Sapling SBD Series User manual

The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA
P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com
Installation Manual V11.0
SBD Series Clock

The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA
P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com
2
Manuals may change without prior notice
SBD Series Clock - Table of Contents
Interactive Hyperlinked PDF – Click on the topic and the document will go to the relevant page.
Clicking on the logo will take you back to the table of contents.
Table of Contents 2
Important Safety Instructions 3
Identify Your Clock 4 - 5
Preparing for the Installation 6
Flush Mounted Clock Mechanical Installation 7 - 9
Wall Mounted Clock Mechanical Installation 10 - 14
Dual-Faced / Flag Mounted Digital Clocks Overview 15
Dual-Faced / Flag Mounted Clock Mechanical Installation 16 - 23
Uniform Stage Installation 24 - 26
Jumper Switch Settings 27
Temperature Sensor Installation (3200/3300 Only) 28
Buzzer Installation (3300 Only) 29
Wiring Instructions 30
- 2-Wire Digital Communication Protocol 31
- RS485 Communication Protocol 32
- Sync-Wire 110/230VAC Communication Protocol 33
- Sync-Wire 24VAC Communication Protocol 34
- Connecting to the Clock 35
Time Input - Clock Settings
- Sync-Wire Communication Protocol (3300 Only) 36 - 39
Inputs - Clock Settings - User Inputs (3300 Only) 40
Outputs (3300 Only) 41
Manual Controls (3300 Only) 42 - 48
Accessing the Clock After it has been Installed 49
sbdconfig Installation 50 - 58
- Task Bar 59 - 60
- Display Settings 61
- Brightness Schedule 62
- Clock Settings 63
- Outputs 64
- Elapsed Timer 65
- Inputs 66 - 67
- Daylight Saving Time (DST) 68
Reading the Display 69
Frequently Asked Questions 70
Troubleshooting 71
Warranty 72
Available with 3200 and 3300 models
Available with 3300 model only

The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA
P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com
Important Safety Instructions
3
NOTICE
• Do not install the clock outdoors.
Damage to the clock if placed outdoors
voids the warranty.
• Do not hang objects from the clock or clock
mounting parts. The clocks are not designed
to support the weight of other objects.
• The clock face and housing may be cleaned
with a damp cloth or disinfectant. Test
other cleaning products on a small part of
the clock housing before attempting to use
on the rest of the clock. Avoid bleach and
chemicals known to dissolve plastics.
VERY IMPORTANT:
KNOW YOUR COMMUNICATION PROTOCOL
Depending on its series (3100, 3200 or 3300) the SBD clock supports different time protocols. In order
to properly function and synchronize, it is very important to follow the correct wiring diagram which is
provided in this manual. For example: if your system includes converter boxes which are only used for the
2-wire system, then you should only follow the instructions that relate to the 2-wire digital communication
protocol wiring.
WARNING
FIRE HAZARD
• Always follow your national and regional
electrical codes or ordinances.
• The AC power circuit for the clock must
be attached to a circuit breaker that can
be reset by the user.
PHYSICAL INJURY HAZARD
• If you are standing on an object while
installing your clock, make sure that the
object can support your weight, and will not
sway or move as you stand on it.
• Take precautions to avoid injury by potential
safety hazards near the point of installation
including (but not limited to) heavy
machinery, sharp objects, hot surfaces, or
exposed cables carrying an electric current.
• Follow all mounting instructions exactly as
stated in this manual. Failure to do so may
result in the device falling off the point of
installation.
• Packaging materials and mounting items
include plastic bags and small pieces, which
pose a suffocation hazard to young children.
DANGER
SHOCK HAZARD
• Keep the electricity to this device turned
OFF until the clock installation
is complete.
• Do not expose the clock movement to
water, or install the clock in a location
where it may be exposed to water.

4
The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA
P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com
Identify Your Clock
A label containing the part number of your clock is attached to the clock packaging
If your part number begins with SBD-31, it is a 3100 Series clock
If your part number begins with SBD-32, it is a 3200 Series clock
If your part number begins with SBD-33. it is a 3300 Series clock
If the second group in your part number ends in S (31S, 32S, 33S), it is a Surface Mount Clock, which can
be attached to a pole as a Flag Mount or a Double Mount.
If the second group in your part number ends in F (31F, 32F, 33F), it is a Flush Mount Clock, which can only
be used in a flush mount configuration.
VERY IMPORTANT:
The SBD Wired Digital Clock supports different Time Protocols and is offered at different voltage inputs.
Familiarize yourself with the specific clock wiring diagram that is relevant to your wired clock system so that
the pre-wiring in the wall is correctly done and matches the type of wired clock system used. The different
wiring diagrams and instructions are presented in this manual.

5
The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA
P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com
The digital clocks are offered at either 3100, 3200, or 3300 Series number. The higher the series
number indicates that the clock has higher feature set and capabilities.
3100 Series clock electric board layout:
3200 Series clock electric board layout:
3300 Series clock electric board layout:
Additional Ports
Interface Port for
USB Programming
Cable or RS485 Sync
Environment
Relay Output Ports
Identify Your Clock
Interface Port for Elapsed
Timer Control Panel or
Temperature Sensor Port
Interface Port for Elapsed
Timer Control Panel or
Temperature Sensor Port
Interface Port for
USB Programming
Cable or RS485 Sync
Environment
Power Connector
Power Connector
Power Connector

6
The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA
P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com
Preparing for the Installation
Consideration should be made for various factors such as their location, type of mounting (flush, surface, dual-
faced or flag mounted), electrical wiring run, and more. Please read the manual including all relevant sections
for your specific installation configuration to understand the steps, how to wire, and how to install the clock. In
addition, please note what hardware you may need to supply.
The clock can be Flush Mounted (for inside the wall installation), Surface (wall) Mounted, Dual-Faced or
Flag Mounted.
Mounting the clock housing for these different configurations is different from one another; however, clock
display installation and wiring is similar. Therefore, each mounting will have its own initial installation instructions
section followed by a “Uniform Stage Installation” section.
For installing the clocks, the installer will need to have the below items which are not provided with the clocks:
• A #2 Phillips-head screwdriver
• Electrical wires for power (Recommended 12, 14 or 16 AWG)
• A drill and a drill bit (size depending on wall anchor)
• A flat-head screwdriver
In Addition:
For a Flush Mounted Clock:
• There are multiple holes in the clock metal back box that would accommodate (up to) size #10 screws
for fixating it to the wall. Hardware to fixate the clock’s metal back box to the wall, depending on the
type of wall, is to be provided by the installer.
For a Surface (wall) Mounted Clock:
• A double gang (utility) box
For a Dual-Faced or a Flag Mounted Clock:
• A double gang (utility) box
• There are 4 holes in the pole base plate that would accommodate size #8 screws for fixating it to the
ceiling or to the wall. Hardware to fixate the pole base plate to the ceiling or to the wall depending on
the type of wall is to be provided by the installer.

7
The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA
P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com
Flush Mounted Clock Mechanical Installation
Included in Package
Included with the Clock Wiring Kit
Power/grounding wire harness
and connector
Grounding wire
#6-32x1/2 Phillips flat head black
machine screw
Hex nut 6-32
#6 Internal-tooth lock washer
1
1
4
1
1
Description
SBD Digital Clock
Digital Clock
Quantity
1
1
Picture
or
110V / 230V 24V
Flush Mount Housing
(for inside the wall installation)

12
34
8
The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA
P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com
[
3) Once a hole in the wall is cut, place the clock
gang box in the wall and make sure that it is leveled
with the floor. You may need to make a fixture
to secure the gang box in between the studs in
the wall, nail it to the cinderblock, or take needed
actions to secure it to the wall depending on the
type of wall. The gang box has pre-punched holes
on all sides, allowing to secure the gang box to the
wall.
Flush Mounted Clock Mechanical Installation
1) This clock is offered at different sizes and
based on its size, its metal back gang box will be
compatible with its display size. Once you have the
flush mounted housing (dimensions are available in
the specifications), cut a hole in the wall, making
sure to leave at least 1.0” (2.54 cm) between the
top of the clock gang box and the celling.
4) Since the flush mounted digital clocks are offered
at different voltages and are made out of metal,
depending on the local codes and regulations, you
may also need to ground the clock gang box to the
facility grounding bus using the provided hex nut
and internal-tooth lock washer.
2) Plan where the wires are going to be run into
the clock and knockout the semi pre-punched
designated wiring holes on the clock gang box.
The clock gang box comes with semi pre-punched
wiring holes in all sides.
1.0” [ 1.0”
grounding wire included in wiring kit
x = knockout holes for wiring
y = nailing holes for securing the gang box to the wall
x x
xx
xx
xx
y
y
yy
yy
yy
y
y
y
y

5
6 7
9
The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA
P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com
Flush Mounted Clock Mechanical Installation
5) Run the power / data wires from the wall into the clock gang box through one of the knockout holes
as shown in the below image.
6) To proceed with the installation instructions,
please follow the “Uniform Stage Installation”
section in this manual. Once done, to complete the
flush mounted clock installation, follow step 7.
7) With the clock powered and properly
functioning, the last step would be to remove the
adhesive clear protective film from the clock filter,
as shown in the below image.

10
The Sapling Company, Inc.
670 Louis Drive
Warminster, PA 18974
USA
P. (+1) 215.322.6063
F. (+1) 215.322.8498
www.sapling-inc.com
Wall Mounted Clock Mechanical Installation
Included in Package
Description
SBD Digital Clock
Digital Clock Wall Housing
#6-19x1/2 screw
#6-32x1 screw
Quantity
1
1
4
4
Picture
Included with the Clock Wiring Kit
If not mounting the clock to a double gang box, the installer needs to provide:
Power/grounding wires
and connector
1
#8 self-tapping screws
Wall anchors
or
110V / 230V 24V
4
4