings and return to the MAIN SETUP
menu.
- CAM ID : Determines the camera's identification number (between 0 and 255).
- BAUD RATE :You can select 2400/4800/9600/19200/38400/57600 bps.
- UART MODE :You can select NONE, EVEN or ODD for the parity bits.
- RET PKT : Determines whether to send a command back to the controller device
when a communication control command is sent to the camera.
- DISP CAM ID : Display camera title on top left corner of the screen.
COMM ADJ (Communication Adjustment) :
This function sets up the camera communication status when controlling the
camera through an external control device.
❶
When the SPECIAL menu screen is displayed, press the Function Setup
switch so that the arrow indicates ‘COMM ADJ’.
2
Set up the mode using the Function Setup switch.
* Initial value of communication adjustment
Operating Your Camera Troubleshooting
●
Nothing appears on the screen.
▶ Check that the power cord and line connection between the camera and monitor are fixed properly.
▶ Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
● The image on the screen is dim.
▶ Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶ Set the monitor to proper condition.
▶ If the camera is exposed to too strong light, change the camera position.
● The image on the screen is dark.
▶ Adjust the contrast feature of the monitor.
▶ If you have an intermediate device, set the 75Ω/ Hi-z properly.
● The camera is not working properly, and the surface of the camera is hot.
▶ Check that you have properly connected the camera to an appropriate power source.
● The DAY/NIGHT menu does not work.
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
● The SENS-UP function does not work.
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶ Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ .
● The Motion Detection function does not work.
▶ Check that MOTION DEF of SPECIAL SETUP menu is ‘OFF’.
● Color is not correct.
▶ Check the setting of WHITE BAL SETUP menu .
● The screen flickers continually.
▶ Check that direction of camera turns toward the Sun.
● RS-485 communication fails.
▶ Check the polarity between RS-485 Control Port and RS-485 cable.
▶ Check the RS-485 Communication establishment initial value
▶ We recommend that you make ground connect between camera and controller in order to maintain
safety communication control.
Refer to the following table if you are experiencing trouble with your camera.
Contact an authorized technician if the table does not provide you with a
solution to the trouble.
* RS-485 Communication establishment initial value
Item Camera ID BAUD RATE UART MODE PET PKT
Initial value 19600 8-NONE-1 ENABLE
Item Camera ID BAUD RATE UART MODE RET PKT
Initial value 19600 8-NONE-1 ENABLE

COLOR CCD CAMERA User Guide
30
COLOR CCD CAMERA User Guide
31
Specifications DECLARATION OF CONFORMITY
ApplicationofCouncilDirective(s) 89/336/EEC
Manufacturer'sName SAMSUNGTECHWINCO.,LTD
Manufacturer'sAddress SAMSUNGTECHWINCO.,LTD
 42,SUNGJU-DONGCHANGWON-CITY,
 KYUNGNAM,KOREA,641-716
EuropeanRepresentativeName
EuropeanRepresentativeAddress
EquipmentType/Environment CCTVCamera
ModelName SVD-4600P/WP
BeginningSerialNO. S8080001
YearofManufacture 2008.12.01
Conformanceto EN50081-1:1992
 EMC-Directive89/336EECand92/31/EEC
 EN50130-4:1996
We,the undersigned,hereby declarethattheequipment specified aboveconforms
totheaboveDirective(s).
Manufacturer SAMSUNGTECHWINCO.,LTD LegalRepresentativeinEurope
Signature  Signature
FullName BONJENGGU FullName
Position QUALITYCONTROLMANAGER Position
Place CHANGWON,KOREA Place
Date 2008.12.01 Date
Ø148mm
126mm
83.5mm
46mm
85mm
85mm
85mm
Dimension
SVD-4600(W)N SVD-4600(W)P
POWER
Input voltage AC24V / DC12V
Power consumption 3.5W
CCD
Size Diagonal 6mm (1/3") Sony DS CCD
Total Pixels 811(H) x 508(V) 795(H) x 595(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Sync
Scanning System 2:1 Interlace
Synchronization Internal / Line Lock
Frequency H : 15.734KHz / V : 59.94Hz H : 15.625KHz / V : 50.00Hz
O.S.D
Korean, English, Japanese,
French, Spanish, Portuguese
English, French, Germany, Spanish,
Italy, Chinese, Portuguese
E
L
E
C
T
R
I
C
A
L
Back-light Compensation WDR / HLC / BLC / OFF
Resolution Color : 560 TV Lines↑ B/W : 700TV Lines↑
S/N (Y signal) 52 dB (AGC Off, Weight ON)
Min. Illumination 0.001 Lux (Color Sens-up), 0.00004 Lux (B/W Sens-up) at F1.2
White Balance ATW /AWC / Manual / Outdoor / Indoor (1800°K ~10,500°K)
Electronic Shutter Speed Fixed (1/60 or Flickerless Mode) Fixed (1/50 or Flickerless Mode)
Sens-up AUTO / OFF (Selectable limit x2 ~ x256)
Gain Control LOW/HIGH/OFF
SSNR ON / OFF (1~32 Level)
Motion Detection ON / OFF (8 Zone)
PRIVACY ON / OFF (8 Zone)
V-REV (Mirror) ON / OFF
H-REV (Flip) ON / OFF
FREEZE ON / OFF
SHARPNESS ON / OFF (Level Adjustable)
IRIS Control DC drive Lens
Day & Night COLOR / Black & White / AUTO
DIS ON / OFF
Digital Zoom ON / OFF (x10)
Communication
RS-485 (2400, 4800, 9600, 19200, 38400, 57600 bps selectable)
(STW Protocol, Pelco-D Protocol available)
Built-in Lens x3.6 Vari-focal Lens (F1.2 f2.8~10.0mm)
Angle of view Horizontal
94.4° ~ 28°
Vertical 69.2° ~ 21°
Monitoring angle PAN
Manual 0°~ 340°
TILT Manual 0°~ 146°
Weather Proof IP66
Operating
Temperature/Humidity
-10° to +50° / 30% to 80% RH
Storage Temperature/Humidity 20° to +60° / 20% to 90% RH
Dimension Ø148 x 126 mm
Weight 1.3Kg
※SVD-4600WN, SVD-4600WP : Ivory color base model

P/No. : Z6806-0869-01C
VAN 09. 10
www.samsungtechwin.com
www.samsungcctv.com
•SAMSUNG TECHWIN CO., LTD.
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703
TEL : [phone]~8 FAX : [phone]
•SAMSUNG TECHWIN EUROPE CO., LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : [phone] FAX : [phone]
•SAMSUNG TECHWIN AMERICA Inc.
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : [phone] FAX : [phone]
www.samsungcctvusa.com
SALES NETWORK