Santec Designer Series User manual

KEEP THIS INSTRUC T ION BOOKL E T F O R F U T U R E REFER E N C E
Important : Please register your product online at www.santecfaucet.com
within 30 days of purchase. Santec reserves the right to request additional
documents before servicing warranty requests.
SANTEC has the right to make necessary design changes where applicable.
*Illustration may not depict actual products
1/2" Thermostatic trim with
Volume control /
2-Way diverter /
3-Way diverter

1/2” THERMOSTATIC VALVE AND TRIM
PH9707
PH9708 PH9711
PH9710
Keep this instruction booklet for future reference
0 1
* Please specify the finish when ordering the part.
Part Description Part #
1
2
3
4
5
6
7
8
9
10
11
TH-8000/8200/8300
TH-7000-1
Complete Thermostatic Valve
Mud Guard
Plate
All Thread Extension
Diverter Broach Extension
Diverter Ring
Allen Key
Set Screw
Broach Extension
12
13
14
15
Thermostatic Threaded Sleeve
Teflon Washer
Long Stem Screw
Thermostatic Flange
16 Thermostatic Handle
P00019
P00018
PM-1179
PM-007-1
-VARIES-
SA255
PM-831
PM-5-4X
PM-027
PM-033
-VARIES-
On/Off Handle Assembly
Thermostatic Dial
PH9711, PH9707, PH9708, PH9710
PH9712
TH-7000-3
17 Temperature Restrictor
1 2
3 4 56 7
8
9
17
10 11 12 13 14 15 16
PH9700/9700-1/9701
WILL NEED TO
CUT EXCESS see
pg. 03.D

1/2” THERMOSTATIC EXTENSION KIT
If the valve is roughed too far into the wall, please use the extension kit
provided in the clear plastic bag. To install this kit, first thread part P00055-1
onto part P00019 (FIG.1) and thread the assembly onto the valve. The
remaining parts in the kit can be cut to fit based on the depth the valve is in
the wall. This extension kit can cover up to 0.845”into the wall.
0 2
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 P00055-1 Threaded Sleeve Extension 1
2 SA255-1
Broach for TH-7000 Extension
Kit
1
3
PM-1215 O-Ring for SA255-1 1
4
TH-7000-2
Plastic Temperature
Restrictor for TH-7000
Extension Kit
1
5
PM-1216 O-ring for TH-7000-2 1
6
PM-344 O-ring 1
7 PM-5-4X-1
Screw for TH-7000 Extension
Kit
1
SA255 FOR SA255-1
TH-7000-3 FOR TH-7000-2
PM-5-4X FOR PM-5-4X-1
-REPLACES-
P00055-1
P00019
FIG.1 P00019 Shown threading
onto P00055-1 “which” threads
onto the valve (TH-8000/8200/8300)
12 3 4 5 6 7

-Remove the plastic mud guard #2.
0 3
INSTALLATION INSTRUCTIONS
-Screw the all thread extension
#4 onto the volume control /
diverter valve until it stops.
-Screw on the thermostatic
threaded sleeve #11 and put the
broach extension #10 onto the
thermostatic stem.
- Place #3 Plate up against wall over
valve.
-Slide #6 diverter ring over #4 all
thread extension.
-Thread #7 ON/OFF handle to #4 all
thread extension
-Measure distance between front of
#6 diverter ring and back of #7 ON/
OFF handle
- Remove ON/OFF handle and cut
required amount of thread from #4
required to attach #7 ON/OFF
handle flush to #3 plate.
-Cut #5 diverter broach extension
approximately 1/4" past #4 all thread
extension to allow #7 ON/OFF
handle to attach
-Rough in the valve, orienting the
mud guard #2 flush with the finish
wall ( You can recess up to 1/4”).
-Put the diverter broach extension
#5 onto the volume control /diverter
valve.
-Repeat step D for the broach
extension.
-Replace the newly cut diverter
broach extension and all thread
extension #4 back onto the valve.
-Replace the plate #3 and diverter ring
#6.
-Hand tighten the thermostatic flange
#12 to the threaded sleeve #11.
-Place the On/Off handle assembly #7
onto the diverter broach extension #5
and hand tighten the escutcheon.
Make sure le ver is oriented up
towards the 12’oclock position.
-
u
Insert the thermostatic dial #14 with the “100” mark oriented
pwards to the 12 oclock position over the extension broach #10.
-Secure with the provided long screw #15 and cut excess length to
fit Assemble the thermostatic handle #16 onto the thermostatic
dial and tighten with the the set screw #9 ensuring the handle
faces the 6 o’clock position.

INSTALLATION INSTRUCTIONS
General characteristic
- Santec thermostatic valve is suitable for most water heater systems
provided it is installed correctly
- Low pressure storage heaters are not recommended for this application
Cartridgege CleaningCleaning
After years of use, impurities and lime scale
can restrict the water flow. To clean the
cartridge, please follow these instructions:
1- Remove the handle screw, handle trim,
trim plate screws, and plate.
2- Shut off the water line by turning the
check valve shut off mechanism clockwise.
Make sure that the both hot and cold sides
are closed.
cartridge using a 30mm wrench.3- Remove the
filter under running water or soak it with vinegar or a descaling agent.4- Wash the
the cartridge making sure that the blue lines on the cartridge are aligned.5- Reassemble
check valve shut-off mechanism, turn on the water, and check water flow.6- Open the
flow is normal, reassemble the trims..
7- If the water
IF THE ACTUAL WATER TEMPERATURE IS DIFFERENT FROM THE DIAL :
1- Remove the thermostatic handle with the provided Allen key
2- Turn the water on through the volume control and measure the
actual water temperature with a regular thermometer.
3- Turn the dial until the thermometer shows 100F.
4- Remove the dial handle from the valve.
5- Align the 100F with the center mark
of the valve cylinder, replace screw and tighten.
6- Insert the handle into the cartridge
7- Tighten the handle screw with provided Allen key.
0 4
COLD
WARM
WARMER
HOT COLD
WARM
WARMER
HOT
trim

This warranty does not cover:
This warranty only extends to the original consumer purchaser.
LIFET I ME L IMITE D W ARRANTY
LENGTH O F W A RRANTY & WHO IS C OVERED BY O U R W ARRANTY
WHA T IS C OVERED BY OUR W A RRANTY
EXCLUSIONS ANDL IMITATIONS OF W ARRANTY
1 .
2.
3.
1.
2.
3.
4.
5.
6.
7.
9.
8.
Finishes: SANTEC Polished Chrome, Polished Nickel and Satin Nickel finishes carry a Lifetime Limited
warranty against manufacturing defects and tarnish to the original purchaser. Custom finishes carry a ten
(10) years limited warranty against manufacturi n g defects and tarnish to the original purchaser only.
Kitchen products carry a three (3) year limited warranty.
Cartridges:Santec cartridges carry a lifetime limited warranty, with the exception of thermostatic and
pressure balanced cartridges, which carry a three (3) year limited warranty against manufacturing defects
to the original purchaser.
Parts:Santec parts carry a ten (10) year limited warranty against man ufacturing defects, to the original
purchaser. Kitchen products carry a five (5) year limited warranty.
Drains
Crystals and/or glass
Damage due to negligence, accident, abuse, improper installation, or improper maintenance such as, but not limited to:
heat from soldering during installation, the use of plumber’s putty, damage from tools used during installation, the use
or exposureto chemicals or cleaning products either abrasive or non-abrasive, or the use of any cleaning tool or
product other than a
soft, clean cloth. Reverse osmosis may also shorten the life of the finish.
Changes in the finish or in the product due to normal wear or aging does not cover any products or
parts
which have been altered or used in a manner not typical for the product.
Loss, damages, or expense, incidental or consequential whatsoever, originating from the purchase, installation, use,
repair, failure, or replacement of any
SANTEC pro duct or part, allowed by law.
Commercial and/or Industrial installations and use of the product.
This warranty does not include labor, travel charges, or any costs incurred for repair, removal, installation,
servicing, diagnosing, or handling of either defective or replacement parts. 4
Changes in the finish or in the
product due to normal wear or aging does not cover any products or parts
Access should be provided to the roman tub valves for future service or repair to valves and piping. Under no circumstances will
Santec Faucet, Inc. be liable for any costs associated with the removal of materials for futureaccess to the tub valves or piping for
service or repair.
This warranty does not cover: damage due to negligence, accident, abuse, improper installation, or improper
maintenence such as, (but not limited to): heat from soldering during installation, the use of plumbers putty, damage
from tools used during installation, the use or exposure to chemical or cleaning products, abrasive or non-abrasive, or
the use of any cleaning tool or product other than a soft, clean cloth. This warranty does not cover:
changes in the nish or in the product due to normal wear or again and does not
cover any product or parts which have been altered or used in a manner not typical
for the product. Santec will not be held liable for damage to products caused by the freight carrier, any such
claims should be made immediately with the freight carrier. This warranty does not cover any cost involved in the
installation, repair, or replacement of any SANTEC product or parts. This warranty does not coverand SANTEC will not
be held liable for any loss, damages, or expenses, incidental or consequential whatsoever, originating from the
purchase, installation, use, repair, failure, or replacement of any SANTEC product or part, as allowed by law. The
product of components of the covered product will either be repaired, refinished or replaced at the sole discretion of
SANTEC. SANTEC reserves the right to examine any product claimed defective prior to any warranty claim being
accepted or processed, at its sole discretion. This warranty gives you specific legal rights and you may have other rights
which may vary from state to state.
SANTEC is committed to enhancing your bathroom experience by creating luxury products that will provide
enduring satisftion. Ever y effort has been made to satisfy the highest standards of design and production to create
lasting peace of mind for our customers. Proof of purchase must be provided for all warranty claims, SANTEC provides the
following limited warraties on our product.
Effective: 05/01/2015

Effective: 05/01/2015
CLEAR CO ATED FINISHES
N O N-CLEAR COATED FINISHE S
FINISH CARE INFORMATIO N
TO OB TAIN WARRANTY SERVICE
Please read ‘WHAT IS COVERED BY OUR WARRANTY’and ‘EXCLUSIONS AND LIMITATIONS OF WARRANTY’sections to
understand what is and what is not covered. Please have ready the proof of purchase (original sales receipt), description of
the problem, and carefully package the product or defective part with postage prepaid. Then, please contact your local
SANTECSh owroom or write to SANTEC Technical Services.
WARNING: Do not clean your SANTEC product with ammonia (window cleaner), bleach, soaps, acids, abrasives, harsh polishes,
harsh cleaners, a coarse surfaced cloth, coarse sponge, or any type of scouring pad. Doing so may ruin your faucet finish and/or
void the warranty.
Thank you for making SANTEC a part of your lifestyle and luxury spa experience. Our products have been created as works
of enduring quality and sophisticated design. Luxurious finishes need proper care and attention, so in order to understand
how to properly clean your distinctive luxury finish, please refer to the finish care information below:
Your SANTEC product can be identified in one of two categories: clear coated finishes or non-clear coated finishes. Clear coated finishes
are more scratch-sensitive and are more reactant to harsh cleaning chemicals than non-clear coated finishes. Once you have identified
the specific luxury finish of your SANTEC product, please follow the important corresponding care instructions.
Living nishes are unique, are intended to change over time and are exluded from the
nish warranty. Any product outdoors or in a marine environment are excluded from the
nish warranty.
We recommend that all faucets, drains, etc., be gently wiped dry with a soft cloth after use to avoid water spotting and water
deposit build-up. A mild liquid hand soap may be used occasionally if desired. Use of a non-abrasive carnauba wax
isoccasially required and will add protection to the finish if the faucets will not be dried after use.
Clear Coated Finishes are as Follows:
We recommend that all faucets, drains, etc., be gently wiped dry with a soft cloth after use to avoid water spotting and
water deposit build-up. A mild liquid hand soap may be used occasionally if desired. Use of a non-abrasive carnauba wax
will add protection to the finish and should be used if the faucets will not be dried after use. Santec Orobrass kitchen
products are clear coated. For clear coated finishes, it is recommened to clean your product weekly with a soft moist cloth.
3501 Challenger Street
Torrance, CA 90503
www.santecfaucet.com
Phone. [phone]
Fax. [phone]