Sanyo VSP-8000 User manual

FILE NO.
REFERENCE No.SM5310327
L8CSB/US,XE
NOTE: 1. Parts order must contain model number, part number, and description.
2. Substitute parts may be supplied as the service parts.
3. N.S.P. : Not available as service parts.
Design and specifications are subject to change without notice.
(Product Code : 117 523 55)
(U.S.A., Canada)
VSP-8000
SERVICE MANUAL
System controller
CONTENTS
SPECIFICATIONS .................................................................... 3
1. DISASSEMBLY ..................................................................... 4
2. ADJUSTMENT ...................................................................... 6
3. REWRITING THE SOFTWARE ............................................ 7
4. PARTS LIST ....................................................................... 10
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS...........C1
Product safety should be considered when a component replacement is mand in any area of this unit.
Components indicated by the symbol ( ) in the parts list and schematic diagram designate components in which safety can
be of special significance. It is particularly recommended that only parts designated on the parts list in this manual be used for
component replacement designated by the symbol. No deviations from resistance, wattage or voltage ratings may be made for
replacement items designated by the symbol.
PRODUCT SAFETY NOTICE
(Product Code : 117 523 54)
(Europe)
(Taiwan, Korea)
VSP-8000

- 2 -

- 3 -
SPECIFICATIONS
NOTE: The specifications and external appearance of this unit are subject to change without notice.
: RS 485
: RJ-11:2 terminals
Push-lock: 1 pair
: D-SUB (9-pin): 1 port
: Address: 3-bit DIP switch
Termination: 1-bit DIP switch
: 2400, 4800, 9600, 19200 bps
: 15 groups
: Total: 256 devices
Controllers: 5 devices
Multiplexers, timelapse VCRs, cameras, and digital video recorder: 128 devices
each
: 64 devices
: Temparature: 0 to 40 °C
Relative humidity: 80 % or less
: Temparature: -20 to 60 °C
Relative humidity: 80 % or less
: 12 V DC
: 4 W
: 375 (W) x 55 (H) x 165 (D) mm
: 1.5 kg
Communication method
Control terminals
RS-232C terminal
Address/termination switch
Communication speed (baud rate)
Max. no. of groups
Max. no. of connected devices
Dome-type cameras
Ambient conditions
Storage conditions
Power supply
Power consumption
External dimensions
Weight

- 4 -
1
2
3
4
4
Bottom Cover
Shield Case
LCD Assy
Cabinet
CP-1 BOARD
TB-2 BOARD
1. DISASSEMBLY
1-1. REMOVAL OF CABINET AND BOARD LOCATION
Fig. 1

- 5 -
CP-1 BOARD
TB-1 BOARD
TB-2 BOARD
TB-3 BOARD
LCD
OP-1 BOARD
OP-2 BOARD
Fig.2
Fig. 3
2
1
TB-1 BOARD
TB-3 BOARD
OP-1 BOARD
OP-2 BOARD

- 6 -
1. POWER VOLTAGE ADJUSTMENT
1. Adjust VR301 so that voltage of TP302 and TP301 is 5.00 ±
0.10 V.
2. LCD LEVEL ADJUSTMENT
1. Adjust VR302 so that voltage of TP305 and TP301 is 0.575
±0.025 V.
3. JOYSTICK ADJUSTMENT FOR DIRECTION
1. The pin of JK405 is short-circuited and makes the test mode.
2. The FUNCTION button and the number 2 button are pushed
at the same time, and LCD indication is made "TEST
CENTER".
Measuring Point Measuring Equipment Condition
Adj. Value
Digital voltmeter POWER ON
5.00 ±0.10 V
TP302,
TP301 (GND)
VR301
Adj. Location
2. ADJUSTMENT
Measuring Point Measuring Equipment Condition
Adj. Value
Oscilloscope POWER ON
0.575 ±0.025 V
TP305,
TP301 (GND)
VR302
Adj. Location
Fig. 5
TP301
VR302
TP302
TP305
VR301
CP-1 BOARD
3. Push the ENTER button, and set the adjustment mode, and
it confirms that it is indicated with "PLEASE SPIN JST AND
PUSH ENTER" in LCD.
4. It swings, and a circular movement is done about 2-3 laps
JOYSTICK to become a width maximum.
5. It becomes adjustment mode completion if a ENTER button
is pushed and indicated with "TEST MODE" in LCD.
Adjustment is made again if it is indicated with "PLEASE
SPIN JST AND PUSH ENTER" in LCD.
6. The short circuit of the JK405 pin is removed, and the test
mode is finished.
4. JOYSTICK ADJUSTMENT FOR THE ZOOM
1. The pin of JK405 is short-circuited and makes the test mode.
2. The FUNCTION button and the number 3 button are pushed
at the same time, and LCD indication is made "TEST ZOOM
CENTER".
3. Push the ENTER button, and set the adjustment mode, and
it confirms that it is indicated with "PLEASE SLIDE JST AND
PUSH ENTER" in LCD.
4. It swings, and it slides ZOOM lever to become a width
maximum.
5. It becomes adjustment mode completion if a ENTER button
is pushed and indicated with "TEST MODE" in LCD.
Adjustment is made again if it is indicated with "PLEASE
SLIDE JST AND PUSH ENTER" in LCD.
6. The short circuit of the JK405 pin is removed, and the test
mode is finished.
Measuring Point Measuring Equipment Condition
Adj. Value
Adjustment
mode
LCD indication
Joystick
Adj. Location
Measuring Point Measuring Equipment Condition
Adj. ValueAdj. Location
Adjustment
mode
LCD indication
Zoom lever
Fig. 4
RS-232C
CONNECTOR
RESET
RS-232C
CONNECTOR
JK-405
BUTTON

- 7 -
OK Cancel
Connection Description ?X
Name:
Icon:
?X
Change Icon..
Country code:
Area code:
Phone number:
Connect using:
Configure..
OK Cancel
Connect To Settings
Direct to Com1
OK Cancel
COM1 Properties ?X
Bits per second:
Data bits:
Parity:
Stop bits:
Flow control:
Restore Defaults
Advanced...
Hardware
Port Settings
Open
Send Text File ?X
Look in:
File name:
Cancel
Files of type: All files (*.*)
34800
8
None
2
∗∗ Properties
3. REWRITING THE SOFTWARE
3-1. Setting up the computer
Use the Hyper Terminal which is compatible with Windows 95
, 98 or other.
1. Connect the RS-232C connector with the RS-232C con-
nector on the computer using an interlink serial interface
cable. Then turn on the power and start Windows 95 , 98 or
ohter.
2. Open Windows Explorer, and then run the file \Program
Files\Accessories\Hyper Terminal\Hypertrm.exe.
The Connection Description window appears.
3. Click the Cancel button in the Connection Description win-
dow, or enter your name and then click the OK button.
The Hyper Terminal window appears.
4. Click the File (F) button in the Hyper Terminal window, and
then click the Properties (R) button.
The Properties dialog box appears.
5. In the Properties dialog box, set Connect using (N) in Phone
Number to “Direct to COM”, and then click the Configure
(F) button.
The port Setting window of the COM1 Properties dialog box
appears.
6. In the Port Settings window, change the settings to match
the controller.
Speed: 4800, 9600, 19200 or 38400
Data bits: 8
Parity: None
Stop bits: 2
Flow control: Hardware
7. Click the OK button.
The Properties dialog box appears.
8. Click the OK button in the Properties window.
The Hyper Terminal window appears.
9. Click the Transmit (T) button in the Properties dialog box,
and then click the Send Text File (T) button.
The Send Text File dialog box appears.
10. Set File of Type (T) to “All files (*.*)”, and type the name of
the file to be transferred in File name (N).
This completes the computer settings.
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
RS-232C
CONNECTOR
RESET
RS-232C
CONNECTOR
JK-405
BUTTON

- 8 -
SANYO Controller
--:--:--
CLOCK SET
[V 2.00]REWRITE?
OK:ENTER NO:CLR
REWRITE PROGRAM
38400 8 N 2 HARD
REWRITE PROGRAM
3-3. Rewriting data
1. Follow the procedure in 3-1. Setting up the computer.
2. Turn on the power or the system controller, and check that
the initial display appears in the LCD. Then press the MENU
button to set to clock setting mode.
3. Press the 0 button and FUNCTION button simultaneously
to set to software rewriting mode.
The current version number appears in the system control-
ler LCD.
Press the CLEAR button if you want to cancel the opera-
tion.
4. Press the ENTER button to set to baud rate setting mode.
The baud rate setting display appears in the system con-
troller LCD.
Press the CLEAR button if you want to cancel the opera-
tion.
5. Press the [+] and [-] buttons to select the baud rate setting.
6. Press the ENTER button to set to software rewrite standby
mode.
The rewrite standby display appears in the system control-
ler LCD.
3-2. Resetting the computer
If an rewriting error occurs, close the Hyper Terminal, and then
repeat the procedure in 3-1. Setting up the computer from step
2.
Speed: 4800, 9600, 19200 or 38400
Data bits: 8
Parity: None
Stop bits: 2
Flow control: Hardware
←(+)BUTTON (–)BUTTON →
Fig. 10
Initial display mode
Software rewriting mode
Baud rate setting mode
Software rewrite standby mode
Clock setting mode
→ 3 8 4 0 0 ↔1 9 2 0 0 ↔9 6 0 0 ↔4 8 0 0←
RS-232C
CONNECTOR
RESET
RS-232C
CONNECTOR
JK-405
BUTTON

- 9 -
REWRITING...
ADDRESS:0010
REWRITE PROGRAM
ERROR:30
REWRITE PROGRAM
COMPLETE
SANYO Controller
--:--:--
1
RD 2
TD 3
DTR 4
GND 5
DSR 6
RTS 7
CTS 8
9
1
2RD
3 TD
4DTR
5GNG
6DSR
7RTS
8CTS
9
Controller side PC side
7. Click the Open (O) button on the computer screen.
The rewriting display appears in the system controller LCD.
If the software could not be rewritten, an error code appears
in the LCD.
If an error occurs, reset the computer (see “3-2. Resetting
the computer”), and then press the ENTER button and re-
peat the rewriting operation.
Caution:
If an error occurs, do not try to reset the computer by turn-
ing off the system controller power or pressing the RESET
button.
8. When software rewriting is complete, “REWRITE PROGRAM
COMPLETE”appears in the system controller LCD.
Press the ENTER button to the initial display appears in the
LCD.
9. Turn off the power, disconnect the serial cable, and then
install the panel to the rear of the system controller.
Table of error code
3-4. RESET button
The following three items can be cleared using the RESET
button.
1. Clock (time)
2. Password code for security lock (cancels the security lock)
3. Status list
Connection Description
COM1 Properties
Open
Send Text File ?X
Look in:
File name:
Cancel
Files of type: All files (*.*)
∗∗ Properties
Contents
Rewrite mode setting disabled
Access to rewriting prohibition adress
Rewriting operation error
Timeout error when reading
“: ”Data receiving error
ASCII code data error
Record type error
Checksum error
Data count error
Individual data error
Transfer timeout error
Filename error
Error code
13
14
15
16
20
21
22
23
25
26
27
30
Computer screen
Software rewriting mode
Software rewriting error indication
Software rewriting completion
Wiring diagram for RS-232C interlink serial interface cable
Initial display mode

10
4. PARTS LIST
N.S.P.: Not available as service parts.
CABINET AND CHASSIS PARTS
L8CSB/US
12
3
4
44
5
6
6
6
6
6
6
66
6
7
8
9
11
12
16 16
16
16 16 16 16 16 16
16 16
17 17
17
17
18
19
20
21
22
82
23
24 25
26 27
28
29
30
31
32
33
34
35
36 3738 39
40
41
42
43
44
45
46
47
48 49 50 51
52
53
54
55
56
57
58
59
60 6162 63
64
65
66
67
68
69
70
71
72 73
74
75 76 77 78 79 80 81
23
23 23
13 14
15
(N.S.P.)
10
83
83 83

11
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
1 645 053 1385 ASSY,CASE
2 645 039 9091 BADGE (SANYO)
3 645 053 1620 ASSY,TB-2
4 645 053 1248 SCREW M2*6TP
5 645 053 1811 ASSY,LCD
6 645 053 1255 SCREW M3*6
7 645 039 8803 G TERMINAL SCREW M3*10
8 645 053 1392 REAR PANEL
9 645 053 1675 RS232C COVER
10 645 039 8926 HOLDER (Include in the ASSY TB-3)
11 645 053 1637 ASSY,TB-3
12 645 053 1835 KEY SW
13 613 197 9895 ASSY,KNOB,JOY
14 645 053 1668 ZOOM NOB
15 645 053 1408 SHIELD CASE (N.S.P.)
16 645 039 7752 SCREW M3*10TP
17 645 038 5971 CABLE CRAMPER (B)
18 645 053 1613 ASSY,TB-1
19 645 053 1606 ASSY,OP-2
20 645 053 1590 ASSY,OP-1
21 645 053 1842 ASSY,CP-1
22 645 039 8179 COVER,BOTTOM
23 645 039 8797 FOOT (T3, DIA10)
24 645 039 8278 (REW)
25 645 039 8285 (PLAY)
26 645 039 8315 (REVERSE)
27 645 039 8292 (FF)
28 645 039 8322 (STOP)
29 645 053 1422 (TRACKING V.LOCK+)
30 645 039 8384 (REC/PLAY SPEED UP)
31 645 039 8377 (REC/PLAY SPEED DOWN)
32 645 053 1415 (TRACKING V.LOCK-)
33 645 039 8360 (EJECT)
34 645 039 8308 (REC)
35 645 039 8339 (STILL)
36 645 039 8391 (MULTI)
37 645 039 8407 (QUAD)
38 645 053 1507 (CAM MPX)
39 645 039 8414 (PLUS)
40 645 039 8445 (SEQ)
41 645 039 8476 (VCR)
42 645 053 1521 (EXIT BACK)
43 645 039 8490 (NEXT)
44 645 039 8469 (LIVE)
45 645 039 8483 (FULL)
46 645 053 1514 (MON2 SPOT)
47 645 039 8421 (STILL)
48 645 039 8186 (ELS)
49 645 039 8193 (BLC)
50 645 053 1446 (PAN)
51 645 039 8209 (AWC SET)
52 645 039 8230 (AWC RESET)
53 645 053 1453 (TOUR)
54 645 053 1484 (AUX)
55 645 053 1477 (FOUCUS F)
56 645 039 8223 (IRIS+)
57 645 053 1460 (FOUCUS N)
58 645 039 8216 (IRIS-)
59 645 053 1439 (SEQ)
60 645 039 8513 (1)
61 645 039 8520 (2)
62 645 039 8551 (5)
63 645 039 8537 (3)
64 645 039 8568 (6)
65 645 039 8599 (9)
66 645 039 8629 (+)
67 645 039 8605 (0)
68 645 039 8582 (8)
69 645 039 8612 (-)
70 645 039 8575 (7)
71 645 039 8544 (4)
72 645 053 1538 (MENU)
73 645 053 1491 (AF)
74 645 053 1545 (ENTER)
75 645 039 8636 (ALARM LIST)
76 645 053 1361 (STATUS LIST)
77 645 039 8650 (MODE)
78 645 039 8667 (INDIVIDUAL)
79 645 039 8674 (GROUP)
80 645 039 8681 (FUNCTION)
81 645 039 8698 (CLEAR)
82 645 053 1781 SCREW WITH PLATE M3*10TP
83 645 053 1774 NUT(NUT+WASHER+SCREW)
D-SUB CONNECTOR (Included in the ASSY TB-1)

12
Note:
1. Materials of Resistors are abbreviated as follows ;
Resistors
MT-FILM Metallized Film Resistor
MT-GLAZE Metallized Glaze Resistor
OXIDE-MT Oxide Metallized Film Resistor
2. CapacitorsUF :
µ F PF : pF
3. Inductors UH :
µ H MH : mH
4. N.S.P. : Not available as service parts.
ELECTRICAL PARTS
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
ASSY,OP-1
645 053 1590
(DIODES)
D1057 645 039 7998 DIODE ALLEY MA153A
D1058 645 039 7998 DIODE ALLEY MA153A
D1059 645 039 7998 DIODE ALLEY MA153A
D1060 645 039 7998 DIODE ALLEY MA153A
D1061 645 039 7998 DIODE ALLEY MA153A
D1062 645 039 7998 DIODE ALLEY MA153A
D1063 645 039 7998 DIODE ALLEY MA153A
D1064 645 039 7998 DIODE ALLEY MA153A
(CAPACITORS)
C1001 645 039 7547 CERAMIC 0.1UF+80,-20%,50V
C1002 645 039 7547 CERAMIC 0.1UF+80,-20%,50V
C1003 645 053 1200 CERAMIC 0.01UF+80,-20%,50V
C1004 645 053 1200 CERAMIC 0.01UF+80,-20%,50V
(RESISTOR)
R1062 645 039 7554 MT-GLAZE 1/8W 0OHM
(MISCELLANEOUS)
U1001 645 053 1699 STICK CONTROLER (ALPS)
U1002 645 053 1699 STICK CONTROLER (ALPS)
CN101 645 039 8902 16P CABLE ASSY (N.S.P.)
CN102 645 053 1705 8P CABLE ASSY (N.S.P.)
ASSY,OP-2
645 053 1606
(DIODES)
D2008 645 053 1934 DIODE ALLEY MA153A
D2009 645 053 1934 DIODE ALLEY MA153A
D2010 645 053 1934 DIODE ALLEY MA153A
D2011 645 053 1934 DIODE ALLEY MA153A
(BUZZER)
BZ201 645 053 1903 PIEZO BUZZER
(MISCELLANEOUS)
CN201 645 053 1866 9P CABLE ASSY (N.S.P.)
CN202 645 053 1859 6P CABLE ASSY (N.S.P.)
ASSY,CP-1
645 053 1842
(INTEGRATED CIRCUITS)
IC301 645 053 1958 IC,MAX202CSE
IC302 410 428 8708 IC,LC87F5064
IC303 645 053 1972 IC,PST9127SOT-25
IC305 645 053 1965 IC,MAX3082CSA
IC306 645 053 1941 IC,AT24C64-10PC
IC306 645 053 1989 IC SOCKET
IC307 645 053 1927 IC,MN1382-R
IC308 645 053 1873 IC,MAX3100EEE
IC309 645 053 1880 IC,TC74HC86
(SEMICONDUCTORS)
Q3001 645 039 7844 DIGITAL TRANSISTOR DTC114EKA
Q3002 645 039 7844 DIGITAL TRANSISTOR DTC114EKA
Q3003 645 053 1279 DIGITAL TRANSISTOR DTC144EK
Q3004 645 039 7844 DIGITAL TRANSISTOR DTC114EKA
(DIODES)
D3001 645 039 7981 DIODE SB10-05P
D3002 645 039 7974 DIODE SB05-50P
D3003 645 039 7868 DIODE 1SS355
D3004 645 039 7868 DIODE 1SS355
D3005 645 039 7868 DIODE 1SS355
D3006 645 039 7868 DIODE 1SS355
D3007 645 039 7974 DIODE SB05-50P
D3008 645 039 7868 DIODE 1SS355
D3009 645 039 7868 DIODE 1SS355
D3010 645 039 7868 DIODE 1SS355
D3011 645 039 7868 DIODE 1SS355
D3012 645 039 7868 DIODE 1SS355
D3013 645 039 7868 DIODE 1SS355
D3014 645 039 7868 DIODE 1SS355
D3015 645 039 7868 DIODE 1SS355
(INDUCTOR)
L3001 645 053 1293 INDUCTOR 100UH
(DC/DC CONVERTER)
U3001 645 039 8025 DC/DC CONVERTOR BP5220X
(VARIABLE RESISTORS)
VR301 645 039 7820 VR SEMI FIXED 1MOHM
VR302 645 039 7837 VR SEMI FIXED 4.7KOHM
(RESONATORS)
X3001 645 053 1262 RESONATOR CERAMIC,10MHZ
X3002 645 040 2135 RESONATOR CRYSTAL,32.768KHZ
X3003 645 053 1286 RESONATOR CERAMIC,3.68MHZ
(CAPACITORS)
C3001 645 039 7509 CERAMIC,100PF+,-5%,50V
C3002 645 039 7509 CERAMIC,100PF+,-5%,50V
C3003 645 039 7509 CERAMIC,100PF+,-5%,50V
C3004 645 039 7509 CERAMIC,100PF+,-5%,50V
C3005 645 039 7509 CERAMIC,100PF+,-5%,50V
C3006 645 039 7509 CERAMIC,100PF+,-5%,50V
C3007 645 039 7509 CERAMIC,100PF+,-5%,50V
C3008 645 039 7509 CERAMIC,100PF+,-5%,50V
C3009 645 039 7547 CERAMIC,0.1UF+80,-20%,50V
C3010 645 039 7547 CERAMIC,0.1UF+80,-20%,50V
C3011 645 039 7547 CERAMIC,0.1UF+80,-20%,50V
C3012 645 039 7547 CERAMIC,0.1UF+80,-20%,50V
C3013 645 039 7547 CERAMIC,0.1UF+80,-20%,50V
C3014 645 039 7523 CERAMIC,15PF+,-5%,50V
C3015 645 039 7523 CERAMIC,15PF+,-5%,50V
C3016 645 039 7547 CERAMIC,0.1UF+80,-20%,50V
C3017 645 039 7530 CERAMIC,20PF+,-5%,50V
C3021 645 039 7547 CERAMIC,0.1UF+80,-20%,50V
C3022 645 039 7547 CERAMIC,0.1UF+80,-20%,50V
C3023 645 039 7547 CERAMIC,0.1UF+80,-20%,50V
C3024 645 039 7547 CERAMIC,0.1UF+80,-20%,50V
C3025 645 039 7479 ELECTRIC,1000UF,+,-20%,50V
C3026 645 039 7486 ELECTRIC,47UF,+,-20%,50V
C3027 645 039 7486 ELECTRIC,47UF,+,-20%,50V
C3028 645 039 7493 ELECTRIC,470UF,+,-20%,25V
C3029 645 039 7462 ELECTRIC,10UF,+,-20%,16V
C3030 645 039 7462 ELECTRIC,10UF,+,-20%,16V
C3031 645 039 7462 ELECTRIC,10UF,+,-20%,16V
C3032 645 039 7462 ELECTRIC,10UF,+,-20%,16V
C3033 645 039 7486 ELECTRIC,47UF,+,-20%,50V
C3034 645 039 7448 ELECTRIC,1UF,+,-20%,50V
C3035 645 039 7462 ELECTRIC,10UF,+,-20%,16V
C3036 645 039 7486 ELECTRIC,47UF,+,-20%,50V

13
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
CN305 645 039 7912 6P CONNECTOR (N.S.P.)
CN306 645 039 7905 3P CONNECTOR (N.S.P.)
CN307 645 053 1828 2P CONNECTOR (N.S.P.)
ASSY,TB-1
645 053 1613
(SWITCHES)
S4001 645 039 8001 DIP SW
S4002 645 053 1354 TACT SW
S4003 645 053 1309 SLIDE SW
S4004 645 039 8094 S POWER SW
(JACKS/TERMINAL)
JK401 645 039 7721 DC JACK
JK402 645 031 6913 MODULAR JACK
JK403 645 031 6913 MODULAR JACK
JK404 645 039 8070 PUSH LOCK TERMINAL(2P)
JK405 645 039 8100 TEST PIN
(FILTERS)
F4001 645 039 7806 EMI FILTOR
F4002 645 039 7806 EMI FILTOR
F4003 645 039 7806 EMI FILTOR
F4004 645 039 7813 EMI FILTOR
(INDUCTORS)
L4001 645 039 7790 INDUCTOR,0.47UH
L4002 645 039 7790 INDUCTOR,0.47UH
(CAPACITORS)
C4001 645 039 7516 CERAMIC 0.01UF+80,-20%,50V
C4002 645 039 7516 CERAMIC 0.01UF+80,-20%,50V
(DIODES)
D4001 645 053 1347 ZENNER DIODE
D4002 645 053 1347 ZENNER DIODE
D4003 645 053 1347 ZENNER DIODE
D4004 645 053 1347 ZENNER DIODE
(RESISTORS)
R4001 645 039 7608 MT-GLAZE 1/8W 120OHM+,-0.5%
R4002 645 039 7554 MT-GLAZE 1/8W 0OHM
R4003 645 039 7554 MT-GLAZE 1/8W 0OHM
R4004 645 039 7554 MT-GLAZE 1/8W 0OHM
R4005 645 039 7554 MT-GLAZE 1/8W 0OHM
R4006 645 039 7554 MT-GLAZE 1/8W 0OHM
R4008 645 039 7554 MT-GLAZE 1/8W 0OHM
R4009 645 039 7554 MT-GLAZE 1/8W 0OHM
R4010 645 039 7554 MT-GLAZE 1/8W 0OHM
R4011 645 039 7554 MT-GLAZE 1/8W 0OHM
(MISCELLANEOUS)
645 053 1774 NUT(NUT+WASHER+SCREW)
D-SUB CONNECTOR
CN403 645 039 8087 CONNECTOR (9P) D-SUB
CN401 645 039 8872 6P CABLE ASSY (N.S.P.)
CN402 645 039 8896 9P CABLE ASSY (N.S.P.)
ASSY,TB-2
645 053 1620
(LED)
D5001 645 039 7882 LED(GREEN)
D5002 645 039 7875 LED(RED)
(MISCELLANEOUS)
CN501 645 039 8865 3P CABLE ASSY (N.S.P.)
ASSY,TB-3
645 053 1637 ASSY,TB-3
(BATTERY)
Z6001 645 039 8063 BATTERY
(MISCELLANEOUS)
CN601 645 039 7936 CONNECTOR(2P) (N.S.P.)
645 039 8926 HOLDER
C3037 645 039 7462 ELECTRIC,10UF,+,-20%,16V
C3038 645 039 7455 ELECTRIC,100UF,+,-20%,6.3V
C3039 645 039 7547 CERAMIC 0.1UF+80,-20%,50V
C3040 645 039 7516 CERAMIC 0.01UF+80,-20%,50V
C3041 645 039 7516 CERAMIC 0.01UF+80,-20%,50V
C3042 645 039 7516 CERAMIC 0.01UF+80,-20%,50V
C3046 645 039 7547 CERAMIC 0.1UF+80,-20%,50V
C3047 645 053 1194 CERAMIC 0.01UF+,-20%,50V
(RESISTORS)
R3001 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%
R3002 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%
R3003 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%
R3004 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%
R3005 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%
R3006 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%
R3007 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%
R3008 645 039 7646 MT-GLAZE 1/8W 33KOHM+,-0.5%
R3009 645 039 7691 MT-GLAZE 1/8W 560OHM+,-0.5%
R3010 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3011 645 039 7684 MT-GLAZE 1/8W 470KOHM+,-0.5%
R3012 645 039 7592 MT-GLAZE 1/8W 10MOHM+,-0.5%
R3013 645 039 7653 MT-GLAZE 1/8W 330KOHM+,-0.5%
R3014 645 039 7677 MT-GLAZE 1/8W 4.7KOHM+,-0.5%
R3015 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3017 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3018 645 039 7615 MT-GLAZE 1/8W 1.5KOHM+,-0.5%
R3020 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3022 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3025 645 039 7691 MT-GLAZE 1/8W 560OHM+,-0.5%
R3026 645 039 7691 MT-GLAZE 1/8W 560OHM+,-0.5%
R3028 645 039 7615 MT-GLAZE 1/8W 1.5KOHM+,-0.5%
R3029 645 039 7615 MT-GLAZE 1/8W 1.5KOHM+,-0.5%
R3030 645 039 7660 MT-GLAZE 1/8W 390OHM+,-0.5%
R3031 645 039 7707 MT-GLAZE 1/8W 68OHM+,-0.5%
R3032 645 039 7707 MT-GLAZE 1/8W 68OHM+,-0.5%
R3033 645 039 7561 MT-GLAZE 1/8W 100OHM+,-0.5%
R3034 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3035 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3036 645 039 7639 MT-GLAZE 1/8W 270KOHM+,-0.5%
R3037 645 053 1217 MT-GLAZE 1/8W 4.3KOHM+,-0.5%
R3041 645 039 7554 MT-GLAZE 1/8W 0OHM
R3042 645 039 7554 MT-GLAZE 1/8W 0OHM
R3043 645 039 7554 MT-GLAZE 1/8W 0OHM
R3053 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3054 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3055 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3056 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3057 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3058 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3059 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3060 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3064 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3065 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3066 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3067 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3068 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3069 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3070 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3071 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3072 645 039 7554 MT-GLAZE 1/8W 0OHM
R3074 645 039 7554 MT-GLAZE 1/8W 0OHM
R3080 645 039 7554 MT-GLAZE 1/8W 0OHM
R3081 645 039 7554 MT-GLAZE 1/8W 0OHM
R3082 645 039 7554 MT-GLAZE 1/8W 0OHM
R3084 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3085 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
R3086 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3087 645 053 1224 MT-GLAZE 1/8W 470KOHM+,-0.5%
R3089 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3090 645 039 7578 MT-GLAZE 1/8W 1KOHM+,-0.5%
R3091 645 039 7585 MT-GLAZE 1/8W 10KOHM+,-0.5%
(MISCELLANEOUS)
CN301 645 039 7950 16P CONNECTOR (N.S.P.)
CN302 645 039 7950 16P CONNECTOR (N.S.P.)
CN303 645 053 1323 9P CONNECTOR (N.S.P.)
CN304 645 039 7929 9P CONNECTOR (N.S.P.)
CN308 645 053 1316 8P CONNECTOR (N.S.P.)

14
ASSY,LCD
645 053 1811
(LCD)
629 016 4750 LCD DM1623-7BL3
(MISCELLANEOUS)
645 039 8919 16P CABLE ASSY
ACCESSORIES & PACKING MATERIALS
613 196 5065 INSTRUCTION MANUAL(U.S.A. & CANADA)
613 196 5058 INSTRUCTION MANUAL(EUROPE)
645 039 8940 AC ADAPTOR (U.S.A. & CANADA)
645 039 8957 AC ADAPTOR (EUROPE.)
645 053 1712 MODULAR CABLE
645 053 1729 PACKING CASE
645 038 6046 POLY BAG
LOCATION PARTS NO. DESCRIPTION

C1
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
TABLE OF CONTENTS
1. OVERALL WIRING AND CIRCUIT DIAGRAMS
OVERALL WIRING ........................................................................................................................................... C2
TB-1 BOARD ..................................................................................................................................................... C2
CP-1 BOARD .................................................................................................................................................... C3
OP-1 BOARD .................................................................................................................................................... C4
OP-2 BOARD .................................................................................................................................................... C5
TB-2 BOARD ..................................................................................................................................................... C5
TB-3 BOARD ..................................................................................................................................................... C5
2. PRINTED WIRING BOARDS (P.W.B.)
CP-1 P.W.B. ...................................................................................................................................................... C6
TB-1 P.W.B. ...................................................................................................................................................... C6
OP-1 P.W.B. ...................................................................................................................................................... C7
OP-2 P.W.B. ...................................................................................................................................................... C7
TB-2 P.W.B. ...................................................................................................................................................... C7
TB-3 P.W.B. ...................................................................................................................................................... C7
PRODUCT SAFETY NOTICE
THE COMPONENTS DESIGNATED BY A SYMBOL ( ) IN THIS
SCHEMATIC DIAGRAM DESIGNATES COMPONENTS WHOSE
VALUE ARE OF SPECIAL SIGNIFICANCE TO PRODUCT SAFETY.
SHOULD ANY COMPONENT DESIGNATED BY A SYMBOL NEED TO
BE REPLACED, USE ONLY THE PART DESIGNATED IN THE PARTS
LIST.
DO NOT DEVIATE FROM THE RESISTANCE, WATTAGE AND VOLT-
AGE RATINGS SHOWN.

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C2
OVERALL WIRUNG & BLOCK DIAGRAMS
OVERALL WIRING
TB-1 BOARD

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C3
CP-1 BOARD

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C4
OP-1 BOARD

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C5
OP-2 BOARD
TB-3 BOARD
TB-2 BOARD

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C6
PRINTED WIRING POARDS (P.W.B.)
CP-1 P.W.B.
TB-1 P.W.B.
JP3047
C3048
JP3046
C3029
JP3045
C3031
JP3041
CN302
-
-
-
-
IC306
1
JP3048
C3032
JP3044
C3030
JP3042
16
CN308
18
JP3043
X3003
JP3040
JP3038
JP3036
JP3037
JP3039
1
1
13
CN309
JP3034
JP3032
JP3033
JP3031
JP3032
JP3030
JP3029
JP3026
JP3023
JP3019
JP3027
JP3024
JP3018
JP3016
JP3028
JP3025
JP3022
JP3020
JP3017
JP3015
JP3021
CN302
1
16
CN303
1
9
TP304
1
JP3013
C3034
-
X3002
X3001
JP3014
JP3011
-
C3033
TP302
JP3008
JP3006
C3025
-
JP3010
JP3006
JP3005
JP3007
-
-
--
C3037
C3026 C3027
C3025
CN301
16 1
TP302
TP305
C3036
VR302
TP301
VR301
-
JP3004 JP3003
JP3001
-
CN307
31
TP303
C3038
U3001
CN304
JP3012
C3028
-
9
1