Sanus Systems CFA56 User manual

Assembly Instructions for Model: CFA56
Thank you for choosing Sanus Systems Component Furniture. Please check carefully to make sure there are no missing or defective
parts. Never use defective parts. Improper assembly may cause damage or serious injury. If you have any questions regarding this prod-
uct, contact Sanus at 800.359.5520 or visit www.sanus.com. Our customer service representatives can quickly assist you with missing or
damaged parts. Replacement parts for Sanus products purchased through authorized dealers can be shipped directly to you. Please call
Sanus Systems before returning products to the point of purchase.
REQUIRED TOOLS: Phillips Screw Driver, Hammer
Check Carefully to ensure there are no missing Parts or Hardware before beginning the installation.
HARDWARE: (shown at actual size)
(4) Carpet Spike Assembly - a (8) Cam Pin - b (4) Dowel - c (4) Back Panel Bolt - d
(4) Spacer - e (4) Bottom Shelf Pin - f (12) Shelf Pin - g (1) Knob Bolt - h
(1) Knob - i (6) Hinge Screw - j (6) Hinge Plate Screw - k
(4) Isolation Pad - l (4) Isolation Shelf Pin - m (1) Allen Key - n
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 9.29.05
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Parts: *Some Parts not shown at same scale
(4) Foot - o* (3) Hinge Plate - p* (3) Hinge - q*
(2) Front Rail - r (2) Back Rail - s
(2) Side Panel - t* (1) Back Panel - u* (1) Door - v*
(1) Top - w (3) Glass Shelf - x
(1) Isolation Shelf - y (1) Bottom Shelf - z

Step 1: Add feet
Add a Foot (o) to each pillar of each Side Panel Assembly (t) as shown in Diagram 1. If you wish to install the Carpet Spikes (a), thread
each Carpet Spike into the foot as seen in Diagram 1. You can adjust the height of the Carpet Spikes with the Nut shown in the Detailed
View of Diagram 1.
Warning: The ends of the carpet spikes are sharp and may scratch oors or furniture. All sharp objects can be hazardous to
children. For this reason we provide the carpet spikes as an option. Sanus Systems will not be liable for damage or injury.
Diagram 1 Detailed View
t
o
a
Step 2: Attach the Front Rails to the Side Panel Assembly
Attach the Front Rail (r) to the Side Panel Assembly (t) by sliding the clamp down the groove in the Side Panel pillar as shown in the Top
View A of Diagram 2. Make sure the at smooth side of the Front Rail is facing outward, as shown in Diagram 2. Once the Front Rail is
positioned at the bottom of the groove and resting on the Foot (m), tighten the allen bolt on the back side of the Front Rail so the clamp
widens to hold the Front Rail rmly in place. Repeat process for the other Front Rail, making sure it is level with the corner pillar.
Top View A Diagram 2
(Front Left Corner)
t allen bolt
clamp
r

Step 3: Add second Side Panel Assembly
Attach the second Side Panel Assembly (t) by lining up and inserting both Front Rails (r) into the groove in the corner pillar. If the clamp
on the Front Rail will not t in the groove, make sure the allen bolt (labeled in the Top View) is loose so the clamps are close together.
Once you have the Front Rails aligned so the bottom one is resting on the Foot (o), and the top one is level with the corner pillar, tighten
the allen bolt in the back of the Front Rail to widen the clamp to secure it to the pillar. See the Top View of Diagram 3 for assistance.
Top View
(Front Right Corner) Diagram 3
allen bolt t
r clamp
Step 4: Attach the Back Rails
Attach the Cam Pins (b) to the Back Rail (s). Make sure the arrow on each Cam is facing the hole in the outside of the Back Rail and add
two Cam Pins to each end of the Back Rail as shown in the Detailed View of Diagram 4. Insert the Cam Pins until there is a small space
between the head of the pin and the Back Rail.
Attach the Back Rail by sliding the cam pins down the groove on the Side Panel pillar as shown in the Top View of Diagram 4. Once the
Back Rail is resting on the Foot (o), tighten the cams labeled in Diagram 4 to hold it in place. Make sure the bottom Back Rail is oriented
so the threaded holes near the ends are on the top, and the Cams face inside the cabinet, as seen in Diagram 4. Make sure the top Back
Rail is oriented so the threaded holes near the ends are on the bottom, and the Cams face inside the cabinet, as seen in Diagram 4
Diagram 4
Top View
Detailed View (Back Left Corner)
s
cam
b
t b
s

Step 5: Add the Back Panel
Insert a Back Panel Bolt (d) through the Back Panel (u), a Spacer (e) and thread it into the Back Rail (s) as seen in the Detailed View of
Diagram 5. Repeat the process until all 4 Back Panel Bolts are attached to the Back Rails. Proceed to tighten the Back Panel Bolts.
Diagram 5
Detailed View
s
e
d
u
Step 6: Add Isolation Pads to Isolation Shelf
Add an Isolation Pad (l) to each hole in the Isolation Shelf (y) by peeling off the adhesive cover from the soft side of the Isolation Pad
as shown in the Detailed View of Diagram 6. Make sure the soft side of the Isolation Pad is facing toward the shelf when inserting it
into the Isolation Shelf.
Detailed View
Diagram 6
y
l