Sapling SMC 3000 Series User manual

Page 1
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
MOUNTING
Surface Mounting Diagram..…………………………………………………………… Page 2
Rack Mounting Diagram……………………………………………………………….. Page 3
BOARD LAYOUT
Board Layout…….……………………………………………………………………… Page 4
INTERFACING
Interfacing With Other Sapling Master Clocks…………………………………………. Page 5
SYNCHRONOUS CORRECTION CODES
Synchronous Correction Code Chart…………………………………..………………... Page 6
WIRING DIAGRAMS
Wiring Diagrams………………………………………………………………………… Pages 7 - 13
INTERFACING
Interfacing With Other Systems………………………………………………………… Pages 14 - 17
FREQUENTLY ASKED QUESTIONS
SMC 3000 Frequently Asked Questions………………………………………………… Page 18
TROUBLESHOOTING
SMC 3000 Troubleshooting…………………………………………………………….. Page 19
Table of Contents

Page 2
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
Surface Mounting Diagram

Page 3
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
Rack Mounting Diagram

Page 4
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
Board Layout

Page 5
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
Interfacing Between Master Clocks

Page 6
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
Synchronous Protocol Information
Protocol
Type Correction Code Hourly Correction
Duration
Daily
Correction
Time
Daily
Correction
Duration
59 minute correction
Simplex 2310-92XX 57 and 77 series
IBM 57, 62, 77, 82 and 87 series
Cincinnati D10 and D12
Latham SS12 types
Edwards 01
Dukane 24SS series
006
8 seconds
05:57:54
17:57:53
Will correct
hours, minutes,
and seconds.
14 seconds
Dukane 24030,24023,24050, 24060 and
24010 types
National Time & Rauland
Rauland Analog 2460 series
National 010-NNE-SRAX,
010-NNE-SRAXLV,
023-NNE-SRAX,
023-NNE-SRAXLV,
030-NNE-SRAX,
030-NNE-SRAXLV,
060-12E-SRAX,
060-12E-SRAXLV
001 or 002
25 seconds
06:00:00
18:00:00
Will correct
hours, minutes,
and seconds.
001 = 25 seconds
on, 35 seconds
off every minute
for 24 minutes.
002 = 24 minute
closure from
6:00:25 to
6:24:25 AM &
PM
Stromberg E3109 and WS310
003 10 seconds
11:56:00
23:56:00
Will correct
hours, minutes,
and seconds.
45 seconds
National, 010-NNE-SR,
010-NNE-SRLV
023-NNE-SR,
023-NNE-SRLV
030-NNE-SR
030-NNE-SRLV
060-12E-SR
060-12E-SRLV
020 25 seconds N/A
N/A
Hourly
Correction
Time
xx:57:54
Will correct
the minutes
and
seconds.
xx:00:00
Will correct
the minutes
and seconds.
xx:56:05
Will correct
the minutes
and seconds.
xx:00:00
Dukane 24BF209, 24BF212 707-8 and
707-9 types
005
xx:57:03
Will correct
the minutes
and seconds.
xx:58:05
57 seconds
5:59:03
17:59:03
Will correct for
hours, minutes,
and seconds.
57 seconds on,
63 seconds off
11 times from
5:59:03 to
6:20:00
58 minute correction
Honeywell ST402, 403, 404, 410, 411,
412, 413, 802, 803, 804, 810, 811, 812
& 813
Faraday 1310, 1311, 1320, & 1321
Cincinnati D8
Standard/Faraday 2310 & 2331
007 xx:58:05
Will correct
the minutes
and seconds.
55 seconds
5:05:00
17:05:00 65 seconds on, 25 seconds off
12 times from
5:05:00 to
5:22:35

Page 7
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Page 8
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Page 9
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Page 10
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Page 11
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Page 12
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Page 13
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com

Page 14
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
Slave Input Mode
Address 070: Slave input mode
(Please see diagrams below for wiring information and instructions)
000 Off
001 Midnight Reset / Once a Day Pulse
Address 72 = Hour, Address 73 = Minute, Address 74 = Second
003 59 minute synchronous
004 58 minute synchronous
005 National Time and Rauland analog
006 Rauland Systems digital
Address 075: Impulse clock mode
With the clock powered down, switch jumpers S2 and S4 on the relay board to S1 and S3.
Power up the clock with the 50 watt power supply installed (part # SMC-000-010-1). Pins 25
and 26 will power up the impulse clocks. The time on the slave clock has to be entered in
programming so the master clock will send out the correct amount of pulses to correct the
clock.
Once you have entered all required information, press the <NO/CANCEL> key to exit pro-
gramming mode.
MIDNIGHT RESET:
Applying a minimum of two-second pulse will bring the master clock to the correct time.
Instructions:
1. Set address 070 to “001”
2. Input the exact time (in hour, minute, second) that the clock should reset to when it receives
the correction pulse. This data is entered into Addresses 072, 073 and 074 as shown in
diagram above.
3. Connect input as shown in the diagram
4. Apply power to the clock.
Interfacing With Other Systems

Page 15
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
59 MINUTE CORRECTION
110 VAC/24 VAC 60 Hz is used to run the clock normally. Applying an eight (8) second reset
signal from 57 minutes and 54 seconds will cause an hourly correction. Applying a fourteen
(14) second reset signal from 5:57:54 will cause a daily correction.
Instructions:
1. Set address 070 to “003”
2. Connect input as shown in the diagram.
3. Apply power to the clock.
58 MINUTE CORRECTION
110 VAC/24 VAC 60 Hz is used to run the clock normally. Applying a 55 second reset sig-
nal from 58 minutes and 05 seconds will cause an hourly correction. Applying a 55 second
reset signal when hours equal 05 or 17 and minutes equal 03, 07, 11, 15, 19, 23, 31, 35, 43 or
47 and seconds equals 05 will cause a daily correction.
Instructions:
1. Set address 070 to “004”
2. Connect input as shown in the diagram.
3. Apply power to the clock.
Interfacing With Other Systems

Page 16
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
NATIONAL TIME and RAULAND CORRECTION (Analog Clocks)
110 VAC/24 VAC 60 Hz is used to run the clock normally. Applying a 25 second reset signal
when minutes equal 00 and seconds equal 00 will cause an hourly correction. Applying a 24
minute reset signal when hours equal 06 or 18 and minutes equal 00 and seconds equals 25
will cause a daily correction.
Instructions:
1. Set address 070 to “005”
2. Connect input as shown in the diagram.
3. Apply power to the clock.
RAULAND SYSTEMS CORRECTION (Digital Output)
Applying a half second pulse for every minute to the Dig. Line will bring the clock to the cor-
rect time. The clock will jump to the correct time at the end of the correction pulse.
Instructions:
1. Set address 070 to “006”
2. Connect input as shown in the diagram.
3. Apply power to the clock.
Synchronous Protocol Information

Page 17
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
This function can only be used when running a digital clock system (either SBD 1000 or
SBD 2000).
Instructions:
1. Connect input as shown in the diagram.
2. Apply power to the clock.
RS232 Interfacing
Fire Alarm System Interfacing

Page 18
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
What systems can I run off of the SMC 3000 Series Master Clock?
The SMC 3000 Series master clock can run 59 minute correction, 58 minute correction, Na-
tional Time and Rauland, 2 and 3 wire digital communication (with optional auxiliary power
supply installed), and Sapling RS485 systems.
Can I interface the SMC 3000 with a computer?
Yes, through the RS232 output on the master clock. The SMC 3000 also has software called
MEDITOR which allows the user to enter, edit, and delete schedules and schedule changes
through a Windows based program.
How many events can I schedule into the master clock?
There can be up to 800 events scheduled in the master clock.
I have to have a bell system in the school. How many relays are available in the SMC 3000
Series master clock?
There are four (4) relays standard with the master clock. The SMC 3000 master clock can util-
ize up to twelve (12) relays total.
What voltage can I use to power the SMC 3000 Master Clock?
The SMC 3000 master clock can be powered using 110 VAC/60 Hz or 220 VAC/50 Hz.
Will the master clock lose all of my settings if power is removed?
No, the SMC 3000 has a non-volatile EEPROM that ensures that the information stored will not
be lost.
Is there anyway I can test to see if a relay is working?
Yes, through BIT testing, every aspect of the master clock can be tested to make sure everything
is running optimally. For more information on BIT testing, please refer to the SMC 3000 pro-
gramming manual.
Does the SMC 3000 have built-in bells?
No. The SMC 3000 does not contain any bells. It provides the relay closures for bell systems.
Bells or tone generators must be purchased through a third party.
Frequently Asked Question

Page 19
SMC 3000 Series Master Clock Installation Manual(V2)
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: [phone] Fax: [phone] www.Sapling-Inc.com
What should I do if the master clock is not powering up?
Measure the voltage between pins one (1) & three (3). The voltmeter should read 85 - 135
VAC between the hot and the neutral.
I’m trying to control my SMC 3000 by using a Rauland master clock, but it doesn’t
seem to be working. What should I do?
Make sure the SMC 3000 is wired correctly to make sure it is capable of receiving the input.
Also, make sure Address 070 is set to the right protocol.
My synchronous clock system is not correcting. What should I do?
Make sure the right correction code is inputted into the master clock circuit. Please refer to
page 6 for details.
My 2 wire system doesn’t seem to be working. How can I test the signal of the 2 wire
digital communication circuit?
First, make sure the auxiliary power supply was installed (part number SMC-000-010-1). If
the power supply is correctly installed, then put the voltmeter on DC voltage. Measure be-
tween pins 25 and 26 and verify that you have a pulsating 24 volts. If you do not have volt-
age there, contact Sapling technical support.
I’m interfacing the master clock with the GPS receiver. The master clock doesn’t
seem to correct. What should I do?
Make sure the polarity for the RS485 is correct coming from the GPS. If the polarity is re-
versed, the master clock will not correct.
The relay isn’t closing for my bell system. How do I know if it’s working?
The SMC 3000 has a self-testing feature called BIT testing. This will test all aspects of the
master clock. Enter BIT testing and test the relay. For more information on how to enter
BIT testing, please refer to the SMC 3000 programming manual.
Troubleshooting