Sapling SBL 3000 Series Assembly instructions

SBL 3000 Series Wireless Clock
The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
Installation and Programming Manual V7

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
2
Table of Contents
SBL 3000 Series Wireless Clock
Table of Contents—2
Installation
Included in the Kit—3
ABS Surface (Wall) Mount Installation—4
ABS Surface (Wall) Mount Installation (continued)—5
ABS Double Mount Installation—6
ABS Double Mount Installation (continued)—7
ABS Double Mount Installation (continued)—8
Wiring Information
Wiring and Jumper Settings (3100 Series)—9
Wiring and Jumper Settings (3200 Series)—10
Wiring and Jumper Settings (3300 Series)—11
Using the Output Sync Relay on the SBL 3300—12
Temperature Sensor Wiring (Optional)—13
Buzzer Installation (3300 Series)—14
Programming
Setting the Time on the SBL 3300 - Programming the SBL 3300—15
Programming the SBL 3300 (continued)—15-22
Software
Installing the Sbdconfig.exe Software—23-26
Sbdconfig Software - Task Bar Functionality—27-28
Sbdconfig Software - Display Settings—29
Sbdconfig Software - Brightness Schedule—30
Sbdconfig Software - Clock Settings—31
Sbdconfig Software - Outputs—32
Sbdconfig Software - Elapsed Timer—33-35
Sbdconfig Software - Inputs—36-37
Sbdconfig Software - DST—38-39
Support
Reading the Display—40
Frequently Asked Questions—41
Troubleshooting—42
FCC Statements—43
*Manuals may change without prior notice

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
3
Included in the Kit
Surface Mount – 24VAC Kit
Kit will be labeled: D-PK-3-24-S
• 24VAC Power Harness (18 AWG), Orange, Green, Yellow
Kit will be labeled: D-MK-WLL-PLTC-1
• 4 - 6-32 x 1” Machine Flat Screws
• 4 - 6-19 x 1/2” Flat Head Screws
• 4 - 8-32 x 7/19” Screws
• 2 - 8-32 x 7/16” Screws
Surface Mount - 120VAC or 240VAC Kit
Kit will be labeled: D-PK-3-110-S
• 120VAC or 240VAC Harness (18 AWG), Black, Green, White
Kit will be labeled: D-MK-WLL-PLTC-1
• 4 - 6-32 x 1” Machine Flat Screws
• 4 - 6-19 x 1/2” Flat Head Screws
• 4 - 8-32 x 7/19” Screws
• 2 - 8-32 x 7/16” Screws
Below is a list of all the items included in the SBL 3000 installation kit. The items in the kit will correspond to the type of mounting and voltage
option chosen.
Installation

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
4
ABS Surface (Wall) Mount Installation
e
w
q
r
t
y
Installation

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
5
1. Mount Housing to Wall and/or Gang Box - To mount the housing to the wall, install two (2) wall anchors into the wall (not supplied
in kit) and take two pan head screws no larger than #8 (also not supplied in kit) and drive them into the anchors leaving an 1/8th inch
gap between the head of the screw and the wall. Mount the housing to the wall by lining up the two keyholes in the back of the housing
with the two screws with the 1/8 inch gap and slide the housing onto the heads of the screws. Next, mark the 2 mounting holes at the
bottom of the housing on the wall. Remove the housing and install wall anchors at this location. Hang the housing on the keyholes and
install the bottom screws. To mount the housing to the gang box, take the four (4) 6-32 x 1” screws (supplied in kit) and screw them
through the four holes in the center of the inside of the housing and the four holes in the gang box.
Note: If using a metal gang box, a ground must be provided to the gang box.
2. Feed Wiring Into the Housing - Take the wire coming from the inside of the gang box and feed it through the hole in the middle of
the housing.
3. Plug and Secure Wiring - Loosen the provided wire clamp (comes attached to the inside of the housing) and slip excess wiring
through and tighten the clamp. After securing excess wiring, connect the wiring into the appropriate connector on the back of the
display board. (See the Wiring and Jumper Settings on page 9-11).
4. Mount Display Board to Housing - Using the four (4) self tapping, 6-19 x 1/2” flat head screws (supplied in the assembly kit), take
the display board and screw it to the front side of the clock housing (4 screws per clock).
5. Snap on Filter - Take the red filter bezel and snap it on to the front side of the housing.
6. Snap on Frame - Take the gray frame and snap it on to the front side of the housing.
ABS Surface (Wall) Mount Installation (continued)
Installation

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
6
ABS Double Mount Installation
qt
i
a
y
r
w
w
e
u
o
Installation

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
7
ABS Double Mount Installation (continued)
*For metal mounting bracket: Use a wall anchor that can support 50 lbs or more with a maximum
screw size of #8
1. Install metal mounting bracket - First, remove the metal mounting bracket from the inside of the double mount base by unscrewing
the two (2) 6-32 x 1/2” screws located on the underside of the base (save these screws for step #5). Next, screw the metal mounting
bracket to the wall or ceiling in which the clocks are being installed. To mount to the double gang switch box, screw the four (4) 6-32 x
1” screws (supplied in the assembly kit) through the inner four holes of the metal mounting bracket. Use the outer four holes to mount to
the anchors in the wall (both anchors and screws are not supplied in kit).
Note: If using a plastic switch box, a ground wire must be routed through the switch box and into one (1) of
the four (4) metal mounting bracket screws in order to provide ground to the metal mounting bracket. The metal
mounting bracket
MUST
be secured by both the screws going to the switch box
AND
the anchors going into the
wall.
2. Mount clock housings to pole - Align the hole in the center each housing with one of the three holes on the mounting pole where
the wiring will be routed (the installer will choose which hole at the end of the pole to use based on how far they want the clock to sit
from the wall). Screw from the inside of the housing into the four holes surrounding the hole in the center of the housing using the four
(4) 8-32 x 7/16” screws (supplied in the assembly kit - 4 screws per clock), securing both housings to the mounting pole.
Note: End caps from one side of each clock must be removed to mount both clocks to the mounting pole.
Remove one end cap from each clock from the side in which the mounting pole enters the clock.
*Instructions continued on next page
3. Screw both housings together - Using the two (2) self tapping, 6-19 x 7/16” screws (supplied in the assembly kit), screw both back
sides of the clock housings together (2 screws per clock).
Installation

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
8
ABS Double Mount Installation (continued)
4. Feed wiring through base and pole - Take the wiring coming from the switch box and begin to feed it through the center of the
base of the mounting assembly until it emerges from the hole in the center of the clock housing.Make sure there is roughly 1.5’ of
wiring coming from the switch box. Perform this task for both clocks.
5. Snap and screw base to metal mounting bracket - Snap the base to the metal mounting bracket by first making contact with
the lip in the upper side of the base and the metal mounting bracket. When the base has been snapped onto the bracket, take
the two (2) 6-32 x 1/2” pan head screws that originally came installed on the base and screw them back into the two holes on the
underside of the base to secure the base to the metal mounting bracket.
6. Connect switch box wires to clock harness - Take the wiring harness supplied with the clock and make all necessary
connections between the wiring harness and the switch box wires using wire nuts. Perform this task for both clocks.
7. Plug and secure wiring - Loosen and slip excess wiring through provided wire clamp (comes attached to each housing) and
tighten the clamp. After securing excess wiring, connect the wiring harness into the appropriate connector on the back of the
display board. Perform this task for both clocks. (See the Wiring and Jumper Settings on page 9-11).
8. Mount display board to housing - Using the four (4) self tapping, 6-19 x 1/2" flat head screws supplied in the assembly kit,
take the display board and screw it to the front side of the clock housing (4 screws per clock).
9. Snap on filter - Take the red filter bezel and snap it on to the front side of each clock housing.
10. Snap on frame - Take the gray frame and snap it on to the front side of each clock housing.
Installation

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
9
Wiring Information
Wiring and Jumper Settings (3100 Series)
**Jumper Position
JP 1 JP 4 JP 5
JP 6
JP 2
JP 3
Power Settings
1
4 5
2
3
24VAC @ 0.35A (ORG)
120VAC or 240VAC @ 0.1A (BLK)
No Connection
120VAC or 240VAC @ 0.1A (WHT)
24VAC @ 0.35A (YEL)
Note: When setting up the jumpers, Pin 1 & Pin 2 must be jumpered together OR Pin 2 & Pin 3 must be jumpered together. Below are the Jumper Positions and what function each corresponds with.
Pin
1 2 3
Jumper Position Pin 1 & Pin 2 Pin 2 & Pin 3
JP 1 12 Hour Time 24 Hour Time JP 2 Bright Dim JP 3 Time Display Only Alternating Date/Time Display JP 4 Normal Configuration JP 5 Real Time Clock 60Hz JP 6 Sync RS485 Select
Wiring Information
Note: Pin 1 will always be the square pad.

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
10
Wiring Information
Wiring and Jumper Settings (3200 Series)
**Jumper Position
JP 1 JP 4 JP 5
JP 6
JP 2
JP 3
Power Settings
1
4 5
2
3
24VAC @ 0.35A (ORG)
120VAC or 240VAC @ 0.1A (BLK)
No Connection
120VAC or 240VAC @ 0.1A (WHT)
24VAC @ 0.35A (YEL)
Elapsed Timer
5
2 1
4
3
No Connection TXD (Blue&Blue/White)
Common (Green&Green/White) RXD (Orange&Orange/White) 3.3V@0.1A (Brown&Brown/White)
P1 - Sync Inputs P2 - User Inputs
P3 - Relay Output
4 3
2
1
*Relay 1 N.O.
*Relay 2 N.O.
Note: When setting up the jumpers, Pin 1 & Pin 2 must be jumpered together OR Pin 2 & Pin 3 must be jumpered together. Below are the Jumper Positions and what function each corresponds with.
Pin
1 2 3
Jumper Position Pin 1 & Pin 2 Pin 2 & Pin 3
JP 1 12 Hour Time 24 Hour Time JP 2 Bright Dim JP 3 Time Display Only Alternating Date/Time Display JP 4 Normal Configuration JP 5 Real Time Clock 60Hz JP 6 Sync RS485 Select
Cat 5 Cable
Wiring Information
J7 - RS485
1 2 3 4
Input A Input B
Output A
Output B
Note: Pin 1 will always be the square pad.

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
11
Wiring Information
Wiring and Jumper Settings (3300 Series)
**Jumper Position
JP 1 JP 4 JP 5
JP 6
JP 2
JP 3
Power Settings
1
4 5
2
3
24VAC @ 0.35A (ORG)
120VAC or 240VAC @ 0.1A (BLK)
No Connection
120VAC or 240VAC @ 0.1A (WHT)
24VAC @ 0.35A (YEL)
Elapsed Timer
5
2 1
4
3
No Connection TXD (Blue&Blue/White)
Common (Green&Green/White) RXD (Orange&Orange/White) 3.3V@0.1A (Brown&Brown/White)
J1 - Sync Inputs J2 - User Inputs
12 3 4 5 6 7 8 9 12 3 4 5 6 7 8 9
AC / DC Com
120VAC or 240VAC Sync
24VAC Sync Dukane Reset
Dukane Pulse
Dry Contact
3.3VDC@20ma
Common
Common
User Input 4 User Input 3 User Input 2 User Input 1 12VDC@40ma
Each User Input is a Contact Closure
J3 - Relay Output
4 3
2
1
*Relay 1 N.O.
*Relay 2 N.O.
*Contact Rating 0.3A @ 120VAC 0.5A @ 24 VAC
Note: When setting up the jumpers, Pin 1 & Pin 2 must be jumpered together OR Pin 2 & Pin 3 must be jumpered together. Below are the Jumper Positions and what function each corresponds with.
Pin
1 2 3
Jumper Position Pin 1 & Pin 2 Pin 2 & Pin 3
JP 1 12 Hour Time 24 Hour Time JP 2 Bright Dim JP 3 Time Display Only Alternating Date/Time Display JP 4 Normal Configuration JP 5 Real Time Clock 60Hz JP 6 Sync RS485 Select
Cat 5 Cable
Wiring Information
J7 - RS485
1 2 3 4
Input A Input B
Output A
Output B
Note: Pin 1 will always be the square pad.

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
12
Using the Output Sync Relay (SBL 3300 Series Only)
Intercom, paging system, or other device
Wiring Information
Output Relay
Green
White
(Relay 1) J3 - 1 & 2
or
(Relay 2) J3 - 3 & 4
Relay Input
Wiring Information

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
Temperature Sensor Wiring (Optional)
If you ordered a Temperature Sensor with your SBL 3200/3300 clock, it must be connected to a terminal on the Clock.
Connecting The Temperature Sensor
Temperature Sensor
Sensor Cable
(IMPORTANT: Detach clock from power source before installing new circuitry. DO NOT add new circuitry while the clock is operating)
Attach the end of the Temperature Sensor Wire to the circuit board in the following manner:
Data from the temperature sensor will be sent to your clock when the
clock is powered on. For more information on how to make the SBL
display temperature, please see the section labeled “Web Interface -
Display Settings”.
The Sensor Cable is 6 feet (1.83 meters) long, and so the sensor
should be positioned within 6 feet of the clock. The cable is
unshielded, 4 conductor, 22AWG (.33mm²). If longer than 6 feet is
required, the wire would have to be terminated in an electrical box,
and the longer wire would have to be provided by the customer.
1
2
3
4
5
5) No connection
4) White
3) Black
2) Green
1) Red
13
Wiring Information
Please Note: The board depicted below is related to
the 3300 series digital clock. If you have purchased the
3200 series digital clock, the Temperature Sensor will
connect in the same manner.

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
14
Wiring Information
Buzzer Installation (3300 Series)
J1 - Sync Inputs
12 3 4 5 6 7 8 9
J3 - Relay Output
4
3
2
1
*Relay 1 N.O.
*Relay 2 N.O.
Wiring Information
If you ordered a Buzzer with your SBL 3300 clock, it can be installed on the clock circuit board with four easy steps:
1) Attach the long green connector to the J1 Sync Input ports.
2) Confirm that the wires are attached to holes 7 and 8. The red wire should be in hole 7. The black wire should be in hole 8.
3) Attach the short green connector to the J3 Relay Output ports.
4) Confirm that the wires are attached to holes 1 and 2. The yellow wire should be in hole 1. The black wire should be in hole 2.
(IMPORTANT: Detach clock from power source before installing new circuitry. DO NOT add new circuitry while the clock is operating)
To program the buzzer, connect the USB cable to the clock, log onto SBDConfig and perform the following actions:
1) Click on the Elapsed Timer tab.
2) Find the drop-down menu next to “On Countdown complete, close” and select “Relay 2”
3) In “for ____ seconds” set the amount of time that you wish the buzzer to sound when the countdown ends. The number
must be a whole number from 1 to 60.
4) Press the Update Clock button.

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
15
Programming
Setting the Time (SBL 3300 Series Only)
1. To set the time, press the top button to set the hour and the bottom button to set the minute.
Programming the SBL 3300
1. To enter programming mode, simultaneously press the top and bottom buttons.
2. Press the top button to select an Option. Hold the button down to scroll through the Options.
3. Press the bottom button to select a Setting. Hold the button down to scroll through the Settings.
4. To return to time while in an Option, simultaneously press the top and bottom buttons.
Option 1 - Set Year:
This option will allow the user to set the current year.
Press the bottom button to scroll between “01-99” on the display in
order to set the year.
Once the year is selected, press the top button to continue on to
Option 2.
Option 2 - Set Month:
This option will allow the user to set the current month.
Press the bottom button to scroll between “01-12” on the display to set
the month.
Once the month is selected, press the top button to continue on to
Option 3.
Set Hour
Set Minute
1 12
OPTION SETTING
2 12
Programming

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
16
Option 3 - Set Day:
This option will allow the user to set the current date.
Press the bottom button to scroll between “01-31” on the display to
set the date.
Once the date is selected, press the top button to continue on to
Option 4.
Option 4 - Set 12/24 Hour Format:
This option will allow the user to select the mode the time is displayed
in. There are two options: 12 hour format or 24 hour format.
Press the bottom button to scroll between "12 or 24.”
Once 12 hour format or 24 hour format is selected, press the top
button to continue on to Option 5.
Option 5 - Daylight Saving Time:
This option will allow the user to select the Daylight Saving Time setting.
Press the bottom button to scroll between “Eor d.”
Option “E” will enable the current USA Daylight Saving Time
schedule seen below:
• DST starts 2nd Sunday of March at 2:00 am
• DST ends 1st Sunday of November at 2:00 am
Option “d” will disable the Daylight Saving Time setting. Note: If a
different Daylight Saving Time setting is needed, it must be configured
via the web interface. See page 38 for more information.
Once the Daylight Saving Time option is selected, press the top button
to continue on to Option 6.
Option 6 - Alternating Date/Time:
This option will allow the user to enable or disable the Alternating Time/
Date display. Press the bottom button to scroll between “Eor d.”
When enabled (E), the display will switch between showing the time
(HH:MM:SS) and the date (MM:DD:YY) for 6 digit, (HH:MM) and
(MM:DD) for 4 digit. When disabled (d), the display will show only the
time.
Once the Alternating Date/Time option is selected, press the top button
to continue on to Option 7.
4 24
5 d
6 d
OPTION SETTING
3 21
Programming

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
17
Option 7 - American or European Date Style:
This option will allow the user to choose what style the date is displayed
on the digital clock. Press the bottom button to scroll between “A” or
“E.”
“A” stands for American style and displays the date as follows: month,
day and year (ex. 10 28 12). “E” stands for European style and displays
the date as follows: day, month and year (ex. 28 10 12).
The date will be displayed during normal operation only if the
“Alternate Time/Date” option has been enabled in Option 6.
Once the date style is selected, press the top button to continue on to
Option 8.
Option 8 - Brightness:
This option allows the user to choose the brightness level the digital
clock will display. Press the bottom button to scroll between “00,” “01”
and “02.”
• Level “02” is High (default)
• Level “01” is Medium
• Level “00” is Low
Note: The user has the ability to create a Brightness Schedule for the
clocks. Refer to page 30 for more information.
Once the brightness level is selected, press the top button to continue
on to Option 9.
Option 9 - Set the Clock Number:
This option allows the user to choose a specific clock number in order to
easily identify a specific clock within the system. Use the bottom button
to scroll between “1-999.”
An example of a clock number is “123.”
Once the clock number is selected, press the top button to continue on
to Option 10.
Options 9also allows a user to address a specific clock for displaying
messages, such as 911, BELL or FiRE using a Sapling Master Clock.
Option 9sets the clock number. This is step 1 of 2. Step 2 of this
process can be completed in Option 10.
Option 10 - Set the Zone Number:
This option allows the user to choose a zone number for a specific
clock. A zone number is a collection or grouping of clocks within a
certain section of a facility. Press the bottom button to scroll between
"01-99."”
An example of a zone number is “12.”
Once the zone number is selected, press the top button to continue on
to Option 11.
Option 10 programs the zone number in order to display
messages on each clock in a zone, such as 911, BELL or FiRE.
Note: The message feature must be programmed via the master clock.
Refer to the specific master clock manual for more information.
9 1
10 01
8 02
OPTION SETTING
7 A
Programming

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
18
Option 11 - RS485 Data Rate:
This options allows a user to set the RS485 data rate. The RS485 data
rate is the rate at which data (for example the time and/or date) is sent
to the clock.
Press the bottom button to scroll between “00-12.” See Table 1 for
RS485 Data Rate settings.
Once the RS485 Data Rate is selected, press the top button to continue
on to Option 13.
Option 13 - Loss of Communication Alert:
This option allows the user to enable or disable the Loss of
Communication Alert on the digital clock display. The digital clock will
signal a loss of communication with the master clock by blinking the
colons on the display. Press the bottom button to scroll between “E - d.”
Enabling this option (E) will allow the user to proceed to option 14 to
configure the loss of communication alert. Disabling this option (d) will
keep the colons solid and not show a loss of communication. Disabling
should be used when the clock is in independent mode.
If a user has chosen to enable (E) the Loss of Communication Alert, when
the top button is pressed, the user will be taken to option 14. If a user
chooses to disable (d) the Loss of Communication Alert, when the top
button is pressed, the user will be taken to option 15.
Option 14 - Set the Loss of Communication Alert:
This option will allow the user to choose at what point the colons will
blink after communication with the master clock is lost. Press the bottom
button to scroll between “01-10.”
See Table 2 below for settings.
Once the Loss of Communication Alert setting is selected, press the top
button to continue on to Option 15.
14 06 Table 2
01 - Data is lost after 5 minutes 06 - Data is lost after 60 minutes
02 - Data is lost after 10 minutes 07 - Data is lost after 90 minutes
03 - Data is lost after 15 minutes 08 - Data is lost after 120 minutes
04 - Data is lost after 30 minutes 09 - Data is lost after 180 minutes
05 - Data is lost after 45 minutes 10 - Data is lost after 240 minutes
13 E
OPTION SETTING
00 - Data is off 07 - Data is transmitted every 2 minutes
01 - Data is transmitted every second 08 - Data is transmitted every 5 minutes
02 - Data is transmitted every 5 seconds 09 - Data is transmitted every 10 minutes
03 - Data is transmitted every 10 seconds 10 - Data is transmitted every 15 minutes
04 - Data is transmitted every 15 seconds 11 - Data is transmitted every 30 minutes
05 - Data is transmitted every 30 seconds 12 - Data is transmitted every hour
06 - Data is transmitted every minute
Table 1
11 01
Programming

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
19
dDisable the relay selection mode.
01 58th minute (1) - The hourly correction for 55 seconds every hour from XX:58:05 to XX:59:00. The daily correction (5 a.m. &
5 p.m.) is ten correction cycles sent to the relay (each for 95 seconds) beginning at 5:05:00, 5:07:00, 5:09:00, 5:11:00, 5:13:00,
5:15:00, 5:17:00, 5:19:00, 5:21:00, and 5:23:00.
02 58th minute (2) - The hourly correction for 60 seconds every hour from XX:58:00 to XX:59:00. The daily correction (5 a.m. & 5
p.m.) is twelve correction cycles sent to the relay (each for 65 seconds on and 25 seconds off) beginning at 5:05:00 to 5:22:35.
03 58th minute (3) - The hourly correction for 60 seconds every hour from XX:58:00 to XX:59:00. The daily correction (5 a.m. & 5
p.m.) is twelve correction cycles sent to the relay (each for one minute on and two minutes off) beginning at 5:06:00.
04 58th minute (4) - The hourly correction for 55 seconds every hour from XX:58:05 to XX:59:00. The daily correction (5 a.m. &
5 p.m.) is 12 correction cycles for 55 seconds. The timings will be 05:03:05, 05:07:05, 05:11:05, 05:15:05, 05:19:05, 05:23:05,
05:27:05, 05:31:05, 05:35:05, 05:39:05, 05:43:05 and 05:47:05.
05 59th minute - The hourly correction for 8 seconds every hour from XX:57:54 to XX:58:02. The daily correction (5 a.m. & 5 p.m.)
is a 14 second pulse from 5:57:54 to 5:58:08.
06 National Time & Rauland (1) - The hourly correction is for 25 seconds every hour from XX:00:00 to XX:00:25. The daily
correction is a 24 minute pulse from 6:00:25 to 6:24:25 AM and PM.
07 National Time & Rauland (2) - The hourly correction is for 25 seconds every hour from XX:00:00 to XX:00:25. The daily
correction (6 a.m. & 6 p.m.) is 25 seconds on, 35 seconds off every minute for 24 minutes.
08 Rauland Digital - Every .5 second advances the time 1 minute from 12:00:00 a.m.
09 Once a Day Pulse - If selected, this option will allow the user to set the hours, minutes, and seconds for relay closure.
Table 3 - Relay Selection Mode
Option 20 - Set the Programmable Relays:
This option will allow the user to set the programmable relays.
The programmable relays allow a user to choose the type of
time correction the clocks will conduct when the clocks reach
a certain time. Press the bottom button to scroll between “d”
and “01-09.”
If Option 20 is set to “d” (disable) or “01-08,” when the top
button is pressed, the user will be taken to Option 30. If option
“09” is selected, the user will be taken to options “21-24” to
configure the Once a Day Pulse settings.
See Table 3 below for explanation of relay selection mode for
time correction.
Note: Refer to page 12 for wiring information.
20 08
Option 15 - Enable Jumpers:
This option will allow the user to enable or disable the jumpers
inside the clock. There are 3 jumpers located inside the clock
that are associated with this option:
• Jumper 1 - 12/24 Hour Format
• Jumper 2 - Brightness Level
• Jumper 3 - Alternating Date/Time
Press the bottom button to scroll between “E-d.”
Selecting (E) will allow the user to set the jumpers and selecting
(d) will disable the jumpers. Once a user enables or disables the
jumpers, press the top button to continue on to Option 20.
Note: Enabling this option will override the previously
configured settings for options 4, 6 and 8.
15 d
OPTION SETTING
Programming

The Sapling Company, Inc.
1633 Republic Road
Huntingdon Valley, PA 19006
USA
+1 215.322.6063 P.
+1 215.322.8498 F.
www.sapling-inc.com
20
Option 21 - Once a Day Pulse Output - Hour:
If the Once a Day Pulse setting is selected in Option 20, a user will need
to set the hour(s) for relay closure. Press the bottom button to scroll
between “00-23.”
Once a user selects the Once a Day Pulse Output - Hour(s), press the top
button to continue on to Option 22.
Option 22 - Once a Day Pulse Output - Minutes:
If the Once a Day Pulse setting is selected in Option 20, a user will need
to set the minute(s) for relay closure. Press the bottom button to scroll
between “00-59.”
Once a user selects the Once a Day Pulse Output - Minute(s), press the
top button to continue on to Option 23.
Option 23 - Once a Day Pulse Output - Seconds:
If the Once a Day Pulse setting is selected in Option 20, a user will need
to set the second(s) for relay closure. Press the bottom button to scroll
between “00-59.”
Once a user selects the Once a Day Pulse Output - Second(s), press
the top button to continue on to Option 24.
Option 24 - Once a Day Pulse Output - Set Duration:
This option allows the user to set the duration in second(s) for relay
closure. Press the bottom button to scroll between “01-99.”
Once a user selects the duration number, press the top button to
continue on to Option 30.
24 99
OPTION SETTING
23 59
21 23
22 59
Programming