Sanyo VCC-6594P User manual

Scanning system : PAL standard (625 TV lines, 25 frames/sec.)
Interlace : PLL 2:1 interlace
Image device : 1/3 inch solid state image device CCD
Picture elements : 795 (Horizontal) x 596 (Vertical)
Effective picture elements : 752 (Horizontal) x 582 (Vertical)
Synchronizing system : Internal sync, Line lock manually switchable
Resolution : 520 TV lines horizontally, 400 TV lines vertically
Video output level : 1.0 Vp-p/75 Ω, composite
Video S/N ratio : More than 48 dB
Minimum required illumination : Approx. 0.3 lux with a F 1.2 lens (AGC, HI)
(incandescent lighting) Approx. 0.6 lux with a F 1.2 lens (AGC, NORM)
Backlight compensation : Manual MULT/CENT/OFF switching
(Active when using an auto-iris lens)
Iris function : AI/EI selectable by switches (Electronic shutter)
Electronic iris range : 0.6 lux to 50,000 lux (F1.2, lens)
Electric shutter : 7 speeds, selectable by switches: (1/50, 1/120, 1/500,
1/1000, 1/2000, 1/4000, 1/10000 sec.)
Flange-back : 12.5 mm ±0.5 mm
White balance : ATW/Manual switching
Lens mount : CS mount
AGC : HI/NORM
Environmental conditions : Temperature: -10 °C ~ + 50 °C
Humidity: less than 90 % (no condensation)
Power supply : 24 V AC, 50 Hz
Power consumption : Approx. 2.8 W (with auto iris lens)
Approx. 2.1 W (without auto iris lens)
Weight : Approx. 310 g (without lens)
Dimensions : 56 (W) mm x 45 (H) mm x 109 (D) mm
SERVICE MANUAL
COLOUR CCD Camera VCC-6594P
(Product Code : 117 108 04)
(South East Asia)
(Europe)
FILE NO.
REFERENCE No. SM5310325
L53H4/XE
NOTE : 1. Parts order must contain model number, part number, and description.
2. Substitute parts may be supplied as the service parts.
3. N. S. P. : Not available as service parts.
Design and specification are subject to change without notice.
The components designated by a symbol ( ! ) in this schematic diagram designates components whose value are of
special significance to product safety. Should any component designated by a symbol need to be replaced, use only the
part designated in the Parts List. Do not deviate from the resistance, wattage, and voltage ratings shown.
PRODUCT SAFETY NOTICE
CONTENTS
1. DISASSEMBLY ....................................2
2. BOARD LOCATION ............................. 3
3. ADJUSTMENT .....................................4
4. PARTS LIST .........................................7
SCHEMATIC DIAGRAM
SPECIFICATIONS

– 2 –
1. DISASSEMBLY
1. Loosen the two screws,
and then remove the left
and right side panels.
2. Remove the rear panel.
3. Remove the two screws,
and then pull out the top cabinet.
4. Remove the two screws, and then remove
the bracket and pull out the bottom cabinet.
5. Remove the front panel.
7. Remove the four screws, and then
disconnect the connector.
8. Remove the five screws, then remove
the CA-2/CA-3 board assemblies and
the FPC, and disconnect the connector.
9. Remove the five screws, and then
remove the lens mount bracket.
10. Remove the two
screws, and then
remove the CA-1
board assembly.
CA-3
board
CA-4 board
CA-2 board
CA-1 board
6. Remove the connector.

–3 –
2. BOARD LOCATION
CA-2 board
CA-4 board
CA-3 board
CA-1 board
TP401
S3002
ON
S3001
CA-1 board (Side B)
CA-3 board (Side A)
CA-4 board (Side B)
TP103
TP403
VR403
VR302VR303
VR301
DC
VIDEO
CT232
TP232
CA-2 board (Side B)
CT221
TP221
VR402
(Side A)

–4 –
3-3. TABLE FOR SERVICING TOOLS
Connect the adjustment jig and camera with commander cable
(VHJ-0126)
3-3-1. Computer screen during adjustment
3-4. Power Voltage Adjustment
Adjustment location: VR403 (CA-4)
Measuring location: TP403 (CA-4)
Measuring equipment: Digital voltmeter
Subject: No designation
Adjusting method:
1. Adjust with VR403 to 3.42 ±0.02 V.
3-5. Sub Carrier Frequency Adjustment
Adjustment location: CT221 (CA-2)
Measuring location: TP221 (CA-2)
Measuring equipment: Frequency counter
Subject: No designation
Adjusting method:
1. Adjust with CT221 to 4433619 Hz ±10 Hz.
3. ADJUSTMENT
3-1. ADJUSTMENT CONDITION
1. Use the 5,100K viewer for the subject.
2. Set the trigger signal of oscilloscope to VIDEO OUT, and
apply H sync unless specified.
3. Set S3002 to the “all OFF”position and S3001 to the “DC”
position.
4. In adjustments without direction to display charts, shield light
with a lens cap to provide dark condition. The amount of
light is to be stable.
5. Connect the video output to a video monitor with an input
impedance of 75 Ω.
6. Ground test point are TP103 (CA-1) and TP401 (CA-4).
7. Set the distance from the subject to about 60 cm and adjust
the camera position so that the picture frame size becomes
as shown below when performing the adjustment with the
gray scale chart (ITE gray scale chart/ γ = 0.45).
8. Apply 24 V AC to the 24 V AC terminal on the camera.
3-2. PREPARATION
1. Install the adjustment software (VHJ-0133) in a computer
running the Windows operating system.
2. Use the adjustment tool (VHJ-0127) to connect the camera
to be adjusted to the serial port of the computer, and then
turn on the power for the computer and the camera.
VIDEO OUTPUT
Commander cable (VHJ-0126)
Ref. No. Name Part code
J-1
J-2
J-3
VJ8-0007
VJ8-0009
Color viewer
Gray scale chart
Color bar chart
VJ8-0010
AGC
R GAIN
R HUE
B GAIN
B HUE
WDD
L53H Series Adjustment x
0
0
0
0
0
AUTO
STATUS
START END CLOSE
ROM CORRECTION
FILE NAME
J-4
J-5
J-6
VHJ-0126
VHJ-0133
Commander cable
Adjustment jig
Calibration software
VHJ-0127
L: Distance from CS mount to pattern (mm)
H: Pattern height (mm)
f : Lens focal length (standard 12 mm)
h: Height (4.8 mm) of CCD imaging surface
Note : The video monitor should be an under-scan TV.
L = x f –12.5 mm
(H + h)2
H x h
L
CS mount surface
CCD camera
5,100 K viewer
H

–5 –
3-9. Hue and Chroma Adjustment
Adjustment location: S3002-8 (CA-3), computer screen
Measuring location: VIDEO OUT
Measuring equipment: Oscilloscope, Vectorscope
Subject: Color bar chart
1. Display the grayscale chart on full screen.
2. Gradually move the lens aperture from the CLOSE to OPEN
side, and secure the aperture at the point where the AGC
starts to drop from the MAX setting.
3. Shield light with a lens cap, and then remove it.
4. Use the computer’s mouse to adjust each of the R GAIN, B
GAIN, R HUE and B HUE until the luminescent spot repre-
senting red is aligned with the [R] position on the vectorscope
and the luminescent spot representing yellow is aligned with
the [YL] position on the vectorscope.
5. Set the S3002 (white balance switch) to the “ATW”(OFF)
position.
3-6. 28 MHz VCO Voltage ADJUSTMENT
Adjustment location: CT232 (CA-2)
Measuring location: TP232 (CA-2)
Measuring equipment: Digital voltmeter
Subject: No designation
Adjusting method:
1. Adjust with CT232 to 8.0 ±0.2 Vp-p.
3-7. AGC Level ADJUSTMENT
Adjustment location: Computer screen
Measuring location: VIDEO OUT
Measuring equipment: Oscilloscope
Subject: Gray scale chart
Adjusting method:
1. Click the adjustment software installed from the personal
computer, and the adjustment window will be displayed.
2. Display the grayscale chart on full screen.
3. Gradually move the lens aperture from the CLOSE side to
the OPEN side, and secure the aperture at the point where
the AGC starts to drop from the MAX setting.
4. Use the computer’s mouse to adjust the AGC in the adjust-
ment window so that the video out terminal is 750 ±10 mVp-p.
3-8. White Balance Adjustment
Adjustment location: S3002-8, VR302, VR303 (CA-3)
Measuring location: VIDEO OUT
Measuring equipment: Oscilloscope, Vectorscope
Subject: Color bar chart
Adjusting method:
1. Set the S3002 (white balance swtich) to the “MANU”(ON)
position.
2. Display the grayscale chart on full screen.
3. Gradually move the lens aperture from the CLOSE side to
the OPEN side, and secure the aperture at the point where
the AGC starts to drop from the MAX setting.
4. Adjust VR302 and VR303 so that the luminescent spot rep-
resenting white is overlapping with the crosshair mark in
the center of the vectorscope.
VIDEO OUTPUT
10
45 µsec
45 µsec
R
YL
MG
Cy
G
B
75%
100%
cy
g
yl
mg
b
U
v
W

–6 –
750 ±10 mVp-p
3-12. CCD White Point Defect Detect Adjustment
Measuring location: VIDEO OUT
Measuring equipment: Monitor display
Adjustment method:
1. Shield light with a lens cap to provide dark condition.
2. Set the camera mode, and click the “AUTO”at the WDD on
the adjustment software.
3. After completing this adjustment, it comfirms that white point
can not be seen on the monitor display.
4. Click the End button.
VIDEO OUTPUT
3-10. Iris Level Adjustment
Adjustment location: S3001, VR301 (CA-3)
Measuring location: VIDEO OUT
Measuring equipment: Oscilloscope
Subject: Gray scale chart
Adjusting method:
1. Set S3001 to the DC type lens side.
2. Attach the DC type automatic iris lens. (Use a VCL-CS8LY
or equivalent as the lens).
3. Display the gray scale chart on full screen.
4. Turn the VR301 to the right so that the white level is maxi-
mum.
5. Turn the VR301 to the left so that the output level is 750 ±
10 mVp-p.
3-11. Line Phase Adjustment
Adjustment location: S3002-9 (CA-3), VR402 (CA-4)
Measuring location: VIDEO OUT, 24 V AC/GND terminals
Measuring equipment: Oscilloscope
Subject: Attach the lens cap
Adjusting method:
1. Connect the camera to a 24 V AC /50 Hz power source.
2. Set S3002-9 switch to the “L-L”(ON) position.
3. The HOT (signal) side and the COLD (GND) side of the
oscilloscope probe connect to the right side and the left side
of the 24 VAC terminals respectively. (rear view)
4. Turn VR402 (LINE PHASE) to adjust the leading edge of
the vertical sync signal and zero-cross shift of the AC 24 V
power supply to 0 ±0.2 msec.
5. Set S3002-9 to the “INT”(OFF) position before shipment.
R
YL
MG
Cy
G
B
75%
100%
cy
g
yl
mg
b
U
v
YL R
W
24 V AC
TP123
zero cross
point
0 0.2 msec.
VIDEO OUT

7
4. PARTS LIST
N.S.P.: Not available as service parts.
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
CABINET & CHASSIS PARTS
1 613 194 1182 DEC,INDICATOR
2 613 156 4015 COVER BOTTOM
3 412 051 6007 SPECIAL SCREW-3X4
4 613 159 2797 MOUNTING
5 411 126 4702 SCR PAN+SW+W 3X6
6 411 129 5102 SCR PAN+SW+W 2X5
7 613 194 1106 CABINET FRONT
8 613 197 1844 COMPL PWB,CA-4
9 412 054 3805 SPECIAL SCREW-2.0X4.0
10 613 197 3763 COVER SIDE-L
11 613 197 3756 COVER SIDE-R
12 411 126 1404 SCR S-TPG BIN 2X4
13 411 023 4201 SCR S-TPG PAN 3X10
14 613 197 1820 COMPL PWB,CA-2
15 613 197 1837 COMPL PWB,CA-3
16 411 167 1302 SCR S-TPG BIN 2X7A
17 613 197 1813 COMPL PWB,CA-1
18 613 194 1199 SPACER INSULATOR
19 613 194 2813 HOLDER CCD
20 409 498 2105 IC ICX259AK-7 (IC101)
21 613 188 0771 SPACER
22 645 050 7496 OPTICAL FILTER
23 613 194 2707 HOUSING,CRYSTAL
24 411 125 8503 SCR PAN PCS 2X4
25 613 156 4442 SPRING PLATE
26 613 156 4695 HOUSING CCD
27 613 156 4114 SLIDE
28 613 161 8350 CAM
29 613 156 4091 MOUNTING,LENS
L53X4/US PARTS LIST
1
2
4
5
6
6
6
6
7
8
9
9
9
10
11
12
13
14
15
16
16 17
18 19
20 2122 23
29
28
27
26
25
24
24
12
12
12
3
2
N.S.P.
N.S.P.

8
Note:
1. Materials of Capacitors and Resistors are abbreviated as follows ;
Resistors Capacitors
MT-FILM Metallized Film Resistor MT-POLYEST Metallized Polyester Capacitor
MT-GLAZE Metallized Glaze Resistor MT-COMPO Metallized Composite Capacitor
OXIDE-MT Oxide Metallized Film Resistor TA-SOLD Tantalum Solid Capacitor
AL-SOLID Aluminum Solid Capacitor
NP-ELECT Non-Polarized Electrolytic Capacitor
OS-SOLID Aluminum Solid Capacitors with Organic
Semiconductive Electrolytic Capacitor
DL-ELECT Double Layered Electrolytic Capacitor
2. Tolerance of Capacitor (10pF over) and Resistor are noted with follow symboles.
F ............1% G ............2% J ............5% K ............10%
M ..........20% N ..........30% Z ..........+80% ~ -20%
3. Capacitors
U :
µ FP:pF
4. Inductors
UH :
µ H MH : mH
5. N.S.P. : Not available as service parts.
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
COMPL PWB,CA-1
613 197 1813
(SEMICONDUCTORS)
Q1101 405 045 8200 TR 2SK443-6-TB
Q1102 405 079 6302 TR 2SC4399-5
(INTEGRATED CIRCUITS)
IC102 409 366 9700 IC CXD1267AN
IC103 409 427 7805 IC TC74ACT32FT
(DIODES)
D1101 407 113 5609 DIODE DSH015
(INDUCTOR)
L1101 645 003 9423 INDUCTOR,12U J
(CAPACITOR)
C1102 403 164 0204 CERAMIC 0.1U Z 25V
C1108 403 175 4109 ELECT 22U M 16V
C1109 403 175 0705 ELECT 33U M 25V
C1111 403 285 6406 TA-SOLID 1U M 35V
C1113 403 164 0204 CERAMIC 0.1U Z 25V
C1117 403 155 1807 CERAMIC 0.01U K 25V
C1118 403 285 4808 TA-SOLID 3.3U M 20V
C1124 403 164 0204 CERAMIC 0.1U Z 25V
C1125 403 143 3905 TA-SOLID 1.5U M 16V
(RESISTORS)
R1101 401 105 7503 MT-GLAZE 82K JA 1/16W
R1102 401 105 0702 MT-GLAZE 100K JA 1/16W
R1104 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R1105 401 105 4601 MT-GLAZE 3.9K JA 1/16W
R1106 401 105 8005 MT-GLAZE 1M JA 1/16W
R1113 401 105 3307 MT-GLAZE 2.7K JA 1/16W
R1116 401 105 0306 MT-GLAZE 10 JA 1/16W
R1117 401 105 0306 MT-GLAZE 10 JA 1/16W
R1118 401 105 0405 MT-GLAZE 100 JA 1/16W
R1124 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R1126 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R1133 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R1134 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
(CONNECTORS)
CN101 645 028 6025 PLUG,COAXIAL CABL(N.S.P)
CN102 645 007 7074 SOCKET,FPC 20P (N.S.P)
COMPL PWB,CA-2
613 197 1820
(SEMICONDUCTORS)
Q2001 405 092 4101 TR 2SC4081-R
Q2101 405 137 2000 TR 2SA1576A-R
Q2102 405 092 4101 TR 2SC4081-R
Q2103 405 137 2000 TR 2SA1576A-R
Q2104 405 092 4101 TR 2SC4081-R
Q2106 405 092 4101 TR 2SC4081-R
Q2107 405 092 4101 TR 2SC4081-R
Q2303 405 135 9407 TR DTA114EUA
Q2304 405 135 9407 TR DTA114EUA
Q2803 405 047 5900 TR 2SD1622-S
Q2804 405 092 4101 TR 2SC4081-R
(INTEGRATED CIRCUITS)
IC201 409 494 0204 IC AK5492
IC211 410 388 5106 IC SCC0020
IC214 409 475 2005 IC BA7664FV
IC215 409 320 9104 IC TC7SU04FU
IC216 409 323 9002 IC TC7S04FU
IC235 409 246 9707 IC LA6358NM
IC236 409 155 8105 IC TC7SU04F
IC237 409 155 8006 IC TC7S04F
IC238 409 155 8105 IC TC7SU04F
IC239 409 155 8006 IC TC7S04F
IC241 410 428 1808 IC UPD78F4225YGC-8BT
IC242 409 491 1006 IC S80827ANUP-EDQ
IC243 409 477 2102 IC BR24C02F-W
(DIODES)
D2103 407 187 5802 ZENER DIODE UDZ8.2B
D2104 407 187 5802 ZENER DIODE UDZ8.2B
D2303 407 174 1909 VARACTOR DI HVU200A4TRV
D2304 407 174 1909 VARACTOR DI HVU200A4TRV
D2401 407 113 5609 DIODE DSH015
D2801 407 065 3906 LED SLP-135B-51
(CRYSTAL DEVICES)
X2201 645 017 6050 OSC,CRYSTAL 17.734475MHZ
X2301 645 007 6947 OSC,CRYSTAL 28.375KHZ
X2401 645 045 4554 OSC,CERAMIC 5.00MHZ
(TRIMMERS)
CT221 645 005 0411 TRIMMER,30PF
CT232 645 005 0411 TRIMMER,30PF
(INDUCTORS)
L2001 645 003 9386 INDUCTOR,10U J
L2106 645 003 9522 INDUCTOR,33U J
L2110 645 003 9386 INDUCTOR,10U J
L2111 645 003 9560 INDUCTOR,68U J
L2301 645 003 9386 INDUCTOR,10U J
L2302 645 003 9546 INDUCTOR,47U J
L2304 645 004 2614 INDUCTOR,2.2U J
L2401 645 003 9386 INDUCTOR,10U J
(CAPACITORS)
C2002 403 164 0204 CERAMIC 0.1U Z 25V
C2003 403 285 3603 TA-SOLID 4.7U M 6.3V
C2004 403 164 0204 CERAMIC 0.1U Z 25V
C2005 403 164 0204 CERAMIC 0.1U Z 25V
C2006 403 164 0204 CERAMIC 0.1U Z 25V
C2007 403 164 0204 CERAMIC 0.1U Z 25V
C2008 403 164 0204 CERAMIC 0.1U Z 25V
C2009 403 164 0204 CERAMIC 0.1U Z 25V
C2011 403 164 0204 CERAMIC 0.1U Z 25V
C2012 403 164 0204 CERAMIC 0.1U Z 25V
C2013 403 164 0204 CERAMIC 0.1U Z 25V

9
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
C2014 403 164 0204 CERAMIC 0.1U Z 25V
C2015 403 285 4303 TA-SOLID 1U M 16V
C2020 403 175 3102 ELECT 100U M 4V
C2023 403 164 0204 CERAMIC 0.1U Z 25V
C2024 403 145 9905 CERAMIC 22P J 50V
C2101 403 164 0204 CERAMIC 0.1U Z 25V
C2102 403 164 0204 CERAMIC 0.1U Z 25V
C2103 403 164 0204 CERAMIC 0.1U Z 25V
C2104 403 164 0204 CERAMIC 0.1U Z 25V
C2105 403 164 0204 CERAMIC 0.1U Z 25V
C2106 403 285 3603 TA-SOLID 4.7U M 6.3V
C2107 403 164 0204 CERAMIC 0.1U Z 25V
C2108 403 164 0204 CERAMIC 0.1U Z 25V
C2109 403 164 0204 CERAMIC 0.1U Z 25V
C2112 403 164 0204 CERAMIC 0.1U Z 25V
C2113 403 164 0204 CERAMIC 0.1U Z 25V
C2114 403 164 0204 CERAMIC 0.1U Z 25V
C2115 403 145 9905 CERAMIC 22P J 50V
C2116 403 157 2307 CERAMIC 20P J 50V
C2117 403 155 1807 CERAMIC 0.01U K 25V
C2118 403 285 3603 TA-SOLID 4.7U M 6.3V
C2121 403 285 3603 TA-SOLID 4.7U M 6.3V
C2122 403 280 0508 ELECT 470U M 4V
C2123 403 145 9905 CERAMIC 22P J 50V
C2124 403 145 9905 CERAMIC 22P J 50V
C2125 403 305 0001 TA-SOLID 10U M 10V
C2127 403 232 9702 ELECT 220U M 6.3V
C2128 403 175 4505 ELECT 47U M 6.3V
C2129 403 285 4006 TA-SOLID 4.7U M 10V
C2133 403 285 5003 TA-SOLID 1U M 25V
C2135 403 285 4006 TA-SOLID 4.7U M 10V
C2136 403 164 0204 CERAMIC 0.1U Z 25V
C2137 403 093 5103 OS-SOLID 33U M 6.3V
C2138 403 164 0204 CERAMIC 0.1U Z 25V
C2153 403 155 1807 CERAMIC 0.01U K 25V
C2158 403 175 0606 ELECT 100U M 6.3V
C2159 403 285 7700 TA-SOLID 10U M 16V
C2201 403 157 2505 CERAMIC 27P J 50V
C2308 403 155 1807 CERAMIC 0.01U K 25V
C2309 403 155 1807 CERAMIC 0.01U K 25V
C2310 403 164 0204 CERAMIC 0.1U Z 25V
C2311 403 285 5003 TA-SOLID 1U M 25V
C2312 403 150 2106 NP-ELECT 4.7U M 25V
C2313 403 150 2106 NP-ELECT 4.7U M 25V
C2314 403 164 0204 CERAMIC 0.1U Z 25V
C2315 403 164 0204 CERAMIC 0.1U Z 25V
C2316 403 164 0204 CERAMIC 0.1U Z 25V
C2317 403 285 3603 TA-SOLID 4.7U M 6.3V
C2318 403 164 0204 CERAMIC 0.1U Z 25V
C2320 403 219 3907 TA-SOLID 3.3U M 25V
C2321 403 113 3805 CERAMIC 1000P K 50V
C2322 403 155 1807 CERAMIC 0.01U K 25V
C2323 403 157 1904 CERAMIC 10P D 50V
C2324 403 155 4204 CERAMIC 15P J 50V
C2325 403 164 0204 CERAMIC 0.1U Z 25V
C2327 403 285 3603 TA-SOLID 4.7U M 6.3V
C2331 403 164 0204 CERAMIC 0.1U Z 25V
C2332 403 113 3805 CERAMIC 1000P K 50V
C2333 403 113 3805 CERAMIC 1000P K 50V
C2334 403 157 1607 CERAMIC 6P D 50V
C2401 403 164 0204 CERAMIC 0.1U Z 25V
C2402 403 164 0204 CERAMIC 0.1U Z 25V
C2403 403 285 6802 TA-SOLID 10U M 6.3V
C2404 403 164 0204 CERAMIC 0.1U Z 25V
(RESISTORS)
R2001 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2002 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2003 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2004 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2005 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2006 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2007 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2008 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2009 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2012 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R2015 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R2016 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R2102 401 105 0504 MT-GLAZE 1K JA 1/16W
R2103 401 105 0504 MT-GLAZE 1K JA 1/16W
R2104 401 105 2904 MT-GLAZE 22K JA 1/16W
R2105 401 105 4205 MT-GLAZE 33K JA 1/16W
R2107 401 105 0504 MT-GLAZE 1K JA 1/16W
R2109 401 105 0504 MT-GLAZE 1K JA 1/16W
R2110 401 105 4106 MT-GALZE 3.3K JA 1/16W
R2112 401 105 1501 MT-GLAZE 1.5K JA 1/16W
R2113 401 105 5400 MT-GLAZE 47K JA 1/16W
R2114 401 105 5400 MT-GLAZE 47K JA 1/16W
R2116 401 105 0504 MT-GLAZE 1K JA 1/16W
R2119 401 113 5102 MT-GLAZE 300 JA 1/16W
R2120 401 105 4205 MT-GLAZE 33K JA 1/16W
R2121 401 105 2904 MT-GLAZE 22K JA 1/16W
R2122 401 105 0504 MT-GLAZE 1K JA 1/16W
R2123 401 105 6506 MT-GLAZE 680 JA 1/16W
R2126 401 105 1501 MT-GLAZE 1.5K JA 1/16W
R2132 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2133 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2134 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2141 401 105 0306 MT-GLAZE 10 JA 1/16W
R2142 401 158 4108 MT-GLAZE 4.7 JA 1/16W
R2143 401 105 0306 MT-GLAZE 10 JA 1/16W
R2144 401 158 4108 MT-GLAZE 4.7 JA 1/16W
R2152 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2154 401 105 8005 MT-GLAZE 1M JA 1/16W
R2156 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2159 401 219 1503 MT-FILM 68 DC 1/10W
R2201 401 105 8005 MT-GLAZE 1M JA 1/16W
R2202 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2271 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2272 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2273 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2275 401 105 0603 MT-GLAZE 10K JA 1/16W
R2311 401 105 0603 MT-GLAZE 10K JA 1/16W
R2312 401 105 0702 MT-GLAZE 100K JA 1/16W
R2313 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R2314 401 105 1907 MT-GLAZE 180 JA 1/16W
R2315 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R2316 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R2317 401 105 3000 MT-GLAZE 220K JA 1/16W
R2318 401 105 1204 MT-GLAZE 120K JA 1/16W
R2319 401 105 4700 MT-GLAZE 39K JA 1/16W
R2320 401 105 0702 MT-GLAZE 100K JA 1/16W
R2321 401 105 1204 MT-GLAZE 120K JA 1/16W
R2322 401 105 1600 MT-GLAZE 15K JA 1/16W
R2323 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R2330 401 105 5400 MT-GLAZE 47K JA 1/16W
R2331 401 105 4205 MT-GLAZE 33K JA 1/16W
R2332 401 105 0702 MT-GLAZE 100K JA 1/16W
R2333 401 105 8005 MT-GLAZE 1M JA 1/16W
R2337 401 158 4009 MT-GLAZE 3.3 JA 1/16W
R2338 401 105 0603 MT-GLAZE 10K JA 1/16W
R2339 401 105 0603 MT-GLAZE 10K JA 1/16W
R2340 401 105 0702 MT-GLAZE 100K JA 1/16W
R2341 401 105 8005 MT-GLAZE 1M JA 1/16W
R2401 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R2402 401 105 0603 MT-GLAZE 10K JA 1/16W
R2404 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2406 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2407 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2409 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2411 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2412 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2414 401 105 0603 MT-GLAZE 10K JA 1/16W
R2415 401 105 0603 MT-GLAZE 10K JA 1/16W
R2416 401 105 0603 MT-GLAZE 10K JA 1/16W
R2418 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2421 401 105 0702 MT-GLAZE 100K JA 1/16W
R2422 401 105 0702 MT-GLAZE 100K JA 1/16W
R2424 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2425 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R2801 401 105 0504 MT-GLAZE 1K JA 1/16W
R2802 401 105 0603 MT-GLAZE 10K JA 1/16W
R2803 401 038 2507 MT-GLAZE 3.3 JA 1/10W
R2804 401 038 2507 MT-GLAZE 3.3 JA 1/10W
(FILTER)
F2301 645 006 3404 FILTER,EMI 470PF

10
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
(CONNECTORS)
CN201 645 028 6025 PLUG,COAXIAL CABL(N.S.P)
CN202 645 004 9231 SOCKET,BNC 1P (N.S.P)
CN203 645 023 3319 PLUG,24P (N.S.P)
CN205 645 002 3057 PLUG,7P (N.S.P)
CN211 645 007 7074 SOCKET,FPC 20P (N.S.P)
COMPL PWB,CA-3
613 197 1837
(SEMICONDUCTORS)
Q3017 405 092 4101 TR 2SC4081-R
Q3018 405 092 4101 TR 2SC4081-R
Q3031 405 014 4509 TR 2SC2412K-R
Q3051 405 092 4101 TR 2SC4081-R
Q3131 405 092 4101 TR 2SC4081-R
Q3132 405 137 2000 TR 2SA1576A-R
Q3133 405 092 4101 TR 2SC4081-R
Q3134 405 096 2400 TR DTC144EU
(INTEGRATED CIRCUITS)
IC301 409 246 9707 IC LA6358NM
IC302 409 341 4102 IC BA7655AF
(VARIABLE RESISTORS)
VR301 645 005 5805 VR,SEMI,10K S
VR302 645 005 5805 VR,SEMI,10K S
VR303 645 005 5805 VR,SEMI,10K S
(INDUCTORS)
L3001 645 003 8983 INDUCTOR,0.22U M
L3002 645 018 3553 INDUCTOR,1000 OHM
L3003 645 018 3553 INDUCTOR,1000 OHM
L3004 645 018 3553 INDUCTOR,1000 OHM
L3005 645 018 3553 INDUCTOR,1000 OHM
(CAPACITORS)
C3011 403 285 3603 TA-SOLID 4.7U M 6.3V
C3012 403 164 0204 CERAMIC 0.1U Z 25V
C3013 403 164 0204 CERAMIC 0.1U Z 25V
C3017 403 164 0204 CERAMIC 0.1U Z 25V
C3021 403 285 3603 TA-SOLID 4.7U M 6.3V
C3028 403 172 6502 NP-ELECT 0.47U M 50V
C3029 403 175 3300 ELECT 47U M 16V
C3031 403 164 0204 CERAMIC 0.1U Z 25V
C3032 403 280 1901 ELECT 47U M 25V
C3051 403 285 3504 TA-SOLID 3.3U M 6.3V
C3052 403 285 7809 TA-SOLID 0.47U M 35V
C3121 403 164 0204 CERAMIC 0.1U Z 25V
C3123 403 283 6309 CERAMIC 1U Z 10V
C3124 403 283 6309 CERAMIC 1U Z 10V
C3125 403 283 6309 CERAMIC 1U Z 10V
C3131 403 283 6309 CERAMIC 1U Z 10V
C3132 403 164 0204 CERAMIC 0.1U Z 25V
C3201 403 164 0204 CERAMIC 0.1U Z 25V
C3202 403 164 0204 CERAMIC 0.1U Z 25V
C3301 403 164 0204 CERAMIC 0.1U Z 25V
(RESISTORS)
R3012 401 105 1105 MT-GLAZE 12K JA 1/16W
R3015 401 105 1006 MT-GLAZE 1.2K JA 1/16W
R3016 401 105 4205 MT-GLAZE 33K JA 1/16W
R3017 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R3018 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R3021 401 105 6001 MT-GLAZE 5.6K JA 1/16W
R3022 401 105 6001 MT-GLAZE 5.6K JA 1/16W
R3023 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R3028 401 105 8005 MT-GLAZE 1M JA 1/16W
R3031 401 038 3504 MT-GLAZE 330 JA 1/10W
R3032 401 038 3504 MT-GLAZE 330 JA 1/10W
R3033 401 105 0405 MT-GLAZE 100 JA 1/16W
R3051 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R3052 401 105 0504 MT-GLAZE 1K JA 1/16W
R3103 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R3105 401 105 3307 MT-GLAZE 2.7K JA 1/16W
R3109 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R3113 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R3114 401 105 2003 MT-GLAZE 1.8K JA 1/16W
R3121 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R3122 401 105 0504 MT-GLAZE 1K JA 1/16W
R3123 401 105 5400 MT-GLAZE 47K JA 1/16W
R3131 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R3132 401 105 0702 MT-GLAZE 100K JA 1/16W
R3133 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R3134 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R3135 401 105 4205 MT-GLAZE 33K JA 1/16W
R3136 401 105 4205 MT-GLAZE 33K JA 1/16W
R3301 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
(SWITCHES)
S3001 645 033 1404 SWITCH,SLIDE 4P-2T, IRIS
S3002 645 023 3883 SWITCH,DIP 1P-1TX10,
(CONNECTORS)
CN302 645 023 3326 SOCKET,24P (N.S.P)
CN304 645 043 7045 SOCKET,IRIS 4P (N.S.P)
COMPL PWB,CA-4
613 197 1844
(SEMICONDUCTORS)
Q4001 405 047 5900 TR 2SD1622-S
Q4002 405 092 4101 TR 2SC4081-R
Q4003 405 137 2000 TR 2SA1576A-R
Q4211 405 137 2000 TR 2SA1576A-R
Q4212 405 129 9901 TR UMW2N
(INTEGRATED CIRCUITS)
IC402 409 475 2104 IC LT1172HVCT/FLOW31
IC403 409 167 7202 IC NJM2406F
(DIODES)
D4001 407 103 0409 DIODE DBB08C
D4002 407 099 8700 ZENER DIODE MTZJ24B
D4003 407 066 8702 DIODE SB10-05PCP
D4004 407 066 8702 DIODE SB10-05PCP
D4005 407 066 8702 DIODE SB10-05PCP
D4006 407 222 4500 DIODE 1SR156-400
D4007 407 066 8702 DIODE SB10-05PCP
D4008 407 066 8702 DIODE SB10-05PCP
D4101 407 173 1108 PHOTO COUPLE TLP181-GB
(VARIABLE RESISTORS)
VR402 613 002 1557 SEMI VR
VR403 645 003 7597 VR,SEMI,3.3K N
(INDUCTORS)
L4001 645 003 9591 INDUCTOR,100U K
L4002 645 041 9355 INDUCTOR,100U K
L4003 645 041 9355 INDUCTOR,100U K
L4005 645 003 9591 INDUCTOR,100U K
(TRANSFORMER)
T4001 645 051 5323 TRANS,POWER,PULSE
(CAPACITORS)
C4001 403 232 9405 CERAMIC 0.01U Z 1KV
C4002 403 232 9405 CERAMIC 0.01U Z 1KV
C4003 403 114 5204 POLYESTER 0.01U K 250V
C4004 403 190 5402 ELECT 100U M 50V
C4005 403 285 7502 TA-SOLID 0.1U M 35V
C4006 403 211 8801 ELECT 470U M 50V
C4007 403 157 3601 CERAMIC 100P J 50V
C4008 403 157 3601 CERAMIC 100P J 50V
C4009 403 157 3601 CERAMIC 100P J 50V
C4010 403 164 0204 CERAMIC 0.1U Z 25V
C4011 403 337 7207 ELECT 33U M 35V
C4012 403 337 4107 ELECT 100U M 25V
C4013 403 164 0204 CERAMIC 0.1U Z 25V
C4014 403 093 7602 OS-SOLID 33U M 10V
C4015 403 333 2602 ELECT 220U M 10V
C4016 403 333 2602 ELECT 220U M 10V
C4017 403 333 2602 ELECT 220U M 10V
C4018 403 337 7207 ELECT 33U M 35V
C4019 403 164 0204 CERAMIC 0.1U Z 25V
C4020 403 285 6307 TA-SOLID 0.22U M 35V
C4021 403 155 1807 CERAMIC 0.01U K 25V
C4022 403 285 6307 TA-SOLID 0.22U M 35V
C4023 403 285 5003 TA-SOLID 1U M 25V
C4024 403 232 9702 ELECT 220U M 6.3V
C4025 403 164 0204 CERAMIC 0.1U Z 25V
C4026 403 164 0204 CERAMIC 0.1U Z 25V
C4027 403 215 1006 CERAMIC 470P J 50V
C4028 403 345 6100 ELECT 47U M 25V
C4041 403 232 9405 CERAMIC 0.01U Z 1KV

11
Core A (645 052 1997) Core B (645 052 1980)
LOCATION PARTS NO. DESCRIPTION
C4042 403 334 7606 ELECT 47U M 50V
C4043 403 337 7207 ELECT 33U M 35V
C4044 403 164 0204 CERAMIC 0.1U Z 25V
C4045 403 164 0204 CERAMIC 0.1U Z 25V
C4211 403 113 3805 CERAMIC 1000P K 50V
(RESISTORS)
R4001 401 038 6406 MT-GLAZE 4.7K JA 1/10W
R4002 401 038 6406 MT-GLAZE 4.7K JA 1/10W
R4003 401 037 5400 MT-GLAZE 1K JA 1/10W
R4004 401 038 3504 MT-GLAZE 330 JA 1/10W
R4005 401 177 2703 MT-GLAZE 6.8 JA 1/16W
R4007 401 105 1006 MT-GLAZE 1.2K JA 1/16W
R4008 401 105 3208 MT-GLAZE 270 JA 1/16W
R4009 401 105 0405 MT-GLAZE 100 JA 1/16W
R4010 401 105 0405 MT-GLAZE 100 JA 1/16W
R4011 401 105 0405 MT-GLAZE 100 JA 1/16W
R4012 401 038 5003 MT-GLAZE 390 JA 1/10W
R4014 401 038 3603 MT-GLAZE 3.3K JA 1/10W
R4015 401 105 1501 MT-GLAZE 1.5K JA 1/16W
R4016 401 105 0504 MT-GLAZE 1K JA 1/16W
R4017 401 105 6605 MT-GLAZE 6.8K JA 1/16W
R4018 401 037 5004 MT-GLAZE 0.000 ZA 1/10W
R4020 401 105 0702 MT-GLAZE 100K JA 1/16W
R4021 401 105 0702 MT-GLAZE 100K JA 1/16W
R4022 401 105 6001 MT-GLAZE 5.6K JA 1/16W
R4023 401 105 4205 MT-GLAZE 33K JA 1/16W
R4024 401 105 1600 MT-GLAZE 15K JA 1/16W
R4025 401 105 0603 MT-GLAZE 10K JA 1/16W
R4026 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R4027 401 105 6001 MT-GLAZE 5.6K JA 1/16W
R4028 401 105 0504 MT-GLAZE 1K JA 1/16W
R4029 401 105 0405 MT-GLAZE 100 JA 1/16W
R4030 401 105 1600 MT-GLAZE 15K JA 1/16W
R4031 401 105 1501 MT-GLAZE 1.5K JA 1/16W
R4034 401 037 5004 MT-GLAZE 0.000 ZA 1/10W
R4051 401 038 3603 MT-GLAZE 3.3K JA 1/10W
R4052 401 038 3603 MT-GLAZE 3.3K JA 1/10W
R4053 401 038 3603 MT-GLAZE 3.3K JA 1/10W
R4211 401 286 3905 OXIDE-MT 1.2 JA 1/2W
R4212 401 037 5400 MT-GLAZE 1K JA 1/10W
(CONNECTORS)
CN401 645 018 2112 TERMINAL (N.S.P)
CN402 645 002 3071 PLUG,9P (N.S.P)
FLEXIBL FLAT CABLE
W1001 636 025 0079 FFC,47 20 1.0
ACCESSORIES & PACKING MATERIAL
636 009 7841 LENS CAP
613 195 9422 INSTRUCTION MANUAL
645 040 7857 PLUG,IRIS 4P
645 052 1997 CORE,FERRITE (Core A)
645 052 1980 CORE,FERRITE (Core B)
613 197 6160 CARTON CASE INNER
613 182 9343 CUSHION BAG
613 197 6177 CARTON CASE OUTER

Oct./’01
SANYO Electric Co., Ltd.
Osaka, Japan

BLOCK DIAGRAMS,CIRCUIT DIAGRAMS &
PRINTED WIRING BOARDS
TABLE OF CONTENTS
OVERALL WIRING, BLOCK DIAGRAM & CIRCUIT DIAGRAMS
OVERALL WIRING C1
OVERALL CIRCUIT BLOCK DIAGRAM C2
CA-1 CIRCUIT WAVEFORMS
CA-1 CIRCUIT C3
IC101, IC102, IC103, IC201 & IC211 BLOCK DIAGRAMS C4
CA-2 CIRCUIT WAVEFORMS
CA-2 CIRCUIT C5
CA-3 CIRCUIT C6
CA-3 CIRCUIT WAVEFORM
CA-4 CIRCUIT C7
PRINTED WIRING BOARDS (P.W.B.)
CA-1 BOARD (SIDE A & B) C8
CA-2 BOARD (SIDE A & B)
CA-3 BOARD (SIDE A & B) C9
CA-4 BOARD (SIDE A & B)

NOTES:
1. All resistance values in "OHMS" unless otherwise noted.
(K=1,000 ; M=1,000,000)
2. All capacitance values in "µF" unless otherwise noted.
p=pico farad ; µ,u or U=micro farad
3. All inductance values in "µH" unless otherwise noted.
µ,u or U=micro henry ; m=milli henry
PRODUCT SAFETY NOTICE
THE COMPONENTS DESIGNATED BY A SYMBOL ( ) IN THIS
SCHEMATIC DIAGRAM DESIGNATES COMPONENTS WHOSE
VALUE ARE OF SPECIAL SIGNIFICANCE TO PRODUCT SAFETY.
SHOULD ANY COMPONENT DESIGNATED BY A SYMBOL NEED TO
BE REPLACED, USE ONLY THE PART DESIGNATED IN THE PARTS
LIST.
DO NOT DEVIATE FROM THE RESISTANCE, WATTAGE AND VOLT-
AGE RATINGS SHOWN.
PAL-C-EX
EXPLANATORY NOTES (EXAMPLES)
Resistor 10K:1/16J means 10kilo ohm ±5%, 1/16watt max.
1M:1/10K means 1mega ohm ±10%, 1/10watt max.
Capacitor 0.047:F means 0.047micro farad, Ftype.
Electrolytic capacitor
10:16 means 10micro farad, 16volt max.
Inductor 330:J means 330micro henry ±5%
470:K means 470micro henry ±10%
No description J or K means ±5%

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C1
OVERALL WIRING, BLOCK DIAGRAM & CIRCUIT DIAGRAMS
OVERALL WIRING

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C2
OVERALL CIRCUIT BLOCK DIAGRAM
WAVEFORM
TEST
LOCATION
WAVEFORM
TEST
LOCATION
IC101-1
5V/div 20µs/div
V4
IC101-2
5V/div 20µs/div
V3
IC101-3
5V/div 20µs/div V2
IC101-15,16
2V/div 50ns/div
H1,H2
IC101-4
5V/div 20µs/div
V1
IC101-13
2V/div 50ns/div RG
WF-CA1-L53X4XE
CA-1 CIRCUIT WAVEFORMS

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C3
CA-1 CIRCUIT

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C4
DAC
C
DAC
Y
CLP
CLPOB
PBLK
H1 H2
RG
V1 V2 V3 V4
XSG1 XSG2
VSUB
PCOHD
ZRST
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
ZRD
ZWR
ALE
SHP
SHD
ADCK
CKI1
HRST
VRST
SCK
VDO
HSYNC/ CSYNC
FLDO
TESTO
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
100
99 98 97 96 95 94 93 92 91 90 79 78 77 76 89 88 87 86 85 84 83 82 81 80
75 69 68 67 66 65 64 63 62 61 6074 73 72 71 70 59 58 57 56 55 54 53 52 51
CCDI0
CCDI1
CCDI2
CCDI3
CCDI4
CCDI5
CCDI6
CCDI7
CCDI8
CCDI9
TG
SG1
Video Select
OSC
INV
Phase CMP2
Phase
CMP1
2H LINE MEMORY
YC
Process
and
Seperation
Color Encode
VIDEO MEMORY
1/ 4
1H
Counter
BF
AVDD
YAOUT
AGND
CPU
I/F
VCC
GND GND
VCC1
VCC
GND GND
GND
VCC1
GND
GND
VCC1
GND
VCC
VCC
GND
AGND
CAOUT
AVDD
GND GND GND GND
SMC
SIN/ ZCS
SOT/ CPUCK
GND CKSCI CKSCO SCO ADJSCI EXTSCI PCOSC VCC2 GND VCC2 GND SCI
S
E
L
GND
GND
GND
GND
GND
TMC1
TMC2
TEB
BUNRI
AMC
CKI2
PCOVD
Data pass
SG2
1
2
3
4
5
6
7
8
910 11 12 13 14 15 16
(NOTE)
(NOTE : PHOTO SENSOR)
V
OUT
V
SS
V GG
GND
1
2
3
4
V
DD
GND
SUB
V
L
RG
1
1
2
H RERISTER
Cy Ye Cy Ye
Mg GMg G
Cy Ye Cy Ye
GMgGMg
Cy Ye Cy Ye
MgGMgG
V RERISTER
V RERISTER
V RERISTER
V RERISTER
Charge Pump
CPP3
V
H
DCIN
XSHT
XV2 XV1
XSG1
XV3
XSG2
XV4
CPP1
CPP2
DCOUT
VSHT
V
L
V
M
2
3
4
5
6
7
8
9
10 11
12
13
14
15
16
17
18
19
20
1
SERIAL
REG.
10BIT
ADC
CCD
REFIN
CCDIN
TIMING
GENERATOR
DC CLAMP
DO0..DO9
SHR SHD
CDS
MONOUT
ROUGH
PGA PGA
FINE
(2BIT) (2BIT) (6BIT)
ADIN
S/H
CLPCAP
OBCAP
AISET
ADCK
+
BANDGAP
VREF VRP
VCOM
VRN
COMPARE
REG(7BIT).
DAC
CCDCLP
OBP
BLK OBP CCDCLP CSN SCK SDATA RESETN STBYN
AVDD1 AVDD2 AVDD3 AVDD4 AVSS1 AVSS2 AVSS3 DVDD DVSS
CLPCAP
ADCLP
ADCLP
OUTCK
IC101 BLOCK DIAGRAM (ICX259AK)
IC102 BLOCK DIAGRAM (CXD1267AN)
IC103 BLOCK DIAGRAM (TC74ACT32FT)
IC201 BLOCK DIAGRAM (AK5492)
IC211 BLOCK DIAGRAM (SCC0020)
CA-2 CIRCUIT WAVEFORMS
WAVEFORM
TEST
LOCATION
TEST
LOCATION WAVEFORM
IC211-47
1V/div 5ms/div VD
IC201-11
0.5V/div 10µs/div CCD IN
IC211-79
1V/div 50ns/div ADCK
IC211-42
200mV/div 10µs/div CA OUT
IC211-55
200mV/div 10µs/div YA OUT
IC211-31
0.5V/div 50ns/div CKSCO
WF-CA2-L53X4US
IC211-85
2V/div 10µs/div PBLK
IC201-23,24
1V/div 50ns/div SHD,SHR

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C5
CA-2 CIRCUIT

A B C D E F G H I J K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
A B C D E F G H
I
J
K
C6
CA-3 CIRCUIT
WAVEFORM
TEST
LOCATION
S3001-4
0.5V/div 2ms/div
(VIDEO TYPE LENS)
WF-CA3-L53X4US
CA-3 CIRCUIT WAVEFORM