Sanyo LNS-T01 Use and care manual

PARTS LIST
Following parts are contained in the packing.
· LENS
· LENS MOUNTING SCREWS
· DRIVER
· LIGHT-BLOCK SHEET
NOTES ON LENS INSTALLATION
LCD PROJECTOR LENS
MODEL NO. LNS-W01
LNS-T01
Lens installation should be performed by the qualified service personnel.
It should be followed by this procedure precisely.
Before attempt to install the lens, confirm the model number (both the LCD
projector and the lens) and use the proper lens.
If you have any questions, contact to the dealers.
Following checks and confirmations should be taken for safety.
Check the following things by the time of the cabinet assembly after the
lens installation.
1. Confirm the lens is securely fixed by 4 screws.
2.Wiring must not be tangled in the mechanical part.
3.There is no missing part, or no loosing mounting part.
1AA6P1P1979-- (ICPW)
1 piece
6 screws (2 for spare)
1 piece
1 sheet
● The focus and zoom of this lens can’t be adjusted by controls on main cabinet or the remote control unit.
LENS REPLACEMENT AND
INSTALLATION PROCEDURE

LENS REPLACEMENT AND INSTALLATION PROCEDURE
Remove screws A (2 screws).
Pull down the lower lens cover while pushing
the part D, then remove it.
Remove screws B (2 screws).
Remove screws C (2 screws) and remove
upper lens cover.
15
Perform the steps to for lens replacement and installation.
1
1.
2.
A
Fig-1
Fig-2
●IN CASE OF MODEL WITHOUT LENS
Remove 2 screws and pull down the plate.
2
3.
4.
UPPER LENS COVER
LOWER LENS COVER
C
B
D
D
COVER PLATE
REMOVE THE LENS COVER. (See figure-1)
(At the step , insert the light-block sheet in
the same position as the removed cover plate
has been placed.Two screws are not used.)
4
REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-2)
LENS
MOTOR LEAD
CONNECTOR “ K16B”
(D)
(D)(D)
(D)
B
A
LENS MOTOR
Fig-3
❋Figure shown inside of the cabinet.
REMOVE THE LENS. (See figure-3.)
1. Remove the connector “K16B” of the
circuit board.
2. Loosen the A, B wire holder and
remove the lens motor lead.
3. Remove screws D (4 screws) which
fastens the lens and remove the lens.
●IN CASE OF MODEL WITH LENS
A
Set the light-block
sheet, so that the
large rounder side
is set over the lens.

MOUNT THE LENS COVER. (See figure-6)
INSTALL THE LENS. (See figure-4)
Remove protective caps(front and
back) on the lens.
Mount the lens on mounting bracket of
the main cabinet with 4 screws.
Use the screws included with the lens.
Use the driver included with the lens
to fasten the screws.
3
1.
2.
A
INSTALL THE LIGHT-BLOCK SHEET. (See figure-5)
When this projector permanently install in the
structure, slide the picture, obtain correct
focus, then lock the lens by Focus Lens Lock
screw at this step.
4
Install the light-block sheet around the lens as shown in the illustration.
Use the sheet included with the lens.
Insert the upper part lens cover and
fix them with screws A (4 screws).
Insert the lower part lens cover and
fix them with screws B. (2 screws).
5
1.
2.
LENS MOUNTING BRACKET
ATTACHED DRIVER
FOCUS LENS LOCK SCREW
UPPER LENS COVER
LOWER LENS COVER
A
B
Fig-4
Fig-5
Fig-6
(After using, save it for latter use.)
When in install the both upper and lower lens
covers, install the light-block sheet so that it
should be placed in the guide slot. (the place
the covers had been placed. See figure-2.). If
the installation of light-block sheet is incor-
rect, it will be the cause of leakage of light or
the dust entering at the main cabinet.
LIGHT-BLOCK SHEET
Adjust focus by rotating
the lens.