Sanyo PLV-HD2000 - 7000 Lumens User manual

EXPAND SERIAL COMMAND
FUNCTIONAL SPECIFICATIONS
PLV-HD2000
SANYO Electric Co., Ltd
Home Electronics Group
AV Company
Projector Business Unit

PLV-HD2000 Expand Serial Command Functional Specifications
2/56
CONTENTS
1．Overview ...................................................................................................................... 4
2．Serial Interface Specification ..................................................................................... 4
2.1. Communication Specification................................................................................. 4
2.2. Connection ............................................................................................................... 4
3．Note for communication............................................................................................. 5
4．Name Definition........................................................................................................... 5
5．Functional Execution Command Table...................................................................... 6
5.1. Image Command Table............................................................................................ 6
5.2. Display Command Table.......................................................................................... 6
5.3. Input Control Command Table................................................................................ 6
5.4. Screen Command Table........................................................................................... 7
5.5. Lamp Command Table............................................................................................. 7
5.6. Setting Command Table .......................................................................................... 7
6．Status Read Command Table..................................................................................... 8
6.1. Image Status Read Command Table....................................................................... 8
6.2. Display Status Read Command Table .................................................................... 8
6.3. Video Status Read Command Table ....................................................................... 8
6.4. Input Status Read Command Table ........................................................................ 9
6.5. Screen Status Read Command Table..................................................................... 9
6.6. Lamp Status Read Command Table........................................................................ 9
6.7. Setting Status Read Command Table................................................................... 10
6.8. Other Status Read Command Table...................................................................... 10
7．Error Code Table........................................................................................................ 10
8．Functional Execution Command.............................................................................. 11
8.1. Format..................................................................................................................... 11
8.2. Transfer Example ................................................................................................... 11
8.3. Operation Requirements ....................................................................................... 11
8.4. Image Command .................................................................................................... 12
8.5. Display Control Command.................................................................................... 17
8.6. Input Control Command........................................................................................ 22
8.7. Screen Control Command..................................................................................... 25
8.8. Lamp Command..................................................................................................... 27
8.9. Setting Command .................................................................................................. 28
9．Status Read Command ............................................................................................. 32
9.1. Format..................................................................................................................... 32
9.2. Transfer Example ................................................................................................... 32
9.3. Image Status Read Command............................................................................... 33
9.4. Display Status Read Command ............................................................................ 36

PLV-HD2000 Expand Serial Command Functional Specifications
3/56
9.5. Status Read Command for Video.......................................................................... 38
9.6. Input Status Read Command ................................................................................ 39
9.7. Screen Status Read Command............................................................................. 45
9.8. Lamp Status Read Command................................................................................ 46
9.9. Setting Status Read Command............................................................................. 48
9.10. Other Status Read Command.............................................................................. 51
10．Command with Address Specification .................................................................. 54
10.1. Overview ............................................................................................................... 54
10.2. Functional Execution Command with address.................................................. 55
10.3. Status Read Command with Address................................................................. 56

PLV-HD2000 Expand Serial Command Functional Specifications
4/56
1．Overview
・ This Functional Specification defines communication functions to Network card for PLV-HD2000.
・ The Commands are designed to communicate with Network board, but most commands can be
used to remote-control a projector through RS-232C from a computer. Therefore these commands
are defined as Expand Serial Commands.
・ When using commands with address, refer to [10.Command with Address Specification].
2．Serial Interface Specification
2.1. Communication Specification
Items Specification
Synchronoun System Asynchronous
Transmission Speed 9600 / 19200
Data Length 8 bits
Parity N/A
Stop Bit 1
Flow Control N/A
Note1) Transmission speed: initial setting value is 19200
Note2) Transmission speed can be changed in Service Mode
2.2. Connection
Dedicated serial cables that come with the projector must be used for the connection between a
computer and the projector.
PC Projector
COM 1 Serial Port IN
（D-Sub 9Pin）（D-Sub 9Pin）
Connect COM port of a computer to SERIAL PORT IN of a projector.
COM Port (COM1 or COM2) of a computer is specified by the control software of the computer.

PLV-HD2000 Expand Serial Command Functional Specifications
5/56
3．Note for communication
・ Expand Serial Command is defined as a single command per line that starts with “C” and ends with
carriage return (0x0D).
・ When a projector receives carriage return (0x0D), it starts decoding.
・ There are two types of commands as below:
-Example of Functional Execution Command: ”CF_BRIGHT_032” [CR]
-Example of Status Read Command: “CR_BRIGHT” [CR]
Note) “_” indicates a space
・ Projector clears the information of buffer in the following cases:
-When the projector receives LF(0x0A) or EOF(0x1A).
-When it takes more than one second to receive a single command
(Until receiving the carriage return after the reception of the first data)
・ When executing several commands in a row, allow 100 ms from the reception of the response to the
previous command.
More than 100 ms
Command
PC →Projector “CF_BRIGHT_032” CR Next Command
Projector →PC “000” CR
Response
(A few ms ~ 5s)
* When the command is sent without waiting for the response to the previous command, the
projector may not operate properly.
* Howerver this is not the case when there is no response for more than 5 seconds.
・ Projector takes about 5 seconds for internal initialization after plugging in AC power. During this time
projector cannot process commands. Do not issue any command.
・ Serial Commands are invalid when Service Mode or Special menu is displayed.
4．Name Definition
・ Data from a controller to a projector is represented as COMMAND, and data from a projector to a
controller for the incoming command is represented as RESPONSE.
・ [CR]: Carriage Return Code
The command ends with carriage return code.
Response also ends with carriage return code.
・ _: Space Code
All space code is expressed by (_).
・ %1: Parameter included in Command
When there is more than one parameter, they are defined as %2, %3…
・ %%%: Error Code from a projector
Acceptable: “000”
Unacceptable: Refer to [7.Error Code Table“ for the error number

PLV-HD2000 Expand Serial Command Functional Specifications
6/56
5．Functional Execution Command Table
5.1. Image Command Table
Execute command Item
CF_BRIGHT_%1 [CR] Set value of Brightness
CF_CONT_%1 [CR] Set value of Contrast
CF_COLOR_%1 [CR] Set value of Color
CF_TINT_%1 [CR] Set value of Tint
CF_SHARP_%1 [CR] Set value of Sharpness
CF_GAMMA_%1 [CR] Set value of Gamma
CF_WBAL-R_%1 [CR] Set Red value of White Balance
CF_WBAL-G_%1 [CR] Set Green value of White Balance
CF_WBAL-B_%1 [CR] Set Blue value of White Balance
CF_COLTEMP_%1 [CR] Set value of Color Temp.
CF_NZRED_%1 [CR] Set / Cancel Noise reduction
CF_PROGV_%1 [CR] Set / Cancel Progressive
CF_IMAGE_%1 [CR] Set Image mode
CF_IMAGEADJ_%1 [CR] Reset / Store adjusted values of Image
CF_APCTRL_%1 [CR] Set level of Auto Picture Control
CF_BBAL_%1_%2_%3 [CR] Set value of Gamma Balance
5.2. Display Command Table
Execute command Item
CF_FSYNC_%1 [CR] Set value of Fine Sync
CF_TODOTS_%1 [CR] Set value of Total Dots
CF_CLAMP_%1 [CR] Set value of Clamp
CF_H-POS_%1 [CR] Set value of Horizontal Position
CF_V-POS_%1 [CR] Set value of Vertical Position
CF_DLINE_%1 [CR] Set value of Display Line
CF_DDOTS_%1 [CR] Set value of Display Dots
CF_SETDISPADJ_%1 [CR] Apply values set in PC Adj menu to screen image
CF_ORGMODE_%1 [CR] Specify the original signal of the Display mode
CF_MODESTORE_%1 [CR] Store values set in Display adjust menu to Mode ％1
CF_MODEFREE_%1 [CR] Clear values stored in Mode %1 and return it to Free
status
5.3. Input Control Command Table
Execute command Item
CF_INPUT_%1 [CR] Select Input %1
CF_SOURCE_%1 [CR] Select Input Source %1
CF_INPUT1_%1 [CR] Select Input 1 and Source %1
CF_INPUT2_%1 [CR] Select Input 2 and Source %1
CF_INPUT3_%1 [CR] Select Input 3 and Source %1
CF_INPUT4_%1 [CR] Select Input 4 and Source %1
CF_SYSTEM_%1 [CR] Select System %1

PLV-HD2000 Expand Serial Command Functional Specifications
7/56
5.4. Screen Command Table
Execute command Item
CF_SCREEN_%1 [CR] Select Screen size
CF_VSCALE_%1 [CR] Set value of V Scale
CF_VPOS_%1 [CR] Set value of V Position
CF_HSCALE_%1 [CR] Set value of H Scale
CF_HPOS_%1 [CR] Set value of H Position
5.5. Lamp Command Table
Execute command Item
CF_LAMPH_%1 [CR] Reset total running time of each lamp
CF_LAMPMODE_%1 [CR] Select lamp mode (Full/Half)
CF_AUTOLAMPCONTRL_%1 [CR] Switch ON/OFF of auto lamp control
5.6. Setting Command Table
Execute command Item
CF_BBACK_1 [CR] Set / Cancel Blue Back function
CF_DISP_%1 [CR] Set / Cancel Display function
CF_LOGO_%1 [CR] Set / Cancel Logo function
CF_CEIL_%1 [CR] Set / Cancel Ceiling function
CF_REAR_%1 [CR] Set / Cancel Rear function
CF_RCODE_%1 [CR] Select Remote Control Code
CF_LANG_%1 [CR] Select language for OSD
CF_ON-STA_%1 [CR] Set Power ON Start function
CF_P-MANE_%1 [CR] Set mode of Power Management
CF_P-MANETIME_%1 [CR] Set value of Power Management timer
CF_FANSPEED_%1 [CR] Select level of Fan Speed
CF_KEYDIS_%1 [CR] Set limitation of RC / KEY use
CF_FDEFAULT_%1 [CR] Set values to Factory Default setting

PLV-HD2000 Expand Serial Command Functional Specifications
8/56
6．Status Read Command Table
6.1. Image Status Read Command Table
Status read command Item
CR_BRIGHT [CR] Get value of Brightness
CR_CONT [CR] Get value of Contrast
CR_COLOR [CR] Get value of Color
CR_TINT [CR] Get value of Tint
CR_SHARP [CR] Get value of Sharpness
CR_GAMMA [CR] Get value of Gamma
CR_WBAL-R [CR] Get Red value of White Balance
CR_WBAL-G [CR] Get Green value of White Balance
CR_WBAL-B [CR] Get Blue value of White Balance
CR_COLTEMP [CR] Get setting status of Color temperature
CR_NZRED [CR] Get setting status of Noise reduction
CR_PROGV [CR] Get setting status of Progressive
CR_IMAGE [CR] Get selected Image mode
CR_IMGGMD [CR] Get selected Image Gamma mode
CR_APCTRL [CR] Get setting status of Auto Picture Control
CR_BBAL [CR] Get setting status of Gamma Balance
6.2. Display Status Read Command Table
Status read command Item
CR_FSYNC [CR] Get value of Fine Sync
CR_TDOTS [CR] Get value of Total Dots
CR_CLAMP [CR] Get value of Clamp
CR_H-POS [CR] Get value of Horizontal Position
CR_V-POS [CR] Get value of Vertical Position
CR_DLINE [CR] Get value of Display Line
CR_DDOTS [CR] Get value of Display Dots
CR_ORGMODE [CR] Get the original signal of the Display mode
CR_MODESTORE [CR] Get Free or Stored status for Display Adj. Mode 1-20
CR_SETDISPADJ[CR] Get signal types currently displayed in System menu.
6.3. Video Status Read Command Table
Status read command Item
CR_SERSYS [CR] Get currently selected signal. When in Auto mode, it
returns a result by Auto detect

PLV-HD2000 Expand Serial Command Functional Specifications
9/56
6.4. Input Status Read Command Table
Status read command Item
CR_INPUT [CR] Get selected Input No
CR_SOURCE [CR] Get selected Input Source
CR_SRCINP1 [CR] Get selected source for Input 1
CR_SRCINP2 [CR] Get selected source for Input 2
CR_SRCINP3 [CR] Get selected source for Input 3
CR_SRCINP4 [CR] Get selected source for Input 4
CR_SYSTEM [CR] Get selected System in the Input mode
CR_SYSLIST [CR] Get possible system list
CR_MODELIST [CR] Get possible mode list
CR_HMSLOT [CR] Get the total number of inputs
CR_NMSLOT1 [CR] Get Slot board name inserted to Input 1
CR_NMSLOT2 [CR] Get Slot board name inserted to Input 2
CR_NMSLOT3 [CR] Get Slot board name inserted to Input 3
CR_NMSLOT4 [CR] Get Slot board name inserted to Input 4
CR_IDSLOT1 [CR] Get Slot board ID inserted to Input 1
CR_IDSLOT2 [CR] Get Slot board ID inserted to Input 2
CR_IDSLOT3 [CR] Get Slot board ID inserted to Input 3
CR_IDSLOT4 [CR] Get Slot board ID inserted to Input 4
6.5. Screen Status Read Command Table
Status read command Item
CR_SCREEN [CR] Get selected screen size
CR_VSCALE [CR] Get value of V Scale
CR_VPOS [CR] Get value of V Position
CR_HSCALE [CR] Get value of H Scale
CR_HPOS [CR] Get value of H Position
6.6. Lamp Status Read Command Table
Status read command Item
CR_LAMPREPL [CR] Get the information on Lamp replacement time
CR_LAMPMODE [CR] Get selected Lamp mode
CR_AUTOLAMPCONTRL [CR] Get selected Lamp Control mode
CR_LAMPSTS [CR] Get the information on Lamp lighting status
CR_INFLAMP [CR] Get Lamp switching status
CR_PROJH [CR] Get total running time of the projector
CR_HMLAMP [CR] Get the total number of lamps

PLV-HD2000 Expand Serial Command Functional Specifications
10/56
6.7. Setting Status Read Command Table
Status read command Item
CR_BBACK [CR] Get setting status of Blue Back
CR_DISP [CR] Get setting status of Display
CR_LOGO [CR] Get setting status of Logo
CR_RCODE [CR] Get selected Remote Control Code
CR_LANG [CR] Get selected language
CR_ON-STA [CR] Get setting status of ON Start
CR_P-MANE [CR] Get setting status of Power Management
CR_P-MANETIME [CR] Get setting time for Power Management
CR_FANSPEED [CR] Get selected Fan Control Speed level
CR_KEYDIS [CR] Get limitation status of RC/KEY use
6.8. Other Status Read Command Table
Status read command Item
CR_PRESSURE [CR] Get Air Pressure data
CR_SIGNAL [CR] Get Signal status if there is signal or not
CR_VMUTE [CR] Get setting status of No Show
CR_FREEZE [CR] Get setting status of Freeze
CR_INFPFAIL [CR] Get the information on Power Failure
CR_TEMPWARN [CR] Get temperature status whether it is close to abnormmal level
or not
CR_TEMPFAIL [CR] Get temperature in abnormal temperature status
7．Error Code Table
Error Code Contents
? -When the received data cannot be decoded
-Parameter determination error (digit number error,
including invalid value)
000 Normal reception (Not error)
101 The function is invalid in the selected mode
102 The selected value is out of range (The value is not
be applied)
103 The command is not available to the hardware (the
command is for the optional function which is not
supported by the given hardware)

PLV-HD2000 Expand Serial Command Functional Specifications
11/56
8．Functional Execution Command
8.1. Format
1. PC issues a command in the format below:
Pattern1: “CF _ Command” [CR]
Pattern2: “CF _ Command _” %1 [CR]
CF_: Header
Command: String
%1: Parameter (string)
_: Space (To separate Command and Parameter)
2. The projector decodes the received data and when it gets ready to receive the next
command, it returns the response.
“000” [CR]: (0x06 ,0x0D) When receiving Function Execution Command
“nnn” [CR]: Except “000”, when it cannot execute commands for some specific reason
For details, refer to [7. Error Code Table
3. When the received data cannot be decoded, the projector returns
“ ? “ [CR]
8.2. Transfer Example
When setting total dots for the projector to 1344 by Expand Serial Command
PC →PJ: “CF_TODOTS_1344” [CR]
PC ←PJ: “000” [CR] ---------------- Acceptable
8.3. Operation Requirements
Functional Execution Command is limited when the projector is in the following status.
However, Status Read Command is effective under these conditions.
Projector Status Valid Function Execution Command
In Standby mode C00: POWER ON
Count Down in process C00: POWER ON
(Count Down is terminated)
Cooling Down in process N/A
Cooling Down due to abnormal temperature N/A
Abnormal Temperature N/A
Power Failure
(60 seconds after Power failed) N/A
Power Management / Cooling Down in
process N/A
Power Management in process C00: POWER ON
C01: POWER OFF
Note) When the projector receives the other command in the above status, it returns error code
of showing the status.

PLV-HD2000 Expand Serial Command Functional Specifications
12/56
8.4. Image Command
8.4.1. CF_ BRIGHT Command
Command “CF_BRIGHT_%1” [CR]
%1
“000-063” --------- Directly specify setting value of Brightness
“UP” ---------------- Increment setting value of Brightness by 1
“DN” ---------------- Decrement setting value of Brightness by 1
Details
Set Brightness value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting. (It is stored in Standby mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.2. CF_CONT Command
Command “CF_CONT_%1” [CR]
%1
“000-063” --------- Directly specify setting value of Contrast.
“UP” ---------------- Increment setting value of Contrast by 1.
“DN” ---------------- Decrement setting value of Contrast by 1.
Details
Set Contrast value (valid only when it is in the normal Power ON status)
The value set by this command is not stored to the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting. (It is stored in Standby mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.3. CF_COLOR Command
Command “CF_COLOR_%1” [CR]
%1
“000-063” --------- Directly specify setting value of Color.
“UP” ---------------- Increment setting value of Color by 1.
“DN” ---------------- Decrement setting value of Color by 1.
Details
Set Color value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting. (It is stored in Standby mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.4. CF_TINT Command
Command “CF_TINT_%1” [CR]
%1
“000-063” --------- Directly specify setting value of Tint.
“UP” ---------------- Increment setting value of Tint by 1.
“DN” ---------------- Decrement setting value of Tint by 1.
Details
Set Tint value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting. (It stays in Standby mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]

PLV-HD2000 Expand Serial Command Functional Specifications
13/56
8.4.5. CF_SHARP Command
Command “CF_SHARP_%1” [CR]
%1
“000-015” --------- Directly specify setting value of Sharpness.
“UP” ---------------- Increment setting value of Sharpness by 1.
“DN” ---------------- Decrement setting value of Sharpness by 1.
Details
Set Sharpness value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting. (It is stored in Standby mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.6. CF_GAMMA Command
Command “CF_GAMMA_%1” [CR]
%1
“000-015” ---------- Directly specify setting value of Gamma.
“UP” ----------------- Increment setting value of Gamma by 1.
“DN” ----------------- Decrement setting value of Gamma by 1.
Details
Set Gamma value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting. (It is stored in Standby mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.7. CF_WBAL- Command
Command “CF_WBAL-%1_%2” [CR]
%1
“R” ------------- RED
“G” ------------- GREEN
“B” ------------- BLUE
%2
“000-063” ----- Directly specify value of color set in %1.
“UP” ------------ Increment value of color set in %1 by 1.
“DN” ------------ Decrement color value set in %1 by1.
Details
Set value of color specified by White Balance %1
(valid only when it is in the normal Power ON status)
The value set by this command is not stored in the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting. (It is stored in Standby mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]

PLV-HD2000 Expand Serial Command Functional Specifications
14/56
8.4.8. CF_COLTEMP Command
Command “CF_COLTEMP_%1” [CR]
%1
“000” ---------------- XLow
“001” ---------------- Low
“002” ---------------- Mid
“003” ---------------- High
Details
Set level of Color Temp. (valid only when it is in the normal Power ON status)
The value set by this command is not stored in the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting. (It is stored in Standby mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.9. CF_NZRED Command
Command “CF_NZRED_%1” [CR]
%1
“OFF” ---------------------- Set Noise Reduction to OFF.
“L1” ------------------------- Set Noise Reduction level to L1.
“L2” ------------------------- Set Noise Reduction level to L2.
“L3” ------------------------- Set Noise Reduction level to L3.
Details
Set/Cancel Noise Reduction (valid only when it is in the normal Power ON status)
The value set by this command is not stored in the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting. (It is stored in Standby mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.10. CF_PROGV Command
Command “CF_PROGV_%1” [CR]
%1 “ON” ----------- Set Progressive to ON.
“OFF” --------- Set Progressive to OFF.
Details
Set/Cancel Progressive (valid only when it is in the normal Power ON status)
The value set by this command is not stored in the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting. (It is stored in Standby mode.)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]

PLV-HD2000 Expand Serial Command Functional Specifications
15/56
8.4.11. CF_IMAGE Command
Command “CF_IMAGE_%1” [CR]
%1
“STANDPC” ------- Standard (PC)
(Image Adj. value is fixed to factory default for Still Image)
“STANDAV” -------- Standard (AV)
(Image Adj. value is fixed to factory default for Moving Image)
“REAL” ------------ Real (Fixed value to display a graphic image with natural tone)
“CINEMA” ----- Cinema (Fixed value to focus on the tone reproduction for movie)
“CUSTOM1” ------------- Image1 (the value set and store by a user)
“CUSTOM2” ------------- Image2 (the value set and store by a user)
“CUSTOM3” ------------- Image3 (the value set and store by a user)
“CUSTOM4” ------------- Image4 (the value set and store by a user)
“CUSTOM5” ------------- Image5 (the value set and store by a user)
“CUSTOM6” ------------- Image6 (the value set and store by a user)
“CUSTOM7” ------------- Image7 (the value set and store by a user)
“CUSTOM8” ------------- Image8 (the value set and store by a user)
”CUSTOM9” ------------- Image9 (the value set and store by a user)
“CUSTOM10” ----------- Image10 (the value set and store by a user)
Details
Select Image Mode (valid only when it is in the normal Power ON status)
Parameter “CUSTOM1” to “CUSTOM10” corresponds to “Image1” to “Image10”
displayed in the projector OSD menu on selecting Image.
The value set by this command is stored in EEPROM so that the setting can
remain effective evern after the power is turned to ALL OFF status.
Acceptable “000”[CR]
Response
Unacceptable “Error Code”[CR]
8.4.12. CF_IMAGEADJ Command
Command “CF_IMAGEADJ_%1” [CR]
%1
“RST” ------ Reset adjusted value for the Image.
“STR1” ---- Store current adjusted value to Image1
“STR2” ---- Store current adjusted value to Image2
“STR3” ---- Store current adjusted value to Image3
“STR4” ---- Store current adjusted value to Image4
“STR5” ---- Store current adjusted value to Image5
“STR6” ---- Store current adjusted value to Image6
“STR7” ---- Store current adjusted value to Image7
“STR8” ---- Store current adjusted value to Image8
“STR9” ---- Store current adjusted value to Image9
“STR10” ---- Store current adjusted value to Image10
Details
Reset/Store adjusted value of Image.
(Only valid when it is in the normal Power ON status)
“STR1” – “STR10” corresponds to “Image1” – “Image10” displayed in projector
OSD menu on selecting “Store” for adjusted value of Image. The settig value set
in “Image1” to “Image10” is stored and can be retrieved when turning on the
projector again after the power is turned to ALL OFF status.
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]

PLV-HD2000 Expand Serial Command Functional Specifications
16/56
8.4.13. CF_APCTRL Command
Command “CF_APCTRL_%1” [CR]
%1
“L1” ------------------- Set Auto Picture Control to Level 1.
“L2” ------------------- Set Auto Picture Control to Level 2.
“OFF” ---------------- Set Auto Picture Control to OFF.
Details Set the level of Auto Picture Control (valid only when it is in the normal Power ON
status)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.4.14. CF_BBAL Command
Command “CF_BBAL-%1_%2_%3” [CR]
%1
“R” ----------- Red
“G” ----------- Green
“B” ----------- Blue
%2 “0”-“2” ------------ Point “0” = 140, Point ”1” = 300, Point “2” = 600
%3 “-32” – “032” ------ Offset value of Gamma adjustment at the point specified in %2.
“000” is the center value.
Details
Set Offset value ot Gamma adjustment at the specifiyed point. (valid only when it
is in the normal Power ON status)
Therefore, when the power is turned to ALL OFF status, the value returns to the
original setting.
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]

PLV-HD2000 Expand Serial Command Functional Specifications
17/56
8.5. Display Control Command
8.5.1. CF_FSYNC Command
Command “CF_FSYNC_%1” [CR]
%1
“0000-0031” -------- Directly spcify setting value of Fine Sync
“UP” ------------------ Increment setting value of Fine Sync by 1
“DN” ------------------ Decrement setting value of Fine Sync by 1
Details
Set Fine Sync value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in projector’s memory. Therefore,
when the power is turned to ALL OFF status, the value returns to the original
setting. (It is stored in Standby mode.)
Note: When %1 is directly specified, CF_SETDISPADJ as well as this command is
requied In order to apply the setting value to the display image.
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.5.2. CF_TDOTS Command
Command “CF_TDOTS_%1” [CR]
%1
“nnnn - 9999” ------ Directly specify setting value of Total Dots
“nnnn” indicates minimum value, which is current (Display Dots + Position H) value
“UP” ---------------- Increment setting value of Total Dots by 1
“DN” ---------------- Decrement setting value of Total Dots by 1
Details
Set Total Dots value (Only valid when it is in the normal Power ON status)
The value set by this command is not stored in projector’s memory. Therefore,
when the power is turned to ALL OFF status, the value returns to the original
setting. (It is stored in Standby mode.)
Note: When %1 is directly specified, CF_SETDISPADJ as well as this command is
requied In order to apply the setting value to the display image.
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.5.3. CF_CLAMP Command
Command “CF_CLAMP_%1” [CR]
Input is
PC
“0000 - 0127” ------- Directly specify setting value of Clamp
“UP” ------------------- Increment setting value of Clamp by 1
“DN” ------------------- Decrement setting value of Clamp by 1
%1
Input is
Video
“0000 - 1023” ------- Directly specify setting value of Clamp
“UP” ------------------- Increment setting value of Clamp by 1
“DN” ------------------- Decrement setting value of Clamp by 1
Details
Set Clamp value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in projector’s memory. Therefore,
when the power is turned to ALL OFF status, the value returns to the original
setting. (It is stored in Standby mode.)
Note: When %1 is directly specified, CF_SETDISPADJ as well as this command is
requied In order to apply the setting value to the display image.
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]

PLV-HD2000 Expand Serial Command Functional Specifications
18/56
8.5.4. CF_H-POS Command
Command “CF_H-POS_%1” [CR]
Input is
PC
“0000 - nnnn” ---- Directly specify setting value of Horizontal Position
“nnnn” indicates maximum value, which is current value of
(Total Dots - Display Dots).
“UP” ---------------- Increment setting value of Horizontal Position by 1
“DN” ---------------- Decrement setting value of Horizontal Position by 1
%1
Input is
Video
“0000 - 4095” ---- Directly specify settign value of Horizontal Position
“UP”---------------- Increment setting value of Horizontal Position by 1
“DN”---------------- Decrement setting value of Horizontal Position by 1
Details
Set Horizontal Position value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in projector’s memory. Therefore,
when the power is turned to ALL OFF status, the value returns to the original
setting. (It is stored in Standby mode.)
Note: When %1 is directly specified, CF_SETDISPADJ as well as this command is
requied In order to apply the setting value to the display image.
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.5.5. CF_V-POS Command
Command “CF_V-POS_%1” [CR]
Input is PC
“0000 - nnnn” --- Directly specify settting value of Vertical Position
“nnnn” indicates maximum value, which is current value of (Total
Line – Display Line).
“UP” --------------- Increment setting value of Vertical Position by 1
“DN” --------------- Decrement setting value of Vertical Position by 1
%1
Input is
Video
“-mmm - nnnn” --- Directly specify setting value of Vertical Position
“UP” --------------- Increment setting value of Vertical Position by 1
“DN” --------------- Decrement setting value of Vertical Position by 1
Details
Set Vertical Position value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in projector’s memory. Therefore,
when the power is turned to ALL OFF status, the value returns to the original
setting. (It is stored in Standby mode.)
Note: When %1 is directly specified, CF_SETDISPADJ as well as this command is
requied In order to apply the setting value to the display image.
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]

PLV-HD2000 Expand Serial Command Functional Specifications
19/56
8.5.6. CF_DLINE Command
Command “CF_DLINE_%1” [CR]
Input is
PC
“0100 - nnnn” --- Directly specify setting value of Display Line
“nnnn” indicates maximum value, which is current value of
(Total Line – Vertical Position).
“UP” --------------- Increment setting value of Display Line by 1
“DN” --------------- Decrement setting value of Dsplay Line by 1
%1
Input is
Video
“0100 - nnnn” --- Directly specify setting value of Display Line
“nnnn” indicates maximum value, which is the initial value
when signal is changed.
“UP” --------------- Increment setting value of Display Line by 1
“DN” --------------- Decrement setting value of Display Line by 1
Details
Set Display Line value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in projector’s memory. Therefore,
when the power is turned to ALL OFF status, the value returns to the original
setting. (It is stored in Standby mode.)
Note: When %1 is directly specified, CF_SETDISPADJ as well as this command is
requied In order to apply the setting value to the display image.
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.5.7. CF_DDOTS Command
Command “CF_DDOTS_%1” [CR]
Input is
PC
“0100 - nnnn” --- Directly specify setting value of Display Dots
“nnnn” indicates maximum value.
This value equals to the current value of Total Dots - Horizontal Position -1
“UP” ---------------- Increment setting value of Display Dots by 1
“DN” ---------------- Decrement settinfg value of Display Dots by 1
%1
Input is
Video
“0100 - nnnn” --- Directly specify setting value of Display Dots
Value shold be “even” number. When “odd” number is selected, it is
rounded down to the nearest even number like “0123”→”0122”.
“nnnn” indicates maximum value, which is the initial value when signal
is changed.
“UP” ---------------- Increment setting value of Display Dots by 2
“DN” ---------------- Decrement setting value of Display Dots by 2
Details
Set Display Dots value (valid only when it is in the normal Power ON status)
The value set by this command is not stored in projector’s memory. Therefore,
when the power is turned to ALL OFF status, the value returns to the original
setting. (It is stored in Standby mode.)
Note: When %1 is directly specified, CF_SETDISPADJ as well as this command is
requied In order to apply the setting value to the display image.
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]

PLV-HD2000 Expand Serial Command Functional Specifications
20/56
8.5.8. CF_SETDISPADJ Command
Command “CF_SETPCADJ_%1” [CR]
%1
“PAL”
“SECAM”
“XGA1”
“1080I60
“MODE16”
“EXT24” --------------- Etc.
Details
Apply the values set in Display adjust menu to the screen image.
When %1 in Display adjust commands (following seven commands) is directly
specified, they are not be applied to the screen image without this command.
(valid only when it is in the normal Power ON status)
.........CF_FSYNC
.........CF_TDOTS
.........CF_CLAMP
.........CF_H-POS
.........CF_V-POS
.........CF_DLINE
.........CF_DDOTS
Note) When %1 is EXT21 - EXT60, send CF_SYSTEM command. “ExMode”
should be displayed in System box.
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]
8.5.9. CF_ORGMODE Command
Command “CF_ORGMODE_%1” [CR]
%1 “XGA1” – “HDTV1080i60” ---------- Etc
Details Select the original signal of the mode set in Display adjust menu
(valid only when it is in the normal Power ON status)
Acceptable “000” [CR]
Response
Unacceptable “Error Code” [CR]