Satec Expertmeter Series User manual

EM132-133 QUICK START GUIDE
BG0504 REV.A2
Quick Start Guide
EM132-133

EM132-133 QUICK START GUIDE
BG0504 REV.A2
2
Mechanical Installation
Figure 1: Instrument Dimensions

EM132-133 QUICK START GUIDE
BG0504 REV.A2
Mechanical Installation
Figure 2: Mounting the EM133 on DIN Rail or on flat surface
IMPORTANT!
Only qualified personnel can perform setup.
All incoming power sources must be turned off during installation. During operation of the Powermeter,
hazardous voltages are present on the input terminals. Failure to observe precautions can result in
serious or even fatal injury, or damage to equipment.
Please refer to the installation and operation manual for further information.

EM132-133 QUICK START GUIDE
BG0504 REV.A2
4
NOTE:
Refer to the Installation and operation
manual for the wiring schematics
diagrams
Typical Electrical Installation
Figure 3:Common Wiring Mode: 4LL3 or 4Ln3
Wiring Configuration
Setup Code
3-wire 2-element Direct connection using 2 CTs
3dir2
4-wire Wye 3-element direct connection using 3 CTs
4Ln3 or 4LL3
4-wire Wye 3-element connection using 3 PTs, 3 CTs
4Ln3 or 4LL3
3-wire 2-element Open Delta connection using 2 PTs, 2 CTs
3OP2
4-wire Wye 2½ -element connection using 2 PTs, 3 CTs
3Ln3 or 3LL3
3-wire 2½ -element Open Delta connection using 2 PTs, 3 CTs
3OP3
4-wire 3-element Delta direct connection using 3 CTs
4Ln3 or 4LL3
3-wire 2½-element Broken Delta connection using 2 PTs, 3 CTs
3bLn3 or 3bLL3

EM132-133 QUICK START GUIDE
BG0504 REV.A2
5
Electrical Installation
Figure 4: CT Wiring options

EM132-133 QUICK START GUIDE
BG0504 REV.A2
6
MODULE Installation
This section applies to the I/O and Communication modules.
Figure 5: PM130 PLUS modules
Figure 6: Mounting module
CAUTION!
Before I/O Module installation ensure that all incoming power sources are shut OFF. Failure to
observe this practice can result in serious or even fatal injury and damage to equipment.
NOTE:
Refer to the Installation and operation
manual for the wiring schematics
diagrams and setup parameters
MODULE
4 ANALOG OUT
MODULE
ETHERNET
MODULE
4DI/2DO
Module
Connector
Module Connector Cover
Remove Module Connector Cover
before assembling module

EM132-133 QUICK START GUIDE
BG0504 REV.A2
7
Basic Setup
All setups can be performed directly from the display panel or via communication ports using PAS communication
software, except for Communications and Display setups, which must be performed directly at the instrument panel.
To set the CT Primary current, perform the following steps:
Press for 5sec, until password no. blinks:
Enter Password number using , then press for 2sec
then new display with blinking "Reset"
Navigate by pressing shortly (less than 1sec)
to move to Basic setup
Press for 2sec, until "Conf" blinks:
Navigate by pressing shortly (less than 1sec)
to move to CT setup
Press for 2sec, until "5000" blinks, then press shortly using to the desired value
Press for 2sec, until "CT" blinks, then press for 2sec, until "Basic" blinks, then press for
2sec, until "Reset" blinks, press shortly using to move to blinking "Exit" and press for 2sec to return
to initial screen

EM132-133 QUICK START GUIDE
BG0504 REV.A2
8
DATA DISPLAY
Navigating in Display Mode
The front panel has a simple interface that allows you to display numerous measurement parameters in
up to 38 display pages. For easier reading, the parameters are divided into three groups; each group is
accessible by pressing the key and each group page is accessible by pressing the key.
The initial display is as described below:
First push on will display Energy measurement parameters, by pushing will navigate to imp.,
exp. active/reactive, etc …as described below:
Second push on will display MAX DMD parameters, by pushing will navigate to MAX DMD P,
Q, S, I, etc …as described below:
Third push on will display Votage/Current measurements, by pushing will navigate to V (L-N),
V (L-L), I, Power, PF, THD, TDD, F, etc …as described below:

EM132-133 QUICK START GUIDE
BG0504 REV.A2
9
Basic Menu
Code
Parameter
Options
Description
ConF
Wiring mode
3OP2
3-wire open delta using 2 CTs
4Ln3
4-wire Wye using 3 PTs (default)
3dir2
3-wire direct connection using 2 CTs
4LL3
4-wire Wye using 3 PTs
3OP3
3-wire open delta using 3 CTs
3Ln3
4-wire Wye using 2 PTs
3LL3
4-wire Wye using 2 PTs
3bLn3
3-wire Broken delta using 2 PTs, 3 CTs
3bLL3
3-wire Broken delta using 2 PTs, 3 CTs
Pt Ratio
PT ratio
1.0- 6,500.0
The potential transformer ratio
Pt Factor
Ct
CT primary current
1-50,000A
(5*)
The primary rating of the current transformer
PowDmdPer
Power demand period
1, 2, 5, 10, 15*, 20,
30, 60, E
The length of the period for power demand calculations, in
minutes. E = external synchronization
Num.Per.
Number of power
demand periods
1-15
(1*)
The number of demand periods to be averaged for sliding window
demands
1 = block interval demand calculation
ADmdPer.
Ampere/Volt demand
period
0-1800
(900*)
The length of the period for volt/ampere demand calculations, in
seconds. 0 = measuring peak current
Frequency
Nominal frequency
25, 50, 60, 400 (Hz)
The nominal power utility frequency
MaxDmdLd
- Default setup
Communication Port Menu
COM1 setting
Code
Parameter
Options
Description
Protocol
Communications protocol
ASCII, rtu, dnP3
ASCII, Modbus RTU (default) or DNP3.0
protocol
Interface
Interface standard
485
RS-485 interface (default)
Address
Address
ASCII: 0 (default) - 99, Modbus: 1 (default) -247, DNP3.0: 0 (default) -255
Baud Rate
Baud rate
110, 300, 600, 1200, 2400, 4800, 9600 (default), up to 115,200 bps
Data/Party
Data format
7E, 8E (7/8 bits, even parity), 8n (default) (8 bits, no parity)
Snd.Delay

EM132-133 QUICK START GUIDE
BG0504 REV.A2
10
Input and Output Ratings
DIRECT INPUT - Nominal: 690V line-to-line voltage, 828V maximum;
400V line-to-neutral, 480V maximum - Burden: <0.5 VA. INPUT USING PT
- Burden: <0.15 VA
57/98-400/690 VAC
3 voltage inputs
4 x Maximum wire section: 2.5 mm²(12 AWG)
Voltage input terminals
INPUT VIA CT with 5A secondary output - Burden: <0.2VA, Overload
withstands: 20A RMS continuous, 300A RMS for 0.5 second.
/5A(10A)
3 current nputs
(Galvanic isolation)
INPUT VIA CT with 1A secondary output - Burden: <0.05VA, Overload
withstands: 3A RMS continuous, 80A RMS for 0.5 second.
/1A(2A)
INPUT VIA CT with 50A direct connection - Burden: < 0.05VA, Overload
withstands: 120A RMS continuous, 2000A RMS for 0.5 second.
50A(100A)
INPUT VIA CT with 40mA secondary output, using external CT –Split
Core CT or Solid Core CT –primary 100-1200A maximum rating
40mA:(optional)
3 x Maximum wire section: 16 mm²
Current input terminals
Optically isolated, max. speed 115.2Kb/s
EIA RS-485 standard
Communication port
COM1
3 x Maximum wire section: 2.5 mm²
COM1 terminals
Infra Red, max. speed 38.4Kb/s
IR COM port
Communication port
COM3
50/60 Hz - 9VA
40-300V AC/DC
(standard)
Power Supply
(Galvanically
isolated)
3 x Maximum wire section: 2.5 mm²
Power Supply input
terminals
Dry contact, internally wetted @ 5VDC
DIGITAL INPUT x 2
optically isolated inputs
MODULE 2DI/DO
0.15A/250 VAC - 400 VDC, 1 contact (SPST Form A)
DIGITAL OUTPUT x 1
5 x Maximum wire section: 2.5 mm²
2DI/DO terminals
Dry contact, internally wetted @ 24VDC
DIGITAL INPUT x 2
optically isolated inputs
MODULE 4DI/2DO
(Optional)
5A/250 VAC; 5A/30 VDC, 1 contact (SPST Form A)
EMR
DIGITAL
OUTPUT x 2
0.15A/250 VAC - 400 VDC, 1 contact (SPST Form A)
SSR
9 x Maximum wire section: 2.5 mm²
4DI/2DO terminals
1 mA, maximum load 5 k(100% overload)
ANALOG OUT x 4
optically isolated
outputs
(4 different options)
MODULE 4 AO
(Optional)
0-20 mA, maximum load 510 
4-20 mA, maximum load 510 
0-1 mA, maximum load 5 k (100% overload)
5 x Maximum wire section: 2.5 mm²
4 AO terminals
10/100 Base T, auto adaptation speed, Max. speed 100Mb/s
Ethernet
Communication port
COM2 (Optional)
Shielded RJ45 cable
ETH connector
Max. speed 12 Mb/s
Profibus
Communication port
COM2 (Optional)
5 x Maximum wire section: 2.5 mm2 (12 AWG) or using terminal to DB9
converter: P/N AC0153 REV.A2
Profibus terminals
Optically isolated, max. speed 115.2Kb/s –to be connected to GPRS
modem if ordered
EIA RS-232-422/485
standard
Communication port
COM2 (Optional)
5 x Maximum wire section: 2.5 mm²
And DB9 connector
COM2 terminals