Sananbio HAWK Series User manual

Certification
Light Source
Spectrum
PPF
Efficacy
Input Voltage
Input Current
Frequency
Input Power
Fixture Dimensions (L*W*H)
Weight
Temperature Ambient
Mounting Height
Thermal Management
External Control Signal
Dimming Option
Light Distribution
Lifetime
Power Factor
Waterproof Rate
Warranty
Model No.
ETL, CE
Samsung / OSRAM
SP specturm
1720 μmol/s
2.6 μmol/J
120V 208V 220V 240V 277V
5.41A 3.12A 2.95A 2.7A 2.34A
50/60 Hz
650W
117.5cm×110.7cm×7.7cm
10.76 kg
95°F/35℃
≥6" Above Canopy
Passive
0-10V
40% / 50% / 60% / 80/% / 100%/EXT/OFF
120°
L90:>54,000hrs
≥0.97
IP66
5-year warranty
ZK2-ML600-SP02/B
TECHNICAL SPECIFICATIONS:
SANANBIO SP SPECTRUM：
Applicable in all life stages and yield-optimizing
350
100%
80%
60%
40%
20%
0%
463 575
Wavelength (nm)
Relative intensity
688 800
1175mm
1107mm
Powered by
A
G
B
E
H
C
D
F
HAWK Series
SQUAD
GROW LIGNTING

01
3/ENVIRONMENT
This product is intended to be used in green houses and climate-controlled rooms and can be used
in damp environments. However, please DO NOT use this product outdoors or in wet environments
and do not expose it to water. The LED fixture works at optimal capacity when the ambient air em-
perature is between 68~95°F/20~35°C.
Thank you for purchasing the HAWK SQUAD grow light. Our manual will describe the installation
and mounting of the product as well as a description of how to use it. Please have an experienced,
certified service personnel mount and install this device. Please read and understand this manual in
its entirety before using the product. Only use this product as specified within the manual.
The HAWK SQUAD grow light is an electronic horticultural LED fixture with six LED light bars to be
used in green houses or in climate-controlled rooms.In this manual, we will refer to the HAWK
SQUAD grow light as “the LED fixture”.
© Copyright 2021 SANANBIO 2021-04

02
A
G
B
E
H
C
D
F
What’s Included: Solid decking mounts. We suggest hanging the LED fixture from cross bars in a
rack system that has solid support guaranteed not to collapse under weight.
To create proper balance, be sure to position the LED fixture parallel to the length of the rack while
you' re setting up.
・Using the solid decking mounts, loop each mount across the crossbar above the LED Light bar
second from the end of either side of the fixture. Use two decking mounts on either end.
Note: Do not attach mounting hardware to the end light bars. You risk damaging the fixture if you
do.
・Once all four decking mounts are in place, use two people to lift up the LED fixture and mount it
on the decking mounts. You can do this by delicately prying apart the hooks until there is enough
room to slide the fixture between. Release the decking mounts and they will hook around the
fixture.
・Adjust the LED fixture so that each decking mount makes as much surface contact with the fixture
as possible.
© Copyright 2021 SANANBIO 2021-04

03
・Now that the fixture is secured to the decking mounts, you can adjust the position of the lights by
sliding the decking mounts across the cross bars and settle it in the appropriate location for your
growing operation.
Note: It is possible to hang the LED ballast sepa rately.
Please refer to paragraph 6.4
・If you plan to use the LED fixture as a stand alone, continue to paragraph 6.6.
If you plan to use a Master Controller, continue to paragraph 6.5.
If you plan to in stall other LED fixtures, simple repeat the steps from paragraph 6.1 and 6.2.
© Copyright 2021 SANANBIO 2021-04

04
© Copyright 2021 SANANBIO 2021-04

05
© Copyright 2021 SANANBIO 2021-04